1. Product Introduction
The CX1000AM is a compact serial port controlled voice playback module designed for various applications. It supports MP3 and WAV decoding formats and operates on a wide voltage power supply of 3.3V to 5.2V DC. The module features an onboard 5W Class D amplifier capable of directly driving 4-8Ω speakers (3W-5W recommended) and includes 32Mbits (4MBytes) of flash memory for audio storage. Audio files can be easily replaced by connecting the module to a computer via a USB cable, where it appears as a USB flash drive.

2. Setup and Installation
2.1 Physical Dimensions
The CX1000AM module features a compact design with a standard 2.54mm spacing stamp hole for easy integration into projects.

2.2 Pin Definitions and Interface
The module provides various pins for power, audio output, UART communication, and USB data. Refer to the diagram and table below for detailed pin descriptions.


| Pin | Name | Description |
|---|---|---|
| 1 | DACL | Left channel audio signal output |
| 2 | DACR | Right channel audio signal output |
| 3 | BUSY | Play state, output 3.0V while playing, otherwise 0V |
| 4 | USB_DP | DP of USB port |
| 5 | USB_DM | DM of USB port |
| 6, 7 | GND | Ground |
| 8 | VCC_5V | Power supply by 3.3-5.2VDC, 3.7V recommended |
| 9 | UART_TX | UART TXD |
| 10 | UART_RX | UART RXD |
| 11 | SPK- | Speaker negative output |
| 12 | SPK+ | Speaker positive output |
2.3 Power Supply
The module requires a 3.3V to 5.2V DC power supply. A 3.7V power supply is recommended for optimal performance.
2.4 Speaker Connection
The onboard 5W Class D amplifier can directly drive 3W to 5W speakers with an impedance of 4-8Ω.

2.5 Module Variants
The CX1000AM module is available in variants with or without pre-welded pins.


3. Operating Instructions
3.1 Changing Voice Files via USB
The CX1000AM module has 32Mbit (4MBytes) of onboard flash memory. You can easily replace audio files by connecting the module to a computer using a USB cable. The module will appear as a standard USB flash drive.
- Connect the CX1000AM module to your computer using a Type-C USB cable.
- The module will be recognized as a USB flash drive.
- Copy your desired MP3 or WAV audio files into the module's storage.
- Important: Audio files must be renamed using a five-digit number format (e.g.,
00001.mp3,12345.mp3, up to65535.mp3).

3.2 Audio Storage Format
The module supports specific naming conventions and storage methods for audio playback, including combined playback options.

3.3 Serial Port Control (UART)
The CX1000AM supports UART asynchronous serial port control at TTL level. This allows for advanced control over playback functions such as play, pause, track navigation, volume adjustment, EQ mode switching, and specified path playback.
The following tables detail the control commands and their parameters:


For advanced debugging and serial communication, specialized software can be used:

4. Maintenance
To ensure the longevity and proper functioning of your CX1000AM module, follow these general maintenance guidelines:
- Keep the module in a dry environment, away from moisture and extreme temperatures.
- Avoid exposing the module to static electricity, which can damage electronic components.
- Handle the module with care, especially when connecting or disconnecting wires, to prevent damage to the pins or PCB.
- Regularly check connections for looseness or corrosion.
5. Troubleshooting
If you encounter issues with your CX1000AM module, consider the following:
- No Power: Ensure the power supply is within the 3.3V-5.2V DC range and correctly connected to the VCC_5V and GND pins.
- No Audio Output: Verify that speakers are correctly connected to SPK+ and SPK- pins and that the speaker impedance is 4-8Ω. Check that audio files are correctly loaded and named (e.g.,
00001.mp3). - Module Not Recognized by PC: Ensure the Type-C USB cable is functional and properly connected. Try a different USB port or cable.
- Serial Control Issues: Double-check UART connections (TX, RX, GND) and ensure your serial communication software settings (baud rate, data bits, parity, stop bits) match the module's requirements. Refer to the command tables for correct command formats.
- Corrupted Audio: Re-upload audio files to ensure they are not corrupted and follow the specified naming convention.
6. Specifications
Detailed technical specifications for the CX1000AM Voice Chip Module:

| Parameter | Value |
|---|---|
| Electricity (Power Supply) | 3.3~5.2VDC (3.7V recommended) |
| Format Support | MP3, WAV decoding (max audio file sampling rate up to 48KHz) |
| Serial Control | UART asynchronous serial port control (TTL level) for playback, pause, track navigation, volume, EQ mode, song selection, specified path playback/insertion. |
| Amplifier | 5W Class D amplifier (direct drive 3W~5W speakers) |
| Storage Method | 32Mbits (4MBytes) flash memory |
| Transmission | Connects to computer via USB cable to replace audio files |
| Appearance | Standard 2.54mm spacing stamp hole design, easy to install |
| Dimensions | 28mm * 23mm |
7. User Tips
- The CX1000AM module is highly versatile and can be integrated into a wide range of DIY projects requiring custom voice prompts or audio playback. Its compact size and easy file replacement make it suitable for various embedded applications.
- Consider purchasing the module as part of a suite that includes a speaker and a USB-to-UART converter (like CX-340) for a complete setup, as shown in Figure 14.

8. Warranty and Support
For any technical assistance, warranty claims, or further inquiries regarding the CX1000AM Voice Chip Module, please contact the seller or manufacturer directly. Refer to your purchase documentation for specific contact information.
An official user manual in PDF format is available for download: Download User Manual (PDF)