1. Introduction
This manual provides important information for the safe operation, installation, and maintenance of your TiESFONG RX4C-WB Multi-Channel Dash Cam. Please read it carefully and completely before using the product.

Figure 1: TiESFONG RX4C-WB Dash Cam with its components.
2. What's in the Box?
Your TiESFONG RX4C-WB Dash Cam package includes the following items:
- A. TIESFONG RX4C-WB Dash Cam: The main unit of the dash cam.
- B. Rear Camera with cable (18 ft): For recording the rear view of your vehicle.
- C. TIESFONG P7 Hardwire Kit (8.53 ft): For connecting the dash cam directly to your car's power supply for continuous power.
- D. Fuse Connecting Cable (0.98 ft): Used for connecting to the fuse box.
- E. Type-C USB Backup Cable (1.97 ft): For data transfer or alternative power.
- F. Accessories: Additional small parts.
- G. User Manual: This instruction booklet.
- H. Micro SD Card (Optional): For storing video recordings. (Please use a genuine Class 10, U3 card, 64G-256G recommended).
- I. L.R Camera with cable (Optional): External left and right cameras for wider coverage.

Figure 2: Contents of the 1-channel RX4C-WB Dash Cam package.
3. User Reminder and Precautions
3.1 About Security
- Read this 'User Manual' carefully for safety, operating, and maintenance instructions.
- Follow all safety precautions to prevent damage due to improper use.
- Avoid extended exposure to direct sunlight or extreme temperatures (-20℃ to 65℃) to prevent degradation or damage.
- Do not attempt to open or repair the device yourself. Contact the seller for assistance.
- Use the dash cam as intended. Do not use it in ways that are illegal, physically damaging, or dangerous to vehicle occupants.
- Do not operate or install the dash cam while driving, or attempt to change settings.
- Do not connect the uninterruptible power supply without authorization; consult a professional for installation.
- Stop using or remove the dash cam when cleaning or repairing the car.
- Do not install the dash cam in a location that obstructs or reduces the driver's view. Ensure compliance with local vehicle codes.
3.2 About Precautions on Usage
- Before installation, check all accessories for correctness and completeness.
- Format the micro SD card before first use to ensure proper function.
- During installation, ensure the car key is not in the power supply. Do not insert or remove accessories (micro SD card, rear cam) when the dash cam is powered on. Perform these actions when power is off.
- The dash cam screen is for preview only, not original views. For best viewing, plug the memory card into a computer. Turn off the dash cam before removing the memory card.
- Examine, check, and verify the dash cam and memory card at least every 3 months to ensure proper video reception and recording. Verify normal operation of the unit, visible lights, and audible sounds before each use.
- If the Viidure APP cannot connect for preview on some mobile phones, turn on airplane mode and try again.
3.3 About Memory Card
- Use a genuine micro SD card (64G-256G) of Class 10, U3 Speed or above. LEXAR High Endurance TF cards are recommended.
- Insert or remove the micro SD card only when the dash cam is turned off.
- Do not remove the card while recording to prevent loss of important video files.
- Format new cards on the dash cam before use. The 'Format' option is in the dash cam menu.
- Replace damaged or deteriorated memory cards immediately.
- Format the micro SD card once a month to maximize its lifetime.
4. Product Information
4.1 Camera Overview

Figure 3: Dash Cam with 4-inch Touch Screen.
| No. | Name | Description |
|---|---|---|
| 1 | L.R CAM | Jack slot of Type-C for connect with L.R Cam |
| 2 | REAR | Jack slot of 2.5mm round hole for connect with Rear Cam |
| 3 | GPS | Jack slot of 2.5mm round hole for connect with GPS Cable |
| 4 | POWER | Type-C USB port for Power Cable |
| 5 | R | The 'reset' port - Forces the recorder to return to factory settings |
| 6 | TF Card Slot | For inserting TF Card (Micro SD Card) |
| 7 | Indicator Light | 1. Pink light is always bright means powered on (but not recording) 2. Pink light blinking means recording is in progress |
| 8 | Radar Switch & Radar Working Light | Controls radar parking monitor and indicates its status. |
| 9 | Radar Sensor | Sensing moving objects after the car power off. |
| 10 | Bracket | Removable 3M adhesive bracket |
| 11 | Front Cam | Front Facing Camera for video recording road events (tear off protective film before use) |
| 12 | Radar Sensor Light | Indicates radar detection. |
| 13 | OK Button | Confirm function (differs per page) |
| 14 | Down Button | Navigation / Take photo (differs per page) |
| 15 | Up Button | Navigation / Trigger emergency lock (differs per page) |
| 16 | M Button | Menu / Playback (differs per page) |
| 17 | Power Button | Short press: Open/Close screen; Long press: Power ON/OFF |
5. Installation
5.1 Install Memory Card
- Insert a new Micro SD card into the card slot and then power on the dash cam.
