Merlin E960M

Contents

Merlin E960M Security+2.0 Garage Door Opener Remote Control User Manual

Model: E960M

Introduction

This manual provides instructions for the setup, operation, and maintenance of your Merlin E960M Security+2.0 Garage Door Opener Remote Control. Please read these instructions carefully before use to ensure proper functionality and safety.

Merlin E960M remote control with keychain

Figure 1: Merlin E960M Remote Control with Keychain

Setup and Programming

The Merlin E960M remote control uses rolling code technology and operates at a frequency of 433.92MHz. It is compatible with Merlin+ and Merlin 842 systems, including models E940M, E945M, E950M, and E960M.

Merlin E960M remote control and compatible models with frequencies

Figure 2: Merlin E960M Remote Control and Compatible Models

1. Switching Remote Programs (Merlin vs. Merlin+ 2.0)

Your remote control may support different programming modes. Follow these steps to switch between programs:

  1. Press and hold buttons 1 and 3 simultaneously on the remote control.
  2. Release the buttons when the LED light on the remote lights up and blinks.
  3. Press and hold the desired program button. If the red light is on, the remote is in Merlin+ 2.0 program mode.
  4. To switch back to the original program, repeat the same operation.

Video 1: Demonstrating how to switch programs on the remote control.

2. Adding the Remote to Your Opener (Programming on Receiver)

To program the E960M remote control to your garage door or gate opener, you will typically need to access the opener's receiver unit. The process involves setting DIP switches on the receiver and then pairing the remote.

  1. Identify your opener type: Refer to the DIP switch diagram for 'Merlin+' or 'Merlin 842' to correctly configure the switches on your receiver.
  2. Set DIP Switches: Adjust the DIP switches on your opener's receiver to match the configuration shown in the diagram for your specific Merlin system.
  3. Activate Learning Mode: On your opener's panel, press and release the orange 'Learn' button (usually labeled 'Learn' or 'Code'). The opener's light will flash once, indicating it is in learning mode.
  4. Pair Remote: While the opener is in learning mode, press and hold the desired button on your E960M remote control. The opener's light should flash or click twice (if no light bulb is installed) to confirm successful pairing.
  5. Test: Press the programmed button on your remote to ensure it operates the door or gate correctly.

Video 2: Demonstrating DIP switch setting and pairing the remote with a receiver.

Operating Instructions

Once programmed, operating your Merlin E960M remote control is straightforward:

  1. Open/Close: Press the programmed button on the remote control to open or close your garage door or gate.
  2. Stop: Press the button again while the door/gate is in motion to stop it.
Hand pressing a button on the remote control

Figure 3: Operating the remote control.

Maintenance

To ensure the longevity and reliable performance of your remote control, follow these maintenance guidelines:

  • Battery Replacement: The remote control includes a battery. When the remote's range decreases or the LED light becomes dim, it's time to replace the battery. Typically, these remotes use a CR2032 coin cell battery. To replace, carefully open the remote casing (often by prying gently along the seam) and swap the old battery with a new one, ensuring correct polarity.
  • Cleaning: Clean the remote control periodically with a soft, dry cloth. Avoid using harsh chemicals or abrasive cleaners.
  • Storage: Store the remote in a dry place, away from extreme temperatures and direct sunlight.
Front and back view of the Merlin E960M remote control

Figure 4: Front and back view of the remote control.

Troubleshooting

If your remote control is not functioning as expected, consider the following:

  • Remote Not Responding:
    - Check the battery. A weak or dead battery is a common cause.
    - Ensure the remote is within the operating range (10-150m in open space).
    - Verify that the remote has been correctly programmed to your opener's receiver. Repeat the programming steps if necessary.
  • Reduced Range:
    - Replace the battery.
    - Ensure there are no obstructions between the remote and the opener's receiver.
    - Check for sources of radio interference in the area.
  • Opener Not Entering Learning Mode:
    - Consult your opener's specific manual for instructions on how to activate learning mode.

Specifications

FeatureSpecification
Model NumberE960M (Compatible with MERLIN+2.0, E945M, E950M, E940M)
Encoding MethodRolling code
Frequency433.92MHz
Operating Distance10-150m (open space)
CertificationCE
UsageProgram on receiver (garage door/gate door/sliding gate/barrier etc)
Included ItemsRemote Control, Key Chain, English Manual, Battery
OriginMainland China
Package Length12 cm
Package Width12 cm
Package Height2 cm
Package Weight0.05 kg

User Tips

  • Check Compatibility: Before purchasing or programming, always confirm that the E960M remote is compatible with your specific garage door or gate opener model. While it supports Merlin+ 2.0, E940M, E945M, and E950M, verifying your opener's model is crucial.
  • Reliable Performance: Users have noted the remote controls work effectively and are reliable once programmed.

Warranty and Support

For further assistance or detailed information, please refer to the official user manual PDF available from the seller. You can view the PDF here.

Manufacturer: Shenzhen Scimagic Development Technology Co.Ltd
Address: Honghai Gebu Building 2301, Baoan Road, Songgang Baoan District, Shenzhen, Guangdong, China.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.