1. Product Overview
This manual provides instructions for the JST SM Series Male and Female Housing Connectors. These connectors are designed for various electronic applications requiring secure and reliable wire connections.
Video: Overview of JST SM connector components, showing male and female housings and crimp terminals for various pin counts.

Image: Visual guide to 2-pin, 3-pin, 4-pin, 5-pin, and 6-pin male and female housings with corresponding crimp terminals.
2. Safety & Warnings
Important Safety Information:
- Read all instructions thoroughly before use. Failure to follow these instructions may result in damage to the product or personal injury.
- Warning: Keep the device and its cord out of reach of children under 3 years old.
- Do not expose the connectors to water or excessive moisture.
3. Setup Instructions
Before First Use:
Inspect the product to ensure it is in good condition and free from any visible damage.
Usage Steps:
- Model Selection: Choose the connector with the correct pin count (2-pin, 3-pin, 4-pin, 5-pin, or 6-pin) and gender (male/female) based on your specific circuit requirements.
- Wire Preparation:
- Carefully strip the insulation from the end of the wire to expose the conductor.
- Ensure that the exposed wire conductor has no burrs, frayed strands, or signs of oxidation.
- The applicable wire gauge is AWG #28 to #22 (0.08 to 0.33mm²), with an insulation outer diameter (O.D.) of 1.2mm to 1.8mm.
- Terminal Crimping:
- Use a dedicated crimping tool designed for these types of terminals.
- Place the terminal and the prepared wire into the crimping tool.
- Crimp the terminal onto the wire, ensuring the conductor is fully enclosed within the crimping zone of the terminal. There should be no looseness or exposed wire strands after crimping.
- Insert into Housing:
- Insert the wire with the crimped terminal into the corresponding slot in the connector housing. Push until you feel a click or resistance, indicating it is seated.
- Pull Test: Gently pull on the wire to confirm that the terminal is securely locked in the housing and will not pull out.
- Repeat this process for all wires, following the required pin count for your connector.
- Positioning and Fixing (for PCB Mounting):
- Use fine-tip tweezers to carefully align the connector pins with the corresponding pads or holes on the Printed Circuit Board (PCB). Ensure the pins fully enter the pad holes or make proper contact with the pad areas.
- Gently press down on the connector body to ensure it sits flush against the PCB surface without any warping or gaps.
4. Operating Instructions
Hand Soldering:
- Tools: Use a fine-tip soldering iron (20W-30W) and solder wire with a diameter of 0.5mm-0.8mm.
- Process: First, solder the two pins at the ends of the connector to fix it in place on the PCB. Then, proceed to solder the middle pins sequentially to prevent shifting.
- Post-Soldering: After soldering, clean any flux residue from the soldered joints to prevent corrosion.
SMT (Surface Mount Technology):
- Solder Paste Application: Use a stencil to print solder paste onto the designated pads on the PCB.
- Component Placement: Precisely place the connector onto the applied solder paste.
- Reflow Soldering Profile: Follow these general guidelines for reflow soldering:
- Preheat: 150°C
- Ramp Up: 220°C
- Peak Temperature: 245°C
- Cool Down: Below 100°C
- Post-Soldering Inspection: It is recommended to use a magnifying glass to confirm that the solder joints are full, shiny, and free from cold solder or bridging.
Connector Mating:
- Housing Mating: Align the male housing with the corresponding slot on the female housing. Push evenly until the connectors are fully seated and secure.
- PCB Pin Header Mating: If connecting to a pin header on a PCB, align the connector housing with the pin header and press down vertically. Ensure all pins are fully inserted into the housing slots without any misalignment.
5. Maintenance
To ensure the longevity and reliable performance of your JST SM connectors, keep them clean and dry. Avoid exposing them to harsh chemicals or extreme temperatures. Periodically inspect connections for any signs of wear, corrosion, or damage, especially in high-vibration environments.
6. Troubleshooting
Common Issues and Solutions:
- Difficult Mating/Unmating:
- Check if the male and female housings are properly aligned.
- Inspect for any deformed terminals within the housings.
- Gently adjust the position of any misaligned terminals using fine-tip tweezers if necessary.
- Poor Contact:
- Re-crimp the terminal onto the wire, ensuring a secure connection.
- If re-crimping does not resolve the issue, replace the terminal with a new one.
- Clean any oxidized layer from the surface of the pins and sockets using a suitable contact cleaner.
- Broken Housing:
- Avoid using excessive force when plugging or unplugging the connectors.
- If a housing is broken, it should be replaced to ensure a secure and safe connection.
7. Specifications

Image: Detailed dimensional drawing for 2-pin to 6-pin connectors, showing length, width, and height in millimeters.
| Feature | Specification |
|---|---|
| Product Name | JST Series Male Female Housing Connector |
| Model Number | SM Male Female Housing Connector |
| Brand | ALLiSHOP |
| Material | Plastic Housing, Phosphor Bronze Pin |
| Pitch | 2.54mm |
| Pin Configurations | 2-Pin, 3-Pin, 4-Pin, 5-Pin, 6-Pin |
| Gender | Male, Female |
| Connection Type | Crimping |
| Style | Straight |
| Applicable Wire | AWG #28 to #22 (0.08 to 0.33mm²) |
| Insulation O.D. | 1.2mm ~ 1.8mm |
| Color | Black |
| EU LVD Voltage | Below 50Vac or 75Vdc |
| High-Concerned Chemical | None |
8. User Tips
- These connectors are well-suited for small gauge wires, making them ideal for intricate electronic projects.
- The universal connection measurements are compatible with many electric motor controllers, offering broad application possibilities.
- Always double-check the crimp connection by gently pulling the wire to ensure it is secure before inserting into the housing.
9. Warranty & Support
Manufacturer Information:
Shenzhen Luozhuo Technology Co., Ltd
CN-Floor 5, No.32 Zhongxing Road, Liguang Village, shiyan Baoan District, Shenzhen, Guangdong
Email: Roson@locheuk.com
EU Authorized Representative:
APEX CE SPECIALISTS LIMITED
UNIT 3D NORTH HOUSE, NORTH POINT BUSINESS PARK, NEW MALLOW ROAD
Email: info@apex-ce.com
Compliance:
This product holds a CE Certificate of Compliance.
Warranty:
For warranty information and support, please contact the manufacturer or your point of purchase directly.