Product Overview
The MAIWO K10835N is a versatile 3-bay docking station designed for M.2 NVMe, M.2 SATA SSDs, and 2.5/3.5-inch SATA HDDs/SSDs. It supports high-speed data transfer via USB 3.2 Gen2 (10Gbps) and features a convenient bidirectional offline cloning function, allowing you to duplicate drives without connecting to a computer.
Package Contents
- 1x 4-in-1 Hard Drive Cloner (MAIWO K10835N)
- 1x 12V 3A Power Adapter
- 1x USB-C to USB-C+A Data Cable (10Gbps, 31.5 inches)
- 3x Silicone Screws for M.2 SSD
Setup and Data Transfer (Read/Write)
Drive Installation
- For 2.5 or 3.5-inch SATA Hard Drives: Push the 2.5 or 3.5-inch hard drive parallel into the SATA interface of the product.
- For M.2 NVMe & M.2 SATA SSDs: Insert the M.2 SSD into the corresponding M.2 interface vertically.
Connecting to a Computer
- Plug in the 12V power adapter to the DC 12V port on the docking station.
- Connect the docking station to your PC using the provided USB-C to USB-C+A data cable.
- Press the power switch. The blue power light will illuminate, followed by the white hard drive indicator light(s) for inserted drives.
Note: If both a 2.5/3.5-inch SATA drive and an M.2 SATA SSD are inserted simultaneously, the device will only recognize the 2.5/3.5-inch SATA drive. To read the M.2 SATA SSD, please remove the 2.5/3.5-inch SATA drive.
Simultaneous Drive Access
The docking station supports simultaneous access to two drives when connected to a computer:
- M.2 NVMe SSD & M.2 SATA SSD
- M.2 NVMe SSD & 2.5" SATA SSD/HDD
- M.2 NVMe SSD & 3.5" SATA HDD
Offline Clone Function
The MAIWO K10835N supports bidirectional offline cloning, allowing you to duplicate drives without a computer connection.
Cloning Steps
- Choose Clone Mode: Use the clone direction switch to select the desired cloning mode:
- NVMe ⇆ SATA: Set the switch to the left for cloning from M.2 NVMe SSD to 2.5/3.5-inch SATA SSD/HDD (or M.2 SATA SSD).
- SATA ⇆ NVMe: Set the switch to the right for cloning from 2.5/3.5-inch SATA SSD/HDD (or M.2 SATA SSD) to M.2 NVMe SSD.
- Insert Drives: Insert the source hard drive into the designated Source slot and the target hard drive into the Target slot.
- Connect Power: Connect the power adapter to the docking station. DO NOT connect the docking station to a PC when performing an offline clone.
- Press Power Button: Press the power button. The blue power light will turn on.
- Initiate Clone: Long press the CLONE button for 3 seconds. All four progress indicator lights will flash. Release the button, then immediately press the CLONE button once again.
- Cloning Progress: The 25% progress indicator light will begin to flash, indicating that cloning has started. All four progress lights will remain on when cloning is completed.
- Remove Drives: Turn off the power and then remove the hard drives.
Important Note: The actual capacity of the target hard drive must be equal to or larger than the source hard drive, otherwise cloning will not be possible.
Cloning Limitations
- Direct cloning between two M.2 NVMe SSDs is not supported.
- Direct cloning between two M.2 SATA SSDs is not supported.
- Cloning from M.2 SATA to 2.5/3.5-inch SATA is not supported.
New Hard Disk Initialization and Partitioning
For new hard drives, you must initialize, partition, and format them before use. Please back up any important data on existing drives before proceeding.
- Access Disk Management: Right-click on 'Computer' (or 'This PC' on Windows 10/11) and select 'Manage'. In the 'Computer Management' window, click on 'Disk Management' under 'Storage'.
- Initialize Disk: A dialog box will appear prompting you to initialize the new disk. Choose the appropriate partition style:
- MBR (Master Boot Record): Choose MBR if the drive capacity is smaller than 2TB. This is compatible with older operating systems like Windows XP.
- GPT (GUID Partition Table): Choose GPT if the drive capacity is larger than 2TB. This is recommended for modern systems.
- Create New Simple Volume: Right-click on the 'Unallocated' space of your new disk and select 'New Simple Volume'.
- Follow Wizard: Follow the on-screen instructions in the 'New Simple Volume Wizard' to specify the volume size, assign a drive letter, and format the volume. Choose NTFS as the file system.
- Completion: Once the wizard is complete, your new drive will be initialized, partitioned, and formatted, ready for use. You can find it in 'Computer' (or 'This PC').
