1. Product Information
This manual provides instructions for the installation and use of the RACBOX Side Rearview Mirror Turn Signal Light Housing, an auxiliary accessory designed for automotive lighting. This product is intended for the normal replacement and upgrade of original car lights.

Image: RACBOX Side Rearview Mirror Turn Signal Light Housing, showing its appearance on a vehicle mirror.
Product Contents
The package typically includes two (2) pieces of the side mirror turn signal light housing. Please note that bulbs are NOT included and must be purchased separately.

Image: Two pieces of the turn signal light housing, supplied without bulbs.
2. Safety & Warnings
Important Safety Information
Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.
- Keep the device and its cord out of reach of children under 3 years old.
- Keep away from children unless supervised by an adult.
- Do not use this product for purposes other than its intended use.
- Inspect the product before each use; do not use if damaged.
- Follow installation and operation guidelines to avoid injury.
- Do not expose to water or moisture during storage or handling before installation.
3. Product Overview
The Side Rearview Mirror Turn Signal Light Housing is designed as a direct replacement for the original mirror indicator lights on compatible Toyota models. It features a clear shell and is made from durable ABS plastic.

Image: Close-up of the clear, textured lens.
Dimensions

Image: Dimensions of the turn signal light housing.
Rear View and Part Identification

Image: Rear view of the light housing, showing mounting clips and internal markings.
4. Installation Instructions (Setup)
Professional installation is recommended. Ensure the vehicle is turned off and cooled down before beginning installation. Always wear appropriate safety gear.
- Prepare the Vehicle: Turn off the vehicle engine and disconnect the power (e.g., remove the negative battery terminal) to prevent short circuits during installation.
- Access Original Light: Carefully remove the cover or lens of the original mirror light. This may involve prying with a plastic trim tool to avoid scratching the paint.
- Remove Old Component: Take out the old bulb or light assembly from the mirror housing.
- Disconnect Wiring: Disconnect the power plug of the original mirror light.
- Install New Light: Install the new mirror light housing into the mirror housing correctly. Ensure it snaps securely into place.
- Connect Wiring: Connect the power plug to the new light housing. If the light does not work after connection, reverse the plug polarity and try again.
- Secure and Reassemble: Fix the light firmly and reinstall the mirror cover or lens. Ensure all components are properly seated and secured.
- Test Functionality: Reconnect the vehicle's power. Test the turn signal function and light brightness to ensure normal operation.
- Final Check: Check all connections to make sure they are stable and reliable before driving.

Image: Before and After installation comparison.
5. Operation
Once installed, the side rearview mirror turn signal light housing functions as a direct replacement for your vehicle's original turn signal indicator. When the turn signal is activated, the light will blink, providing visual indication to other drivers.
6. Maintenance
- Cleaning: Clean the light housing periodically with a soft cloth and mild automotive cleaner to maintain clarity and visibility. Avoid abrasive cleaners or harsh chemicals.
- Inspection: Regularly inspect the light housing for any cracks, damage, or loose connections. Replace if any damage is found to ensure proper functionality and safety.
- Bulb Replacement: As this product is a housing only, ensure that any installed bulbs are of the correct type and wattage as specified by your vehicle manufacturer. Replace bulbs as needed following your vehicle's service manual.
7. Troubleshooting
Light Not Functioning After Installation
- Check Wiring Polarity: If the light does not illuminate, disconnect the power plug and reverse its connection. Some LED bulbs or circuits are sensitive to polarity.
- Verify Connections: Ensure all electrical connections are secure and fully seated. A loose connection can prevent the light from working.
- Inspect Bulb: If using a separate bulb, ensure it is correctly installed and not faulty. Test the bulb in another known working socket if possible.
- Check Vehicle Fuse: Consult your vehicle's manual to check the fuse associated with the turn signal lights. A blown fuse will prevent the lights from working.
- Professional Assistance: If the issue persists after checking the above, it is recommended to seek assistance from a qualified automotive technician.
8. Specifications
| Attribute | Detail |
|---|---|
| Item Type | Side Mirror Signal Blinker / Side Wing Rearview Mirror Turn Signal Light Housing |
| Model Name | 81741-02040 |
| Material | ABS Plastic |
| Shell Color | Clear |
| Bulbs Included | NO |
| Origin | Mainland China |
| Fitment | For Toyota Auris (2012-2018), C-HR (2016-2020), Avensis (2015-2018), COROLLA Verso (2013-2018) |
| Product Dimensions (approx.) | Length: 129mm, Height: 34mm |
| Package Dimensions (approx.) | Length: 24cm, Width: 15cm, Height: 10cm |
| Package Weight (approx.) | 0.07 kg |
9. User Tips
- Verify Fitment: Before purchasing and installing, always double-check the compatibility with your specific vehicle model and year. While listed for various Toyota models, slight variations can occur. For example, users have confirmed fitment for Toyota Auris Touring Sports and Toyota Verso 2013.
- Bulb Compatibility: Remember that this product is a housing only. Ensure you have compatible turn signal bulbs (not included) for your vehicle's electrical system.
- Professional Installation: If you are not confident with automotive electrical work or trim removal, consider having the installation performed by a professional to avoid damage to your vehicle or the product.
10. Warranty & Support
This product has undergone strict quality testing and meets relevant national automotive lighting industry standards. For any support inquiries or warranty information, please refer to the manufacturer's official documentation or contact the seller directly.
Manufacturer: Guangzhou Bai Ji Tun Trading Co., Ltd
EU Authorized Representative: APEX CE SPECIALISTS LIMITED
A PDF user manual is available for download from the product page for detailed information.