PowMr BE24-N/BE48-N

Contents

PowMr 24V 48V Battery Equalizer Voltage Balancer User Manual

Model: BE24-N/BE48-N

1. Introduction

The PowMr Battery Equalizer is designed to maintain voltage balance between individual 12V batteries connected in series within a larger battery bank. This device is crucial for extending battery life and improving overall system performance by preventing voltage discrepancies that can occur during charging and discharging cycles.

It is applicable to various 12V battery types, including Lead-Acid (GEL, Flooded, AGM), LiFePo4, NiCd, and NiMH batteries, when used in 24V, 36V, 48V, or any N*12V battery systems.

PowMr Battery Equalizer product overview showing supported battery types and voltages

Figure 1: PowMr Battery Equalizer overview, highlighting compatibility with Lead-Acid, LiFePo4, NiCd/NiMH, GEL/FLD/AGM batteries for 24V/48V systems.

2. Setup and Installation

2.1 Connection Overview

The battery equalizer works by shunting current from a higher voltage battery to a lower voltage battery when a voltage difference of 20mV or more is detected between them. This process continues until the battery voltages are nearly equal, optimizing battery performance and extending its lifespan.

2.2 Wiring Instructions

Please follow these steps carefully to connect the battery equalizer to your battery bank:

  1. Red Cable: Connect to the positive (+) pole of the battery.
  2. Black Cable: Connect to the negative (-) pole of the battery.
  3. White Cable: Connect to the middle connection point between two batteries in series. This can be either a battery's negative pole or positive pole, depending on the specific connection point between the two batteries being balanced.
Close-up of PowMr Battery Equalizer showing LED indicators and connection points

Figure 2: Battery Equalizer interface with LED indicators and connection terminals.

2.3 Battery Bank Configurations

The number of equalizers required depends on your battery bank voltage:

  • 24V System: 1 piece of equalizer (for 2x12V batteries in series).
  • 36V System: 2 pieces of equalizers (for 3x12V batteries in series).
  • 48V System: 3 pieces of equalizers (for 4x12V batteries in series).
Wiring diagram for a 24V battery bank with 2 batteries and one equalizer

Figure 3: Connection diagram for a 24V battery bank (2x12V batteries).

Wiring diagrams for 24V, 36V, and 48V battery banks using multiple equalizers

Figure 4: Various battery bank configurations (24V, 36V, 48V) and corresponding equalizer placements.

Wiring diagram for a 4x12V battery bank and illustration of equalization effect

Figure 5: Example of a 4x12V battery bank connection and the balancing effect before and after use.

3. Operating Instructions

3.1 LED Indicators

The equalizer features LED indicators to provide status information:

  • Balanced Working State Area (A/B):
    • A: Indicates the high voltage group.
    • B: Indicates the low voltage group.
  • Under Voltage Warning Area (A/B):
    • A: Indicates undervoltage in the high voltage area.
    • B: Indicates undervoltage in the low voltage area.
  • LED Power Indicator: Illuminates when the device is powered.
  • LED Switch: Controls the LED indicators.

3.2 Automatic Balancing

Once connected, the equalizer automatically monitors the voltage of the 12V batteries in the series string. When a voltage difference of 20mV is detected, it begins to transfer energy from the higher voltage battery to the lower voltage battery until equilibrium is achieved. This process is continuous and passive, requiring no user intervention.

4. Maintenance

The PowMr Battery Equalizer is designed for low maintenance. To ensure optimal performance and longevity:

  • Keep the device clean and free from dust and debris.
  • Periodically check all cable connections to ensure they are secure and free from corrosion.
  • Ensure the equalizer is installed in a well-ventilated area, away from direct sunlight or excessive heat.

5. Troubleshooting

If you experience issues with your battery equalizer, consider the following:

  • No LED indication: Check if the power cables (red and black) are correctly connected to the battery terminals and that the battery bank has sufficient voltage.
  • Uneven battery voltages persist: Verify that the white cable is correctly connected to the middle point between the two batteries being balanced. Ensure all connections are tight.
  • Device appears damaged: Disconnect the equalizer immediately and contact customer support. Do not attempt to repair the device yourself.

6. Specifications

FeatureSpecification
Model NumberBE24-N/BE48-N
Brand NamePowMr
Battery Nominal Voltage2*12V (balances 12V units)
Output Voltage (V)24V/48V (System Voltage)
Optimizing Current0-5A
Quiescent Current<3mA
Dimensions78mm * 78mm * 28mm
ProtectionReverse Polarity Protection
Low Voltage Disconnect10V
Work Time (h)24 hours
ApplicationHome
CertificationCE

7. User Tips

  • Battery Compatibility: This equalizer is designed to balance individual 12V battery units within a series string. If you are using batteries with a nominal voltage higher than 12V (e.g., 24V LiFePo4 batteries), ensure that the equalizer can be connected to the internal 12V mid-points of these batteries, or consider a different equalizer specifically designed for higher voltage battery units.
  • System Voltage: Always ensure the correct number of equalizers are used for your total battery bank voltage (e.g., 1 for 24V, 2 for 36V, 3 for 48V) to effectively balance all 12V battery units in series.
  • Wiring Accuracy: Double-check all wiring connections (red to +, black to -, white to midpoint) before powering on the system to prevent damage to the equalizer or batteries.

8. Frequently Asked Questions (FAQ)

Q: Can this equalizer be used with 24V LiFePo4 batteries in a 48V system?

A: The PowMr Battery Equalizer is designed to balance individual 12V battery units connected in series. If your 24V LiFePo4 batteries are internally composed of two 12V cells with an accessible mid-point, you might be able to use this equalizer to balance those internal 12V sections. However, if your 24V batteries are treated as single units without accessible 12V mid-points, this equalizer is not suitable. For a 48V system built from 12V batteries, you would typically use three equalizers for four 12V batteries in series.

9. Warranty and Support

For technical support, warranty claims, or further inquiries, please contact PowMr directly:

  • Company: SHENZHEN HEHEJIN INDUSTRIAL CO., LTD
  • Address: Room E, 10th Floor, Building A, Rongde International, Henggang Street, Longgang District, Shenzhen, Guangdong, China 518116
  • Tel/Fax: +86 755-28219903
  • Website: https://powmr.com
  • E-mail: support@powmr.com

A detailed user manual in PDF format is also available for download: PowMr Battery Equalizer User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.