Specifications
| Attribute | Detail |
|---|---|
| Product Name | MAIWO 2.5/3.5-inch SATA&M.2 NVMe&M.2 SATA Hard Drive Duplicator |
| Model | K10835N |
| Supported Hard Drives | M.2 NVMe & M.2 SATA 2230/2242/2260/2280/22110 SSD, 2.5/3.5-inch SATA SSD/HDD |
| External Interface | USB Type-C (USB 3.2 Gen2x1) |
| Material | ABS plastic |
| Features | Offline Cloning (M.2 NVMe ⇆ M.2 SATA, M.2 NVMe ⇆ 2.5/3.5-inch SATA); Data Transmission |
| Operating Systems | Windows, macOS, Linux, Android (OTG) |
| Transmission Speed | 10Gbps (M.2 NVMe), 6Gbps (M.2 SATA & 2.5/3.5-inch SATA) |
| Supporting Hard Drive Capacity | 30TB (3.5 Inch), 8TB (M.2) |
| Compatible SSD Size | 2230/2242/2260/2280mm |
| Plug Type Options | EU Plug, US Plug, AU Plug, UK Plug |
| Package Dimensions (L x W x H) | 15cm x 11cm x 6cm |
| Package Weight | 0.35 kg |
Maintenance
- Keep the docking station clean and free from dust. Use a soft, dry cloth for cleaning.
- Avoid exposing the device to extreme temperatures, humidity, or direct sunlight.
- Ensure proper ventilation around the device during operation.
- Handle hard drives carefully when inserting or removing them to prevent damage to the connectors.
Troubleshooting
- Drive Not Recognized (Read/Write Mode):
- If both a 2.5/3.5-inch SATA drive and an M.2 SATA SSD are inserted, only the 2.5/3.5-inch SATA drive will be recognized. Remove the 2.5/3.5-inch SATA drive to access the M.2 SATA SSD.
- For new drives, ensure they are initialized, partitioned, and formatted via 'Disk Management' on your computer.
- Check all cable connections (power and data) to ensure they are secure.
- Ensure the power button is pressed and the blue power indicator is lit.
- Cloning Fails or Progress Lights Behave Abnormally:
- 4 blue progress lights not blinking simultaneously after pressing clone button for 3 seconds: This indicates an abnormal situation. Ensure drives are properly seated and the power adapter is connected.
- 4 blue progress lights blinking alternately in groups of two: This means the target hard drive is smaller than the capacity of the source hard drive. Offline cloning requires the target drive to be equal to or larger than the source drive.
- NVMe or SATA hard drive light keeps blinking during cloning: This indicates the corresponding hard drive is abnormal. Check the drive's health.
- Ensure the docking station is NOT connected to a PC during offline cloning.
- Slow Data Transfer Speed:
- Ensure your computer's USB port supports USB 3.2 Gen2 (10Gbps) for optimal speeds.
- Verify the data cable is the original 10Gbps USB-C to USB-C+A cable.
- Actual speeds may vary depending on the drive type (NVMe is faster than SATA) and system configuration.
User Tips
- Verify Cloning Compatibility: Remember that direct M.2 NVMe to M.2 NVMe or M.2 SATA to M.2 SATA cloning is not supported. The cloning function is primarily for M.2 NVMe ⇆ M.2 SATA and M.2 NVMe ⇆ 2.5/3.5" SATA.
- Check Drive Capacity for Cloning: Always ensure your target drive has equal or greater capacity than your source drive for successful cloning.
- Utilize Versatility: This docking station is highly versatile, supporting various drive types (NVMe, M.2 SATA, 2.5/3.5" SATA HDD/SSD) for reading, writing, and cloning.
- Speed Expectations: While the device supports up to 10Gbps, actual transfer speeds depend on the type of drive (NVMe generally faster than SATA) and your computer's USB port capabilities.
Frequently Asked Questions (FAQ)
- Q: Can I use this device to expand my computer's RAM?
- A: No, this device is a hard drive docking station and duplicator, designed for storage drives (SSDs and HDDs), not for expanding Random Access Memory (RAM).
- Q: Can I clone directly from one M.2 NVMe SSD to another M.2 NVMe SSD?
- A: No, the offline cloning function supports M.2 NVMe ⇆ M.2 SATA and M.2 NVMe ⇆ 2.5/3.5-inch SATA drives. Direct cloning between two identical M.2 NVMe drives is not supported by the offline function.
- Q: What happens if the target drive is smaller than the source drive during cloning?
- A: The cloning process will not be possible if the target drive's capacity is smaller than the source drive's capacity. Ensure the target drive is equal to or larger than the source drive.
- Q: Why is my M.2 SATA SSD not recognized when a 2.5/3.5-inch SATA drive is also inserted?
- A: When both a 2.5/3.5-inch SATA drive and an M.2 SATA SSD are inserted, the device prioritizes the 2.5/3.5-inch SATA drive. To read the M.2 SATA SSD, you must remove the 2.5/3.5-inch SATA drive.
Operation Video
Watch the official operation video for a visual guide on setting up and using your MAIWO K10835N docking station.
Warranty and Support
The MAIWO K10835N 3 Bay Docking Station comes with the following service terms:
- Warranty: All products from our store have a 1-year warranty.
- Returns: Enjoy 7 days to return if any quality problems arise.
- Customer Support: All emails will be answered within 24 hours.
For further assistance or more information, please contact us:
- Email: info@maiwoasia.com
- Website: www.maiwoasia.com