1. Introduction
The LAUNCH X431 2 In 1 TPMS RF-Sensor is a universal tire pressure monitoring system (TPMS) sensor designed for comprehensive vehicle coverage. This sensor combines both 315MHz and 433MHz frequencies into a single unit, offering broad compatibility with over 98% of OE sensors on the market. It is OE-level programmable and 100% cloneable, making it an efficient solution for TPMS maintenance and replacement. This manual provides essential information for the safe and effective use of your RF-Sensor.
2. Safety Instructions
WARNING: Please mind potential fire risk and strictly follow the instruction manual for charging and storage. For disposal, please check your local authority's website for more information and dispose of the lithium-ion battery safely in accordance with the applicable legal requirements.
- Any maintenance and repair work must be carried out by trained experts. Failure to do so may result in the failure of the TPMS sensor. LAUNCH does not assume any liability in case of faulty or incorrect installation of the unit.
- When mounting/dismounting the wheel, follow the operation guideline of the wheel changer manufacturer strictly.
- Do not race with the vehicle on which the LTR-01 RF sensor is mounted, and always keep the drive speed under 240km/h.
- To guarantee optimal performance, the sensors may only be installed with original valves and accessories provided by LAUNCH.
- Make sure to program the sensors using a LAUNCH-specific TPMS tool prior to installation.
- Do not install programmed TPMS sensors in damaged wheels.
- After installing the TPMS sensor, test the vehicle's TPMS following the steps described in the original manufacturer's user manual to confirm proper installation.
3. Product Overview & Components
The LAUNCH RF-Sensor consists of several key components designed for reliable tire pressure monitoring.

Figure 1: Main Components of the LAUNCH RF-Sensor
Components:
- Sensor Body: The main electronic unit that measures pressure and temperature.
- Valve Stem: The part that extends through the wheel rim, allowing for tire inflation and sensor mounting.
- Rubber Grommet: Provides a seal between the valve stem and the wheel rim.
- Valve Core Assembly: The internal mechanism of the valve stem that controls air flow.
- Washer & Nut: Secures the valve stem to the wheel rim.
- Cap: Protects the valve core.
- Screw: Attaches the sensor body to the valve stem.

Figure 2: Exploded View of Sensor Components
4. Setup and Installation
Proper installation is crucial for the correct functioning of the TPMS sensor. It is recommended that installation be performed by a qualified technician.

