1. Introduction
Thank you for choosing the SIYI ZR10 Gimbal Camera. This manual provides essential information for the safe and effective use of your device. The SIYI ZR10 is a high-performance 2K 4MP QHD camera featuring 30X hybrid zoom (10X optical zoom), HDR, starlight night vision, and a 3-axis stabilizer, designed for UAV, FPV, UGV, and USV applications.
2. Safety Information
- Recreational Use Only: This product is intended for recreational use.
- Prohibited Modifications: Illegal modification of drones/planes or this camera is strictly prohibited.
- Legal Compliance: Always adhere to the relevant laws and regulations regarding the use of drones/planes and camera equipment in your country or region to ensure legal operation.
3. Package Contents
Please check the package contents upon unboxing:
- SIYI ZR10 Gimbal Camera Unit
- Necessary connection cables (specific types may vary, refer to packaging)
4. Setup
4.1 Product Interface Overview
Familiarize yourself with the various ports and indicators on the SIYI ZR10 Gimbal Camera:

Figure 1: SIYI ZR10 Gimbal Camera Product Interface and Wiring Diagram. This diagram illustrates the location of each port and the pinout configurations for power, control, and video/protocol connections.
- Power Input (3S to 6S): Main power supply connection.
- Control Signal Input & Output (S.Bus / UART): For flight controller communication and gimbal control.
- Ethernet: Provides Ethernet video stream and SDK protocol control.
- Type-C: Used for firmware upgrades and configuration.
- TF Card Slot: For file storage (video recordings, photos) and data copy.
- Status Indicator: Provides visual feedback on the camera's operational status.
Caution: Early manufacturing lots support 3S to 4S power input only. Please carefully confirm the power requirements for your specific unit before connecting.
4.2 Wiring Connections
Ensure correct wiring according to the pinout diagrams below:
| Connection Type | Pinout (Left to Right) |
|---|---|
| Video & Protocol | S.BUS IN, GND, RX, TX, GND, 5V, GND, 5V |
| Gimbal Control | S.BUS IN, GND, 5V, GND |
| Power | GND, 5V, GND, 5V |
5. Operating Instructions
5.1 Powering On/Off
- Power On: Connect the appropriate power source (3S-6S LiPo battery, verify compatibility) to the Power Input port. The status indicator will illuminate.
- Power Off: Disconnect the power source.
5.2 Basic Operation
- Gimbal Control: Control the gimbal's pan, tilt, and roll via your flight controller's remote control system, connected through the Control Signal Input & Output port.
- Video Output: Access the video stream via the Ethernet port for real-time monitoring.
- Recording: Insert a TF card into the TF Card Slot. Use the control interface (e.g., via SDK or connected device) to start and stop video recording or capture photos.
- Zoom Control: Utilize the remote control or SDK commands to adjust the 10X optical zoom and 30X hybrid zoom capabilities.
6. Maintenance
- Cleaning: Use a soft, dry cloth to clean the camera lens and body. Avoid using harsh chemicals or abrasive materials.
- Storage: Store the camera in a cool, dry place away from direct sunlight and extreme temperatures. Use a protective case to prevent physical damage.
- Firmware Updates: Periodically check the official SIYI website for firmware updates to ensure optimal performance and access to new features. Update via the Type-C port.
7. Troubleshooting
- No Power: Ensure the power source is correctly connected and within the specified voltage range (3S-6S, or 3S-4S for early models). Check all cable connections.
- No Video Output: Verify Ethernet cable connection. Ensure the receiving device is properly configured to receive the video stream.
- Gimbal Not Responding: Check the S.Bus/UART connection to the flight controller. Ensure the flight controller is sending correct control signals and the gimbal is properly initialized.
- Recording Issues: Ensure a compatible TF card is inserted and has sufficient free space. Check card formatting (usually FAT32 or exFAT).
8. Specifications
| Feature | Detail |
|---|---|
| Model Number | ZR10 |
| Compatible Drone Brand | YUNEEC (Compatibility) |
| Compatible Drone Model | UAV/FPV |
| Video Resolution | 2.7K |
| Effective MegaPixel | < 8MP |
| Sensor Size | 2/3 inches |
| Size | 18X13.5X9CM |
| Weight | 1KG |
| Package | Yes |
| Origin | Mainland China |
| Certification | CE |
| High-concerned chemical | None |
9. User Tips
No specific user tips are available from the provided data.
10. Compliance and Disclaimer
This product is intended for recreational use only. Any illegal modification of drones/planes or this camera is strictly prohibited. Users are responsible for understanding and complying with all relevant local and national laws and regulations concerning the operation of drones and camera equipment.
11. Warranty and Support
The SIYI ZR10 Gimbal Camera typically comes with a 1-Year Warranty from the date of purchase. For warranty claims, technical support, or further inquiries, please contact your retailer or visit the official SIYI website for detailed support information and contact channels.