- After the dash cam is turned on, press the M button to enter the Settings page.
- In the Setting page, press the V button to switch to the option of 'Format', and press the OK button to enter.
- Then select the 'YES' option and press the OK button to confirm formatting.
- A blue frame will appear: "Formatting, please wait...". Please be patient.
- When formatting is complete, 'Formatting completed!' will be displayed. Press the M button to return to the recording interface. The dash cam will automatically start recording.
Important Notes on Formatting:
- Ensure the screen shows 'completed' or 'failed' during formatting.
- The dash cam will periodically remind you to format the memory card. Files will not be deleted automatically if formatting is not performed.
- Avoid using bad or low-speed memory cards to prevent recording issues.
- Before formatting, save any important videos from the memory card.
5.2 Install Dash Cam onto Car Windshield
5.2.1 Suggested Installation Location
Before installation, power on the dash cam and check the recording angle of the front and interior lenses through the recording view to ensure they are appropriate.
5.2.2 About Electrostatic Stickers
Electrostatic stickers protect your car windshield or window film.
- Confirm the installation position, then wipe the area with screen cleaning paper.
- Tear off the protective film and stick it on the selected position.
- Use a scraper to remove air bubbles between the sticker and the glass.
PS: Stick it on a flat surface without air bubbles for firm adhesion!
5.2.3 About Install the Bracket
- Align the mount with the dash cam mount interface and push it from right to left until installed.
- Tear off the red protective film on the 3M Stick Bracket.
- Attach the bracket to the Electrostatic Sticker, press for 10-20 seconds to ensure a firm fit.
PS: Press firmly and check from outside the car to confirm it's fully fitted!
5.3 Install Power Cord
5.3.1 Connecting the Hardwire Kit's BMW connector
There are two ways to connect the Hardwire Kit's BMW connector:
- To the Fuse Box:
- Ensure the 3-core Fuse Connecting Cable is fully connected to the P7 Hardwire Kit.
- Connect the fuse wire to the corresponding connector in your car's fuse box. Find your car's fuse box location as it varies by model.
- To the OBD connector (Optional, not included):
- If using an OBD Connecting Cable (purchased separately), connect the two sections of the power cable.
- Plug the OBD connector into the OBD socket underneath the driver's seat. Find your car's OBD socket location as it varies by model.
Note: The standard package includes a three-core fuse connecting cable, not an OBD connector cable.
5.3.2 Connecting the Hardwire Kit to Dash Cam
- Connect the TYPE-C USB port of the hardwire kit to the power port of the dash cam.
- Tape the black box of the hardwire kit to the top of the car's front windshield.
- Use a pry bar to carefully run the power cord along the slit on the edge of the windshield and hide it inside the car slit.
- Start your car; the dash cam will auto power on and start recording.
5.3.3 Power Cable of Rear Cam
- Confirm the BMW 4/5-pin connector between the Rear Cam Cable and Power Cable is fully connected.
- Insert the 2.5mm round hole interface of the Rear Cam into the 'Rear' jack slot of the dash cam.
- Use a pry bar to run the power cord along the roof gap and hide it up to the rear windshield inside the car.
- Confirm the Rear Cam position, tear off its protective film, and stick it on.
PS: It is recommended to select a position close to the center of the rear windshield, avoiding the defogging line, to prevent affecting the video effect.
Note: The rear cam is not waterproof and must be mounted inside the car, not on the front.
5.4 About Fuse
5.4.1 Learn about car fuse slot
Based on each fuse slot, the side with the tab is the positive pole (+). Use a circuit test pen to identify the positive pole (+) of the fuse slot. Connect the positive (+) terminal of the power cord to the positive pole (+) of the fuse slot.
TIP: If the hardwire kit does not provide power, try inserting the fuse tap in the OPPOSITE direction.
5.4.2 Installation of Fuse Box
- Locate your fuse box using your owner's manual (usually under the driver's side).
