IKSLED Touch switch sensor

Contents

LED Dimmer Touch Sensor Control Switch User Manual

Model: Touch switch sensor

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your LED Dimmer Touch Sensor Control Switch. Please read this manual carefully before use to ensure proper function and safety.

2. Key Features

  • Dual Memory Function: Remembers the last brightness setting and on/off status before power-off.
  • Touch Control: Simple touch for On/Off and stepless dimming.
  • Adjustable Brightness: Long press to achieve stepless dimming from 0% to 100%.
  • Indicator Light Control: Quick double-tap to turn the blue indicator light on or off.
  • Wide Voltage Compatibility: Supports DC 3V, 3.7V, 5V, 12V, and 24V systems.
Touch Sensor with Memory Function

Figure 1: Touch Sensor with Dual Memory Function (Brightness 0% to 100%)

Dual Memory Function Explanation

Figure 2: Explanation of Dual Memory Function

3. Setup and Installation

3.1 Wiring Diagram

Wiring Diagram for Touch Sensor Switch

Figure 3: Wiring Diagram. Connect Power+ to positive input, LED+ to positive output, Power- to negative input, and LED- to negative output.

3.2 Wiring Instructions

  1. Connect the wires exactly as shown in the wiring diagram (Figure 3). Ensure correct polarity for input (Power+, Power-) and output (LED+, LED-).
  2. Verify that the working voltage of your power adapter matches the LED light and the switch (e.g., 3.7V, 5V, 12V, or 24V DC).

3.3 Fixing the Switch

  1. Drill a 17mm diameter hole in your desired mounting surface (e.g., cabinet, wall).
  2. Insert the touch sensor switch into the hole and securely fix it in place to prevent movement during use.
Installation Dimensions and 17mm Hole

Figure 4: Switch dimensions and 17mm installation hole requirement.

3.4 Power On

After completing wiring and installation, turn on the power supply to begin using the switch.

4. Operating Instructions

The touch sensor switch offers intuitive control over your LED lighting.

  1. Turn On/Off: Short touch the sensor surface to toggle the LED light on or off.
  2. Adjust Brightness (Stepless Dimming): When the light is on, long press the sensor surface to gradually increase or decrease the brightness. Release your finger when the desired brightness is reached.
  3. Control Indicator Light: Quick double-tap the sensor surface to turn the blue indicator light on or off.
Press to Turn On/Off

Figure 5: Short touch to turn the light On/Off.

Adjust LED Brightness

Figure 6: Long press to adjust LED brightness (0% to 100%).

Indicator Light Control

Figure 7: Quick double-tap to open/close the indicator light.

4.1 Product Demonstration Video

Video 1: Demonstration of touch on/off, indicator control, dimming, and memory functions.

5. Specifications

ParameterDetails
Brand NameIKSLED
Model NumberTouch switch sensor
MaterialPlastic
Switch TypeTouch On/Off Switch
Working VoltageDC 3V, 3.7V, 5V, 12V, 24V
Max. Load3V, < 5W / 3.7V, < 7W / 5V, < 12W / 12V, < 36W / 24V, < 48W
Current3A
Sensing MethodShort touch: Turn On/Off; Long press: Stepless dimming
DimmableYes
Installation Hole Size17mm
Weight6g
CertificationSAA, RoHS, LVD, FCC, EMC, CE, CCC

6. Usage Precautions

WARNING: This induction switch is prohibited from being used to control the following equipment:

  • Motors
  • Solenoid valves
  • Solar lights
  • Constant current lamps
  • Other inductive loads

Using the switch with these types of equipment may cause malfunction or damage to the switch or the connected device.

7. Maintenance

This touch sensor switch requires minimal maintenance. Keep the sensor surface clean and dry. Avoid using abrasive cleaners or solvents, which may damage the plastic material or the sensor functionality. Ensure all connections remain secure.

8. Troubleshooting

Symptom: Light cannot be controlled

After connection, the LED light stays permanently on or permanently off, and cannot be controlled by the switch.

Possible Causes and Solutions:

  1. Voltage Mismatch:
    Cause: The working voltage of the power adapter does not match the LED light or the switch.
    Solution: Confirm that your power adapter is a constant voltage DC power supply (e.g., 3.7V, 5V, 12V, 24V) and that the LED light requires the same voltage.
  2. Reverse Polarity:
    Cause: The input/output or positive/negative (+/-) poles are connected in reverse.
    Solution: Verify the connections for input/output and positive/negative poles according to the wiring diagram. If reversed, disconnect the power and reconnect them correctly.
  3. Installation Error:
    Cause: The switch was fixed after power-on, or it is not fixed securely and keeps moving during use, causing it to constantly re-detect the environment.
    Solution: Turn off the power. Securely fix the induction switch in place to prevent movement. Then, turn the power back on to test.

9. User Tips

  • If the blue indicator light is too bright or distracting, remember you can easily turn it off with a quick double-tap on the sensor surface.

10. Warranty and Support

This product comes with a 1-year warranty from the date of purchase. Please retain your proof of purchase for warranty claims. For technical support or warranty inquiries, please contact your retailer.


Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.