SUMRY MPS VIII ECO

Contents

SUMRY ECO Hybrid Solar Inverter User Manual

Models: 3.6KW, 4.2KW, 6.2KW

1. Introduction

1.1 Purpose and Scope

This manual provides detailed instructions for the assembly, installation, operation, and troubleshooting of your SUMRY ECO Hybrid Solar Inverter. Please read this manual carefully before installation and operation, and keep it for future reference. It includes safety and installation guidelines, as well as information on necessary tools and wiring.

1.2 Key Features

The SUMRY ECO Hybrid Solar Inverter is a multi-function inverter/charger that combines the capabilities of an inverter, solar charger, and battery charger to provide uninterruptible power support. Its compact size and comprehensive LCD display allow for user-configurable and easily accessible button operations.

  • Pure sine wave output for sensitive electronics.
  • Configurable input voltage range for home appliances and personal computers.
  • Configurable battery charging current based on application needs.
  • Configurable AC/Solar Charger priority.
  • Compatibility with mains voltage or generator power.
  • Automatic restart upon AC recovery.
  • Protection against overload, over-temperature, and short circuits.
  • Smart battery charger design for optimized battery performance.
  • Cold start function.
  • Inverter running without battery.
  • High PV input voltage range (60-500VDC).
  • Built-in 120A MPPT Solar charge: max 6200W (for 3.6KW/4.2KW) max 6500W (for 6.2KW).
  • Built-in 80A MPPT Solar charge: max 6500W (for 3.6KW/48V).
  • Dual communication ports for Battery communication and Wifi communication.
  • Dual output.

1.3 Basic System Architecture

This inverter/charger is designed to power various appliances in home or office environments, including motor-type appliances like tube lights, fans, refrigerators, and air conditioners. A complete system typically includes the inverter/charger, a generator or utility power source, PV modules, and external battery packs.

Diagram showing solar power, utility, and generator inputs connected to a solar inverter, which then connects to battery packs and home appliances.
Figure 1: Hybrid Power System Diagram illustrating various power sources and loads.

2. Safety Instructions

WARNING: This chapter contains important safety and operating instructions. Read and keep this manual for future reference.

  1. Before using the unit, read all instructions and cautionary markings on the unit, the batteries, and all appropriate sections of this manual.
  2. Do not disassemble the unit. Take it to a qualified service center when service or repair is required. Incorrect re-assembly may result in a risk of electric shock or fire.
  3. To reduce the risk of electric shock, disconnect all wirings before attempting any maintenance or cleaning. Turning off the unit will not reduce this risk.
  4. CAUTION - Only qualified personnel can install this device with a battery.
  5. NEVER charge a frozen battery.
  6. For optimum operation, follow the required specifications to select appropriate cable sizes.
  7. Be very cautious when working with metal tools on or around batteries. A potential risk exists to drop a tool to spark or short circuit batteries or other electrical parts, which could cause an explosion.
  8. Strictly follow the installation procedure when disconnecting AC or DC terminals. Refer to the INSTALLATION section for details.
  9. One 150A fuse is provided as over-current protection for the battery supply.
  10. GROUNDING INSTRUCTIONS - This inverter/charger should be connected to a permanent grounded wiring system. Comply with local requirements and regulations.
  11. NEVER cause AC output and DC input short circuits. Do NOT connect to the mains when DC input short circuits.
  12. Warning!! Only qualified service persons are able to service this device. If errors persist after following the troubleshooting table, send the inverter/charger back to a local dealer or service center for maintenance.

3. Setup and Installation

3.1 Unpacking and Inspection

Upon receiving your inverter, inspect the unit for any damage. Ensure the package contains the unit and the user manual. If any items are missing or damaged, contact your supplier immediately.

Video: Unboxing and initial setup overview of the SUMRY ECO Hybrid Solar Inverter.

3.2 Preparation and Mounting

Before connecting any cables, remove the screws located under the machine and detach the bottom cover plate. When selecting a mounting location:

  • Do not mount the inverter on flammable construction materials.
  • Mount on a solid surface.
  • Install the inverter at eye level for easy LCD display readability.
  • Allow approximately 20 cm clearance to the sides and 50 cm above and below the unit for proper air circulation and heat dissipation.
  • Ensure the ambient temperature is between 0°C and 55°C for optimal operation.
  • The recommended installation position is vertically adhered to a wall.
  • Ensure sufficient space around the machine for adequate heat dissipation and wiring access.