- Find the correct fuse slot using the fuse map.
- Connect to car fuse box:
- Remove the key from the ignition before installation.
- Use a fuse puller or pliers to gently remove the identified fuse.
- Use a circuit tester or multimeter to test if a fuse is an ACC slot or BAT+ slot.
- Select the fuse power cord that matches your fuse slot specifications.
- Remove the original fuse from its slot and insert it into the bottom slot of the fuse you have sized.
- Insert the power cord into the fuse in the correct orientation.
5.4.3 Wiring for ACC Box (Connect with Red Wire)
Connect the Red Wire of the hardwire kit to the positive pole of the ACC fuse slot. The ACC fuse slot energizes only when the ignition switch is on. Test by checking if a tester bulb lights when the engine is on and turns off when the engine is off.
5.4.4 Wiring for BAT+ Box (Connect with Yellow Wire)
Connect the Yellow Wire of the hardwire kit to the positive pole (BAT+) of the constant fuse slot. This interface requires a constant current below 15A and no other equipment using electricity. Test by using a voltage tester to ensure electricity is present even when the car engine is off.
5.4.5 Test your installation
- Connect the power cable to the Dash Cam to ensure it powers on and works normally.
- Hide any extra cables.
6. Basic Operation
6.1 Power ON/OFF
The dash cam automatically turns on when plugged into the power cable and the vehicle starts. It powers off if the power cable is disconnected or the vehicle is turned off. You can also manually power it ON or OFF by long-pressing the Power button.
6.2 WiFi Function
6.2.1 WiFi Function Instructions
- Scan the QR code on your mobile phone to download the Viidure APP or search for "viidure" in your app store.
- The WiFi Name (SSID) is: Tiesfong_Cam_XXXX (WIFI Serial Number).
- The initial WiFi password (PWD) is: 12345678.
6.2.2 WiFi Connection Steps
- Turn on the WiFi function of the dash cam (long press the Power button for 3 seconds on the Recording page).
- On your phone, go to WLAN settings and find "Tiesfong_Cam_XXXX".
- Enter the password to connect.
- Open the 'Viidure' APP to connect.
PS: It is not recommended to modify the WiFi Name. If you need to modify the WiFi password, do so in the APP settings. If the SSID is not found, restart WLAN and swipe the 'NETWORKS' list.
6.3 View Playback On Computer
6.3.1 Folders in the memory card
- 'Event': Lock video files (protected by Gravity Sensor or manual lock). These are not overwritten by auto-loop and need manual deletion or card formatting.
- 'Normal': Normal recorded video files.
- 'Park': Parking monitoring video files (currently no function).
- 'Photo': Photos captured by the recorder.
PS: Video files are saved in 'Video' folder. Regularly clean 'Event' folder to prevent space issues and prolong card life.
6.3.2 Computer View File Description
- Remove the Micro SD card from the dash cam and insert it into a Card Reader.
- Connect the Card Reader to your computer's USB port.
- Install necessary software (e.g., GXPlayer) for MP4 video and JPG photo formats.
- Select the equivalent folder to view videos.
- After viewing, reinsert the memory card into the dash cam. (Do not format on the computer).
6.3.3 About Backup Files
To store important videos or photos long-term, copy them from the memory card to a computer. Do not create new folders on the memory card, as this reduces effective storage space.
6.4 GPS Function
6.4.1 GPS Status
If the GPS signal is not connected, it will display "No locate". If successful, it will display "Has been positionin". The signal column will be displayed below when connected or has signal. The signal channels do not necessarily need to be full or have values to work.
6.4.2 GPS Data Display
- After successful GPS positioning, Speed will be displayed in the lower right corner of the dash cam's recording page.
- Speed, Latitude & Longitude will display in the lower left corner of the recorded video.
6.4.3 Check GPS Data on APP
- For Android: Download the offline map first (More > APP Settings > Offline Map).
- Select and download the video you want to view.
- After downloading, click on the local album in the APP.
PS: After downloading, disconnect your phone from the dash cam to view the track. Keep your phone connected to the Internet as the track needs to read Gaode map packet.
6.4.4 Check GPS Data on Computer
- Remove the Micro SD card and insert it into a Card Reader.
- Connect the Card Reader to the computer.
- In the memory card's root folder, find the "GXPlayer" software.
- Set up the software the first time you use it (Settings button in the upper right corner).
- Drag the video file into the software to view corresponding GPS tracking information.