Figure 3: TPMS Sensor Installation Steps
- Loosening the Tire: Remove the valve cap and core, then fully deflate the tire. Use a bead loosener to break the tire bead. Caution: Ensure the bead loosener is facing the valve.
- Dismounting the Tire: Clamp the tire onto the tire changer. Adjust the valve to the 1 o'clock position relative to the tire fitting head. Use the tire tool to dismount the tire bead. Caution: Always observe this starting point during the entire dismounting process.
- Dismounting the Sensor: Remove the cap and nut from the valve stem. Then, carefully remove the sensor assembly from the wheel rim.
- Mounting the Sensor and Valve:
- Remove the cap and nut from the new valve stem.
- Place the valve stem through the valve hole of the rim, ensuring the sensor body is located on the inside of the rim.
- Assemble the nut back onto the valve stem and tighten it to a torque of 4 Nm. Then, tighten the cap. Caution: Ensure the nut and cap are installed on the outside of the rim.
- Remounting the Tire: Place the tire back onto the rim. Ensure the valve starts on the opposite side of the rim from the tire fitting head. Mount the tire over the rim. Caution: Strictly follow tire changer manufacturer's instructions to mount the tire.
For detailed visual instructions, please refer to the official user manual PDF available from the manufacturer: LAUNCH RF-Sensor User Manual (PDF).
5. Operating Instructions
The LAUNCH RF-Sensor is designed to be programmed and activated using compatible LAUNCH TPMS tools.
- Programming: The LAUNCH RF-Sensor is OE-level programmable and 100% cloneable. It must be programmed using a compatible LAUNCH TPMS tool (e.g., LAUNCH TSGUN, i-TPMS) prior to installation or to replace an existing sensor. Programming allows the sensor to communicate with the vehicle's TPMS system.
- Frequency: The sensor supports both 315MHz and 433MHz frequencies, automatically adapting based on the programming.
- Post-Installation: After installation and programming, test the vehicle's TPMS system following the original vehicle manufacturer's user manual to confirm proper operation and ensure the TPMS warning light is off.
6. Maintenance
- Regularly check tire pressure as recommended by your vehicle manufacturer.
- Inspect the sensor for any visible damage during tire rotations or changes.
- When replacing or servicing the sensor, always use original valves and accessories provided by LAUNCH to ensure proper sealing.
- If the sensor is externally damaged, it must be replaced to ensure safety and proper function.
7. Troubleshooting
- TPMS Warning Light On: If the TPMS warning light remains on after sensor replacement and programming, ensure all installation steps were followed correctly. Re-check tire pressure. If the issue persists, consult a professional technician or your LAUNCH TPMS tool for diagnostic codes.
- Incorrect Pressure Readings: Verify the sensor was correctly programmed for your vehicle. Ensure the tire is properly inflated to the manufacturer's specifications. External damage to the sensor can also cause incorrect readings.
- Sensor Not Detected: Confirm the sensor is compatible with your vehicle's TPMS system. Ensure the programming process was successful. A faulty sensor or TPMS receiver in the vehicle could also be the cause.
8. Specifications
| Parameter | Value |
|---|---|
| Battery Life | 4~6 years / 100,000 kilometers |
| Working Temperature | -40°C ~ 125°C |
| Storage Temperature | -40°C ~ 125°C |
| Working Humidity | ≤90% |
| Working Frequency | 433MHz / 315MHz |
| Pressure Monitoring Range | 0 ~ 800kPa |
| Pressure Reading Accuracy | ±10kPa |
| Temperature Reading Accuracy | ±5°C |
| Acceleration (G) Sensor Reading Accuracy | ±15% |
| Transmission Power | 5 ~ 8 dBm |
| Battery Power | 3.0 V |
| Dimensions (433MHz model) | 72 x 51 x 27 mm (Length x Width x Height) |
| Weight | 30g |
| Material | Aluminum Valve |
| External Testing Certification | CE |
| IP Rating | IP67 |
| Working Voltage | 3V |

Figure 4: LAUNCH 2 In 1 RF Sensor Parameters

Figure 5: Sensor Dimensions (Width: 51mm, High: 72mm)
9. Vehicle Coverage
The LAUNCH RF-Sensor offers comprehensive vehicle coverage, supporting over 98% of all Original Equipment (OE) sensors on the market across various regions.

Figure 6: Comprehensive Vehicle Coverage Map
This includes vehicles from North America, South America, Africa, Europe, Asia, and Australia, covering a wide range of American, European, and Asian car manufacturers.
10. User Tips
- Always ensure your LAUNCH programming tool is updated to the latest software version for optimal compatibility and performance with new sensor models and vehicle makes.
- Double-check the sensor frequency (315MHz or 433MHz) required for your specific vehicle model before programming.
- For best results and to avoid issues, always use genuine LAUNCH replacement parts and accessories.
11. FCC Warning
Note: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
12. Disclaimer of Warranties and Limitation of Liabilities
All information, illustrations, and specifications in this manual are based on the latest information available at the time of publication. The right is reserved to make changes at any time without notice. We shall not be liable for any direct, special, incidental, indirect damages or any economic consequential damages (including the loss of profits) due to the use of the document.
13. Warranty and Support
The sensor is guaranteed to be free from material and manufacturing defects for a period of twenty-four (24) months or for 31,000 miles, whichever comes first. This warranty covers any defects in materials or workmanship under normal use during the warranty period. Excluded from the warranty are defects due to improper installation and usage, induction of defect by other products, damage due to collision or tire failure.
For technical support or warranty claims, please contact your authorized LAUNCH dealer or the manufacturer directly.