SUITABLE FOR MOUNTING ON CONCRETE OR OTHER NON-COMBUSTIBLE SURFACE ONLY.

Secure the unit by screwing two M6 screws into the mounting surface.

SUMRY ECO Inverter showing dimensions and communication ports.
Dimensions of the SUMRY ECO Hybrid Solar Inverter (D*W*H: 420*310*110mm) and location of communication ports (BMS RS485, RS232, Wifi).

3.3 Battery Connection

CAUTION: For safety and regulation compliance, install a separate DC over-current protector or disconnect device between the battery and inverter. Always use appropriate cable sizes as specified below.

WARNING: All wiring must be performed by qualified personnel.

  1. Remove 18 mm of insulation from positive and negative conductors.
  2. Use bootlace ferrules on the wire ends with a proper crimping tool.
  3. Connect all battery packs as shown in the diagram (refer to the PDF manual for detailed diagrams for 3.6KW/4.2KW and 6.2KW models).
  4. Insert the battery wires flatly into the battery connectors and tighten the bolts to a torque of 2 Nm in a clockwise direction. Ensure correct polarity (+ to + and - to -) at both the battery and the inverter/charger.

WARNING: Shock Hazard - Installation must be performed with care due to high battery voltage in series.

CAUTION!! Before making the final DC connection or closing the DC breaker/disconnector, ensure positive (+) is connected to positive (+) and negative (-) is connected to negative (-).

Recommended Battery Cable Size
ModelWire SizeCable (mm²)Torque Value (max)
3.6KW/4.2KW/6.2KW1 x 2AWG252 Nm

3.4 AC Input/Output Connection

CAUTION!! Install a separate AC breaker between the inverter and the AC input power source. The recommended AC breaker is 32A for 3.6KW/4.2KW and 50A for 6.2KW. Do NOT mis-connect input and output terminals.

WARNING: All wiring must be performed by qualified personnel. Use appropriate cable sizes as specified below.

  1. Before making AC input/output connections, open the DC protector or disconnector.
  2. Remove 10mm of insulation for six conductors. Shorten phase L and neutral conductor N by 3mm.
  3. Insert AC input wires according to polarities (L=LINE, N=Neutral) and tighten terminal screws.
  4. WARNING: Ensure AC power source is disconnected before hardwiring.
  5. Insert AC output wires according to polarities (L=LINE, N=Neutral) and tighten terminal screws.
  6. Ensure all wires are securely connected.

CAUTION: Appliances like air conditioners require 2-3 minutes to restart. If power fluctuates, the inverter may trigger an overload fault. Check appliance manufacturer for time-delay function.

Suggested Cable Requirement for AC Wires
ModelGaugeCable (mm²)Torque Value
3.6KW/4.2KW12 AWG41.2 Nm
6.2KW10 AWG61.2 Nm

3.5 PV Connection

CAUTION: Install a DC circuit breaker between the inverter and PV modules.

WARNING: Use appropriate cable sizes for PV module connection.

  1. Remove 10mm of insulation from positive and negative conductors.
  2. Use bootlace ferrules on the wire ends with a proper crimping tool.
  3. Check correct polarity of wire connection from PV modules and PV input connectors. Connect positive (+) to positive (+) and negative (-) to negative (-).
Recommended PV Module Cable Size
ModelWire SizeCable (mm²)Torque Value (max)
3.6KW/4.2KW/6.2KW1 x 12AWG41.2 Nm
PV Array Specifications
INVERTER MODEL3.6KW/4.2KW6.2KW
Max. PV Array Open Circuit Voltage500Vdc
PV Array MPPT Voltage Range60Vdc~450Vdc

3.6 Final Assembly

After connecting all wirings, replace the bottom cover by screwing the two screws back into place.

3.7 Communication Connection

The inverter supports Wi-Fi and GPRS cloud communication for monitoring. Use the supplied communication cable to connect to the inverter and the respective module (Wi-Fi or GPRS). Download the APP and follow the quick installation guidelines to set up the network and register the device. The inverter status can then be monitored via the mobile phone APP or a computer webpage.

For lithium battery communication, connect an RJ45 cable between the inverter's BMS communication port and the battery's RS485 communication port. Ensure the PIN definitions correspond (refer to the PDF manual for the PIN definition table). If using a lithium battery, set the battery type to "LIB-485" in program 05 and select the matching battery protocol in program 43.

4. Operating Instructions

4.1 Power ON/OFF

Once the unit is properly installed and batteries are connected, press the On/Off switch (located on the side of the case) to power on the unit.