PS: Stop playing the video before changing map settings in GXPlayer.
6.5 Radar Parking Monitor

Figure 4: Built-in 360° Radar Parking Monitor.
6.5.1 P7 Hardwire Kit
Low-Vol Protection Control buttons: Settable Gears: 11.8V / 12.0V / 12.2V. Select the appropriate low voltage protection value based on your car's voltage. General recommended setting: 11.8V. If the car battery voltage drops below the set value, the power supply will be cut off to protect the battery.
Smart Tip Light: While the P7 hardwire kit is working, it detects car voltage and displays it with a smart alert light. Green light indicates voltage is above the set low-voltage protection, and the Dash Cam will always be in working condition. Red light indicates voltage is below the set protection, and the Dash Cam will power OFF.
TIP: If there's a red light, get proactive attention and deal with it urgently!
6.5.2 Radar Parking Monitor
The dash cam has a built-in 360° sensor radar with dual radar modules, sensing a range of 1m to 1.5m around the car.
- Radar Working Light: Indicates if the radar is working. When ACC is disconnected and the radar switch is ON (1 or 2), the radar working light is always red.
- Radar Sensor Light: Indicates if the radar senses moving objects. If moving objects are detected, the sensor light is red. If no moving objects, the light is off.
6.5.3 Radar Sensor Surface
- Sensor Surface-1 (Front): Senses the front of the car with a non-adjustable 1m sensing distance and a 120° horizontal range.
- Sensor Surface-2 (Inside): Senses the left/right/rear of the car. The radar switch (1 or 2) adjusts the sensing distance, with a 120° horizontal range.
6.5.4 Radar Switch
- 0 (OFF): Radar is closed, no parking monitoring.
- 1 (ON/Weak): Radar is open, weak parking monitor mode. Sensing Range: 0-1 Meters.
- 2 (ON/Strong): Radar is open, strong parking monitor mode. Sensing Range: 0-1.5 Meters.
PS: If the fuse box is wired correctly, the radar working light will be red when the radar switch is ON (1 or 2) after the car is completely turned off.
6.5.5 Working Mode
- When the car engine is fully started: The radar light will not be red. The dash cam powers on automatically and records.
- When the car engine is fully powered off:
- If the radar switch is OFF (0), no parking monitoring occurs.
- If the radar switch is ON (1 or 2), the radar light will be red, indicating working condition.
When the radar detects a moving object, it triggers the dash cam to record for 90 seconds. If objects continue to move, it keeps recording. After 90 seconds with no movement, it enters standby for 10 seconds. If no objects are detected after standby, it remains in standby. If an object is detected, the cycle repeats.
6.5.6 Notes on using radar parking
- Check car battery health.
- For new energy electric cars, know the starting voltage to avoid power loss.
- Some cars may not disconnect power immediately; test after 5-10 minutes.
- Radar sensing distance varies with parking environments, car models, and films.
- Radar monitoring has a switch; turn it off if parking for a long time or not needed.
- In extreme weather or prolonged outdoor parking, turn off the radar switch to suspend parking monitoring.
7. Specifications
| Category | Description |
|---|---|
| Image Sensor | Chip: Allwinner 533, Sensor: 662+GC2053 |
| Random Access Memory | 2GB |
| Rear Cam | Optional (S20—Non-Waterproof) |
| Rear Cam Power Cable | 2.5mm Round hole interface & 5 meters length |
| Channels & Recording Range | 2 CH (Record Front/Rear) or 4 CH (Record Front/Left/Right/Rear) |
| Lens Parameters | Front: F1.6 aperture & 150° wide angle Left/Right/Rear: F1.8 aperture & 150° wide angle |
| Video Format | TS |
| Photo Format | JPG |
| Screen | 4 inch IPS HD Touch Screen |
| Languages | Simplified Chinese / English / Multi-lingual |
| Audio | Built-in microphone and speaker |
| Internal memory | None |
| External Memory | Support 64-256G (Up to U3 Class 10) |
| Power Port | Type-C |
| Supported Car voltage | 12V-24V |
| Work current&voltage | 5V 2.5A |
| Operating Temperature | -20℃~65℃ (-4℉ to 149℉) |
| Button Battery | Built-in RCT button battery (Non-rechargeable) |
8. User Tips
- Enhanced Coverage: The external left and right lenses offer significantly wider viewing angles, improving overall situational awareness.
