SEamopar 433Mhz

Contents

SEamopar 433 MHz Universal Remote Control Duplicator

User Instruction Manual

1. Introduction

Thank you for choosing the SEamopar 433 MHz Universal Remote Control Duplicator. This device is designed to copy codes from existing 433 MHz remote controls, allowing you to operate various systems such as garage doors, automatic gates, electronic rolling gates, and alarm systems. This manual provides detailed instructions for programming, operation, and maintenance.

Please note: This remote is a replacement remote, not an original. Read this manual carefully before programming.

Four SEamopar remote controls in green, yellow, red, and blue, each with four buttons (A, B, C, D) and a metal keychain clip.

Figure 1: SEamopar 433 MHz Universal Remote Control Duplicators

2. Safety Information

WARNING: To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door:

  • ALWAYS keep remote controls out of reach of children.
  • NEVER permit children to operate or play with remote controls.
  • Activate gate or door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel.
  • ALWAYS keep gate or garage door in sight until completely closed.
  • NEVER permit anyone to cross the path of a moving gate or door.

WARNING: Battery Safety Information:

  • NEVER allow small children near batteries.
  • If a battery is swallowed, immediately notify a doctor.
  • To reduce the risk of fire, explosion, or chemical burn, replace ONLY with 3V CR2032 batteries.
  • DO NOT recharge, disassemble, heat above 212° F (100° C), or incinerate batteries.

3. Setup and Programming

This remote control can be used as a replacement for various remote controls, including 80 Series, 970 Series, and 370 Series. It is compatible with 315 MHz or 390 MHz garage door openers manufactured after January 1, 1993. Ensure your garage door opener has a working light bulb, as it acts as a programming indicator.

To successfully duplicate a remote, ensure the following conditions are met:

  1. Your original remote control can be used normally.
  2. You know the original remote control's firing frequency.
  3. You know the remote control's code chip type.
Internal circuit boards of three remote controls showing batteries, buttons, and chips with frequency markings like LR433T2 and 30.000 MHz.

Figure 2: Internal components showing frequency and chip details

Programming Steps:

  1. Prepare the Remote: Press and hold buttons 'II' and 'III' (typically 'B' and 'C' or 'C' and 'D' on a 4-button remote) simultaneously until the LED on the front of the remote control turns on, then flashes 4 times, and finally turns off. This clears the remote for new programming.
  2. Select Opener Type: Press and release the button on the duplicator remote you wish to program a specific number of times corresponding to your garage door opener type:
    • 1 Press: Security+ 2.0™ (Yellow Learn Button)
    • 2 Presses: 315 MHz Security+ (Purple Learn Button)
    • 3 Presses: 390 MHz Security+ (Red/Orange Learn Button)
    • 4 Presses: 390 MHz Billion Code (Green Learn Button)
  3. Exit Programming Mode: To exit this programming mode, press any remote control button EXCEPT the button you just programmed in the previous step.
  4. Activate Learn Mode on Opener: Locate the 'Learn' button on your garage door opener (refer to your opener's manual if needed). Press and release this 'Learn' button. The 'Learn' LED on the opener will light up. You have approximately 30 seconds to complete the next step.
  5. Pair Remote with Opener: Press the button on the duplicator remote that you programmed in Step 2. Continue pressing until the garage door opener lights flash or two clicks are heard. This indicates successful pairing.
  6. Test the Remote: Press the newly programmed button on your duplicator remote. The garage door opener should activate.
  7. Install Visor Clip (if applicable): If your model includes a visor clip, install it for convenient use.

If programming is not successful, please repeat Step 1 and Step 2 carefully.

4. Operating Instructions

Once programmed, your SEamopar remote control is ready for use:

  • Activation: Press and hold the desired button on the remote control until the door or gate starts to move. Do not release the button immediately after pressing.
  • Range: The remote control typically operates from up to 3 car lengths away, depending on environmental factors and the receiver's sensitivity.
  • Multiple Devices: Additional buttons on the remote control can be programmed to operate up to 3 other devices, such as additional garage door openers, light controls, gate operators, or access control systems.
Black remote control with 'Application' text and circular images showing a garage door, an automatic glass door, and an alarm light.

Figure 3: Common applications for the remote control

5. Maintenance

Battery Replacement

The LED(s) on your remote control will flash when the battery is low and needs to be replaced. To replace the battery, follow these steps:

  1. Open the Case:
    • For models similar to J893MAX: Pry open the case first in the middle, then at each side (2 and 3) using a small tool or the visor clip.
    • For models similar to J890MAX: Pry open the case with a screwdriver blade.
  2. Replace Battery: Carefully remove the old battery. Insert a new 3V CR2032 coin cell battery with the positive side (+) facing up.
  3. Close Case: Snap the remote control case back together securely.
  4. Dispose of Old Battery: Dispose of the old battery properly according to local regulations.

6. Troubleshooting

  • Remote Not Programming: Ensure your original remote is functional, you know its frequency, and the code chip type. Double-check that you are pressing the correct number of times for your opener type (Step 2 of programming). If issues persist, repeat the programming steps from the beginning.
  • Remote Not Activating Opener: Check if the remote's LED flashes when a button is pressed. If not, the battery might be dead or incorrectly installed. Replace the battery if necessary. Ensure the remote is within operating range.
  • Interference: Strong radio frequency interference can affect the remote's range and performance. Try operating the remote from a different location.

7. Specifications

Brand NameSEamopar
Model Number433Mhz
Frequency433 MHz
Channel4
Wireless CommunicationRF
UseElectric Door (Garage Door, Automatic Door, Alarm, Electronic Rolling Gates, Retractable Doors)
Support APPNo
PackageYes
OriginMainland China
CertificationNONE
High-concerned chemicalNone

8. User Tips

  • Always keep your original remote control in a safe place, as it is needed for duplicating.
  • When programming, ensure you are close to the garage door opener to ensure a strong signal for the 'Learn' function.
  • If you have multiple openers, you can program different buttons on the duplicator remote to control each one, provided they operate on compatible frequencies.

9. Warranty and Support

For any issues or questions not covered in this manual, please contact your retailer or the manufacturer's customer support. Keep your purchase receipt for warranty claims.

© 2024 SEamopar. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.