4.2 Operation and Display Panel

The inverter features an operation and display panel on the front, including three indicators, four function keys, and an LCD display. This panel provides real-time operating status and input/output power information.

Front view of the SUMRY ECO Inverter showing the LCD display and function buttons.
Front view of the SUMRY ECO Hybrid Solar Inverter with LCD display and control buttons.

4.3 LCD Display Icons

The LCD display provides various icons to indicate the inverter's status and operational mode. These include icons for AC input, PV input, configuration programs, fault/warning indicators, output information (voltage, frequency, load), battery information, and overload status. Refer to the PDF manual (section 5.3) for a complete list and description of all LCD display icons.

4.4 LCD Setting

To enter setting mode, press and hold the ENTER button for 3 seconds. Use the UP or DOWN buttons to select setting programs, and ENTER to confirm or ESC to exit. Key settings include:

  • Program 00: Exit setting mode (One-button restore setting options: 00 GOE, 00 GOH).
  • Program 01: Output source priority (Utility first, Solar first, SBU priority, MKS priority).
  • Program 02: Maximum charging current.
  • Program 03: AC input voltage range.
  • Program 05: Battery type (AGM, Flooded, User-Defined, LIB-485).
  • Program 06: Auto restart when overload occurs.
  • Program 07: Auto restart when over temperature occurs.
  • Program 09: Output frequency.
  • Program 10: Output voltage.
  • Program 11: Maximum utility charging current.
  • Program 12: Setting voltage point back to utility source when selecting "SBU priority" or "Solar first" in program 01.
  • Program 13: Setting voltage point back to battery mode when selecting "SBU priority" or "Solar first" in program 01.
  • Program 16: Charger source priority.
  • Program 18: Alarm control.
  • Program 19: Auto return to default display screen.
  • Program 20: Backlight control.
  • Program 22: Beeps while primary source is interrupted.
  • Program 23: Overload bypass.
  • Program 25: Record Fault code.
  • Program 26: Bulk charging voltage (C.V voltage).
  • Program 27: Floating charging voltage.
  • Program 29: Low DC cut-off voltage.
  • Program 30: Battery equalization.
  • Program 31: Battery equalization voltage.
  • Program 33: Battery equalized time.
  • Program 34: Battery equalized timeout.
  • Program 35: Equalization interval.
  • Program 36: Equalization activated immediately.
  • Program 37: GRID-tie operation.
  • Program 38: GRID-tie current.
  • Program 39: LED pattern light.
  • Program 41: Dual output.
  • Program 42: Enter the dual output functional voltage point.
  • Program 43: Lithium battery protocol.
  • Program 44: Delayed grid access.
  • Program 45: Maximum Second Load.

4.5 Operating Mode Description

The inverter operates in various modes, including Standby, Line Mode, Grid-Tie Operation, and Battery Mode. Each mode has specific behaviors regarding power flow and charging. Refer to the PDF manual (section 5.6) for detailed descriptions of each operating mode and their corresponding LCD displays.

4.6 Battery Equalization

The equalization function helps reverse the buildup of negative chemical effects like stratification and removes sulfate crystals from battery plates, optimizing battery performance and longevity. To apply equalization, enable the function in monitoring LCD setting program 30. You can then set the equalization interval in program 35 or activate it immediately in program 36. The controller will enter the Equalize stage when the set interval is reached or immediately if activated.

4.7 Mains and Lithium Battery Activation Function

  • After 90 seconds of mains power connection, the machine connects to the mains and starts working.
  • If the inverter is in lithium battery mode (item 05 is Llb or Llb-485) and the battery is not connected, the mains activation function is automatically enabled upon mains connection.

5. Maintenance

5.1 Anti-Dust Kit Clearance and Maintenance

The inverter comes with a pre-installed anti-dust kit to protect internal components and maintain optimal temperature. This kit helps increase product reliability in harsh environments.

  1. Loosen the screw on the top of the inverter in a counterclockwise direction.
  2. Remove the dustproof case and take out the air filter foam.
  3. Clean the air filter foam and dustproof case.
  4. After cleaning, re-assemble the dust-kit back to the inverter.

NOTICE: The anti-dust kit should be cleaned from dust every one month.

6. Troubleshooting

This section provides guidance for common issues. For persistent problems, contact a qualified service technician.

6.1 Fault Reference Codes

The inverter's LCD display will show specific fault codes if an error occurs. Refer to the PDF manual (section 5.9) for a complete list of fault codes, their events, and corresponding icon displays.