- Sensitive Parking Monitor: The integrated radar parking monitor is highly sensitive and effective at detecting approaching vehicles, even capturing license plates of nearby parked cars.
- Superior Night Vision: The dash cam provides excellent nighttime clarity and night vision performance, crucial for low-light recording.
- Sleek Design: The integrated sentry radar into the main unit contributes to a much sleeker and less obtrusive design.
- High Image Quality: The front camera, equipped with an IMX662 sensor, delivers excellent image quality.
- Installation Support: If you have concerns about installation, contact the seller for detailed installation videos and guidance.
- Video Segment Length: Videos are saved in 1/2/3 minute segments. This is normal and helps with video preservation and loop recording management.
- Addressing Red Flash on L/R Cam: If the Left/Right Cam flashes red, it might be due to interference from devices with face recognition technology (e.g., mobile phones) or your car's own facial recognition system. Try locking your phone screen or covering your car's face recognition device to verify.
- Memory Card Maintenance: Regularly clean up useless videos and format your memory card every 1-3 months to ensure continuous recording and prolong the card's life.
- Night Vision Color: The Left/Right Cam may show a red color difference or appear purple due to infrared night vision lights and a built-in red filter. This is normal and does not affect video clarity.
9. Troubleshooting (FAQ)
Q1: Can I use a mobile power supply to connect the hardwire kit?
A1: It is not recommended to use an external power supply. The radar relies on the ignition ACC signal, and insufficient voltage can cause instability. Also, continuous recording with multiple lenses consumes significant power, and external power quality cannot be guaranteed, posing risks.
Q2: Is it possible to use my own TYPE-C connector power cord, or the car's USB port?
A2: It is not recommended. The dash cam requires 5V 2.5A. Most car USB ports only provide 2.1A, which may not be sufficient for stable operation. Use the cigarette lighter car charger port or the fuse box connector with the standard 5V 2.5A power cables.
Q3: Is it normal for the dash cam to get hot during operation? Will it be dangerous?
A3: Yes, it is normal for multi-lens dash cams to generate heat due to power consumption. The device uses flame-retardant ABS+PC material and has no rechargeable battery, preventing spontaneous combustion. It is resistant to -20℃ to 65℃. If it exceeds normal operating temperature, it will automatically power off. You can set 'Off-screen recording' in 'System Settings' to reduce screen temperature.
Q4: Why is the date and time incorrect?
A4: This is usually due to incorrect settings. The default time is GMT-5:00. To correct it: 1. Go to Settings, find 'Time Zone' and set it. 2. Turn on GPS function. 3. Turn on WiFi and connect to the APP. The date and time should update automatically.
Q5: Why are videos saved in 1/2/3 minute segments? Can I change it to save as a whole video?
A5: Videos are saved in segments for better preservation and loop recording. When the memory card is full, the oldest segments are automatically deleted. This also helps in viewing specific timeframes. 3 minutes is a reasonable length.
Q6: The Left/Right Cam sometimes has a red flash, why is that? Is this normal?
A6: This is usually due to interference from devices with face recognition technology (e.g., mobile phones) or your car's own facial recognition system. To verify: 1. Lock your mobile phone screen and do not point it at your face, then re-observe the Left/Right Cam. 2. Cover your car's face recognition device and re-watch the Left/Right Cam. You can also check official YouTube videos for related information.
Q7: Why are only a few seconds of video clips saved in the memory card?
A7: This happens when the 'Event' folder (locked videos) occupies too much memory, preventing normal recording or indicating a damaged card. Follow these steps: 1. Go to Playback, check the 'Event' folder for many videos. 2. Save useful videos. 3. Clean up useless videos, or format the entire memory card. 4. After successful formatting, record for 5-10 minutes and check if video duration is normal (3 minutes). 5. If formatting fails, replace the memory card.
Q8: The video recorded from the Left/Right Cam has a color difference and turns purple? Why?
A8: The Left/Right Cam uses four infrared night vision lights and has a built-in red filter for night vision, causing some red color difference. A special night vision filter enhances night vision. This color aberration does not affect video clarity.
Q9: The Front/Rear Cam are normal in color, but the Left/Right Cam are black and white? What should I do?
A9: This is a setup issue. If the IR LED is set to 'ON', the Left/Right Cam will appear black and white regardless of ambient light. Go to Settings, find 'IR LED', and set it to 'Auto'.
Q10: WiFi is connected to the phone, but cannot connect to Viidure APP, what should I do?
A10: Follow these steps: 1. Close the Viidure APP. 2. Go to phone WLAN settings. 3. Find the dash cam's WiFi, click the blue icon, and select 'Forget this network'. 4. Turn off the dash cam, wait 10 seconds, turn it back ON, and turn on WiFi. 5. Rediscover the dash cam's WiFi and link it. 6. Reopen the Viidure APP. If it still doesn't connect, uninstall and reinstall the APP, then repeat the steps.
Q11: Dash cam's WiFi is on, but the phone cannot find/connect to it, what should I do?
A11: This is usually because the phone's WLAN signal isn't retrieving the dash cam's WiFi. Follow these steps: 1. Go to phone Settings, turn off WLAN. 2. Go back to Settings, turn on Airplane Mode. 3. Turn the dash cam OFF and back ON, then turn its WiFi ON. 4. Re-enter WLAN settings; the phone should automatically search for the dash cam's WiFi.
Q12: WiFi is not opening/opening abnormally in dash cam, what should I do?
A12: This indicates a stuck program. Follow these steps: 1. Go to Settings, find 'Reset', click OK, and select YES. 2. Wait for the dash cam to reboot, then try turning on WiFi. If WiFi still doesn't work after a reset, contact support with your order number, 'Version Info' (from Settings, page 16), and the unique SN barcode on the bottom of the dash cam for a software upgrade.
Q13: Dash cam keeps rebooting/not working properly after starting the car, what should I do?
A13: Perform a simple troubleshooting test (recording the process is helpful). 1. Remove all power cables (power and rear cam) from the dash cam. 2. Remove the memory card. 3. Re-energize using the cigarette lighter car charger cable. Provide your order number, a rehearsal video, the SN barcode, and 'Version Info' (if the dash cam can turn on) to support for a solution.
Q14: If the recorder is set to Off-screen recording, how do I judge its working status?
A14: Judge by the working light on the right side of the screen. If always blue, it's on but not recording. If blinking blue, it's on and recording.
Q15: Radar switch is ON after car is off, but radar light is off and recorder doesn't work. Is the hardwire kit broken?
A15: Your radar and P7 hardwire kit are likely not broken. The issue is usually with the BAT+ (yellow wire) connection. It might be connected to a power connector that doesn't supply constant power. Solutions: 1. After the car is off for >30 min, re-check if the yellow wire's connector in the fuse box is a normally charged connector. 2. Re-test and replace the yellow wire (after car is off for >30 min). 3. Set low voltage protection to 11.8V.
Q16: Dash cam worked fine, but now after car is off and radar switch is ON, radar light is off and dash cam doesn't work.
A16: This is likely due to low voltage protection. 1. Power on your car for >30 minutes to fully charge the battery and check if the dash cam works. 2. If it works, power off the car, set radar switch to ON, set low voltage protection to 11.8V, and check if the radar working light turns red.
Q17: Dash cam works when car is on, but after car is off, radar light is off and it keeps recording. Is the hardwire kit broken?
A17: Your radar and P7 hardwire kit are likely not broken. The problem is that the red wire (ACC) is connected to an interface that is still powered after the car is turned off. You need to re-test and connect the red wire to a true ACC interface (one that loses power when the car is off). (Refer to page 25 for wiring principles).
Q18: After car is off, radar working light is red, but recorder keeps recording with no interval.
A18: This is usually due to frequent triggering of the radar by moving objects or interference from items in the same frequency band. Drive your car to an empty parking environment, power it off, lock it, and leave the radar alone for a period to see if it works properly.
10. Warranty and Support
If you have any questions about your product, please feel free to contact us. Inquiries are usually answered within 12-24 hours.
After-Sales Services: tiesfong@gmail.com
Your Opinion Matters
We are committed to improving our products and services. We welcome your constructive feedback and suggestions on how we can do even better.
Download the Viidure App
Scan the QR code below to download the Viidure App for easy control and viewing of your dash cam recordings.

Viidure App QR Code
Official YouTube Channel
Visit our official YouTube channel for helpful videos and tutorials.

TiESFONG YouTube QR Code
11. Video Demonstration
4-Channel Radar Parking Monitoring
Video demonstrating the 4-channel radar parking monitoring mode, showing views from front, rear, left, and right cameras. It illustrates scenarios like a car door opening and a car driving out of a parking space, highlighting the ability to capture license plate numbers.