6.2 Warning Indicators

The inverter provides warning indicators for various conditions. These warnings are accompanied by audible alarms and specific icon flashes on the LCD. Refer to the PDF manual (section 5.10) for a complete list of warning codes, events, audible alarms, and icon displays.

6.3 Troubleshooting Table

If you encounter any issues, consult the table below for possible causes and solutions.

Troubleshooting Guide
ProblemLCD/LED/BuzzerExplanation / Possible causeWhat to do
Unit shuts down automatically during startup process.LCD/LEDs and buzzer will be active for 3 seconds and then complete off.The battery voltage is too low (<1.91V/Cell)1. Re-charge battery.
2. Replace battery.
No response after power on.No indication.1. The battery voltage is far too low. (<1.4V/Cell)
2. Internal fuse tripped.
1. Contact repair center for replacing the fuse.
2. Re-charge battery.
3. Replace battery.
Input voltage is displayed as 0 on the LCD and green LED is flashing.Input protector is trippedCheck if AC breaker is tripped and AC wiring is connected well.
Mains exist but the unit works in battery mode.Green LED is flashing.Insufficient quality of AC power. (Shore or Generator)1. Check if AC wires are too thin and/or too long.
2. Check if generator (if applied) is working well or if input voltage range setting is correct. (UPS Appliance)
Green LED is flashing.Set "Solar First" as the priority of output source.Change output source priority to Utility first.
When the unit is turned on, internal relay is switched on and off repeatedly.LCD display and LEDs are flashingBattery is disconnected.Check if battery wires are connected well.
Fault code 07Overload error. The inverter is overload 110% and time is up.Reduce the connected load by switching off some equipment.
Output short circuited.Check if wiring is connected well and remove abnormal load.
Fault code 05Temperature of internal converter component is over 120°C.Check whether the air flow of the unit is blocked or whether the ambient temperature is too high.
Fault code 02Internal temperature of inverter component is over 100°C.Return to repair center.
Buzzer beeps continuously and red LED is on.Fault code 03Battery is over-charged.
The battery voltage is too high.
Check if spec and quantity of batteries are meet requirements.
Fault code 01Fan faultReplace the fan.
Fault code 06/58Output abnormal (Inverter voltage below than 190Vac or is higher than 260Vac)1. Reduce the connected load.
2. Return to repair center
Fault code 08/09/53/57Internal components failed.Return to repair center.
Fault code 51Over current or surge.Restart the unit, if the error happens again, please return to repair center.
Fault code 52Bus voltage is too low.
Fault code 55Output voltage is unbalanced.

7. Specifications

The following tables detail the technical specifications for the SUMRY ECO Hybrid Solar Inverter.

7.1 General Specifications

Table 6: General Specifications
INVERTER MODEL3.6KW4.2KW6.2KW
Safety CertificationCE
Operating Temperature Range-10°C to 50°C
Storage temperature-15°C~60°C
Humidity5% to 95% Relative Humidity (Non-condensing)
Dimension (D*W*H), mm358×442×116
Net Weight, kg8.08.08.9
Output Current10A
Is Smart DeviceYes
Output TypeSINGLE
Communication InterfaceRS232
Support Battery typelithium battery, LiFePo4; Lead acid battery
Control typeMPPT
Continuous Power3000W
AC output voltage110/220V-50Hz/60Hz
WaveformPure Sine Wave
AC input230VAC
Battery voltage24VDC/48VDC
Max charge current for battery60A
Max charge current for solar80A

7.2 Line Mode Specifications

Table 1: Line Mode Specifications
INVERTER MODEL3.6KW4.2KW6.2KW
Input Voltage WaveformSinusoidal (utility or generator)
Nominal Input Voltage230Vac
Low Loss Voltage170Vac±7V (UPS); 90Vac±7V (Appliances)
Low Loss Return Voltage180Vac±7V (UPS); 100Vac±7V (Appliance)
High Loss Voltage280Vac±7V
High Loss Return Voltage270Vac±7V
Max AC Input Voltage300Vac
Nominal Input Frequency50Hz / 60Hz (Auto detection)
Low Loss Frequency40±1Hz
Low Loss Return Frequency42±1Hz
High Loss Frequency65±1Hz
High Loss Return Frequency63±1Hz
Output Short Circuit ProtectionCircuit Breaker
Efficiency (Line Mode)>95% (Rated R load, battery full charged)
Transfer Time10ms typical (UPS); 20ms typical (Appliances)

7.3 Inverter Mode Specifications

Table 2: Inverter Mode Specifications
INVERTER MODEL3.6KW4.2KW6.2KW
Rated Output Power3.6KW4.2KW6.2KW
Output Voltage WaveformPure Sine Wave
Output Voltage Regulation230Vac±5%
Output Frequency50Hz
Peak Efficiency93%
Overload Protection3s@≥150% load; 5s@101%~150% load
Surge Capacity2* rated power for 5 seconds
Nominal DC Input Voltage24Vdc48Vdc
Cold Start Voltage23.0Vdc46.0Vdc
Low DC Warning Voltage @ load < 50%22.0Vdc44.0Vdc
Low DC Warning Voltage @ load ≥ 50%21.0Vdc42.0Vdc
Low DC Warning Return Voltage @ load < 50%22.5Vdc45.0Vdc
Low DC Warning Return Voltage @ load ≥ 50%22.0Vdc44.0Vdc
Low DC Cut-off Voltage @ load < 50%20.5Vdc41.0Vdc
Low DC Cut-off Voltage @ load ≥ 50%20.0Vdc40.0Vdc
High DC Recovery Voltage32Vdc62Vdc
High DC Cut-off Voltage33Vdc63Vdc
No Load Power Consumption30W35W50W

7.4 Two Load Output Power

Table 3: Two Load Output Power
INVERTER MODEL3.6KW4.2KW6.2KW
Full Load3600W4200W6200W
Maximum Main Load3600W4200W6200W
Second Load Range720W~2520W840W~2940W1240W~4340W
Main Load Cut Off Voltage22VDC44VDC
Main Load Return Voltage26VDC52VDC

7.5 Charge Mode Specifications

Table 4: Charge Mode Specifications
Utility Charging Mode
INVERTER MODEL3.6KW4.2KW6.2KW
Charging Algorithm3-Step
AC Charging Current (Max)100Amp (@VI/P=230Vac)
Bulk Charging Flooded Battery29.258.4
Voltage AGM / Gel Battery28.256.4
Floating Charging Voltage27Vdc54Vdc
MPPT Solar Charging Mode
INVERTER MODEL3.6KW4.2KW6.2KW
Max. PV Array Power6200W6500W
Nominal PV Voltage240Vdc360Vdc
PV Array MPPT Voltage Range60Vdc~500Vdc
Max. PV Array Open Circuit Voltage500Vdc
Max Charging Current (AC charger plus solar charger)120Amp120Amp120Amp

7.6 Grid-Tie Operation

Table 5: Grid-Tie Operation
INVERTER MODEL3.6KW4.2KW6.2KW
Nominal Output Voltage220/230/240 VAC
Feed-in Grid Voltage Range195~253VAC
Feed-in Grid Frequency Range50±1Hz/60±1Hz
Nominal Output Current15.7A18.2A26.9A
Power Factor Range>0.99
Maximum Conversion Efficiency (DC/AC)97%

7.7 Approximate Back-up Time Table

The following tables provide approximate backup times based on load and battery capacity. Note that actual backup time depends on battery quality, age, and type, and may vary between manufacturers.

Backup Time @ 24Vdc (100Ah & 200Ah)
ModelLoad (W)Backup Time @ 24Vdc 100Ah (min)Backup Time @ 24Vdc 200Ah (min)
3.6KW/4.2KW3004491100
600222525
900124303
120095227
150068164
180056126
210048108
24003594
27003174
32002867
36002560
42002253
Backup Time @ 48Vdc (100Ah & 200Ah)
ModelLoad (W)Backup Time @ 48Vdc 100Ah (min)Backup Time @ 48Vdc 200Ah (min)
6.2KW5006131288
1000268613
1500158402
2000111271
250090215
320076182
350065141
400050112
450044100
50004090
62003680

8. User Tips

  • Prioritizing Solar/Battery: The inverter is often configured as a no-break system by default. To prioritize solar power and battery usage, and only use utility grid power as a last resort, you will need to adjust the settings in the LCD menu (refer to section 4.4 LCD Setting, Program 01: Output source priority).
  • Terminal Connections: Some users have noted that the terminals, especially for solar panels, can be soft or difficult to tighten. Exercise care during connection to ensure secure and firm wiring.
  • Manual Language: The primary manual is in English. If you require instructions in another language, please check for translated versions or consult online resources.

9. Warranty and Support

For detailed warranty information and further support, please refer to the official user manual PDF available at SUMRY ECO Hybrid Inverter User Manual (PDF). This document contains comprehensive details regarding product guarantees and service procedures.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.