1. Important Safety Information
Warning: To avoid personal injury, property damage, or accidental damage to the product, read all of the information in this section before using the product.
1.1. Work Area Safety
- Keep work area clean and well lit. Cluttered benches and dark areas may cause accidents.
- Do not connect or disconnect the tool while the ignition is on or the engine is running.
- DO NOT attempt to operate the tool while driving the vehicle. Have a second person to operate the tool.
- Before testing a vehicle, put the transmission in PARK (for automatic transmission) or NEUTRAL (for manual transmission). Engage the parking brake and chock the tires.
- NEVER smoke or allow a spark or flame in vicinity of battery or engine.
- The vehicle shall be tested in a well-ventilated work area, as engines produce various poisonous compounds (hydrocarbon, carbon monoxide, nitrogen oxides, etc.).
- Do not operate the tool in explosive atmospheres, such as in the presence of flammable liquids, gases, or heavy dust.
- Never leave the vehicle unattended while testing.
- Keep a fire extinguisher suitable for gasoline/chemical/electrical fires nearby.
- Use extreme caution when working around the ignition coil, distributor cap, ignition wires and spark plugs. These components create hazardous voltages when the engine is running.
- Keep bystanders, children and visitors away while operating the tool.
- This product is not a toy. Do not allow children to play with or near this tool.
- Use as intended only. Do not modify.
- Inspect before every use; do not use if parts are loose or damaged.
- Do not place the tool on any unstable surface.
- Handle the tool with care. If the tool is dropped, check for breakage and any other conditions that may affect its operation.
- Keep the tool dry, clean, free from oil, water or grease. Use a mild detergent on a clean cloth to clean the outside of the tool when necessary.
- Store the tool and accessories in a locked area out of the reach of children.
- To avoid damaging the tool or generating false data, please make sure the vehicle battery is fully charged and the connection to the vehicle DLC (Data Link Connector) is clear and secure.
- If the VCI (Vehicle Communication Interface) is not in use for a long period of time, it is suggested to unplug the VCI from vehicle's DLC to conserve battery power.
1.2. Electrical Safety
- Do not use the tool while standing in water.
- Avoid body contact with grounded surfaces such as pipes, radiators, ranges and refrigerators.
- Do not expose the tool or power adaptor to rain or wet conditions. Water entering the tool or power adaptor increases the risk of electric shock.
1.3. Personal Safety
- Wear an ANSI-approved eye shield when testing or repairing vehicles.
- Do not wear loose clothing or jewelry. Keep hair, clothing, hands, tools, and test equipment away from moving or hot engine parts. Loose clothes, jewelry, or long hair can be caught in moving parts.
- Do not use the tool while tired or under the influence of drugs, alcohol, or medications. A moment of interruption can result in serious personal injury.
- People with pacemakers should consult their physician(s) before use. Electromagnetic fields in close proximity to heart pacemaker could cause pacemaker interference or pacemaker failure.
- The warnings, precautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator.
- There are no user serviceable parts. Have the tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the equipment is maintained.
- Please use the included battery and charger. Risk of explosion if the battery is replaced with an incorrect type.
- Automotive batteries contain sulfuric acid that is harmful to skin. In operation, direct contact with the automotive batteries should be avoided. Keep the ignition sources away from the battery at all times.
1.4. Precautions on Operating Vehicle's ECU
- Do not disconnect battery or any wiring cables in the vehicle when the ignition switch is on, as this could avoid damage to the sensors or the ECU.
- Do not place any magnetic objects near the ECU. Disconnect the power supply to the ECU before performing any welding operations on the vehicle.
- Use extreme caution when performing any operations near the ECU or sensors. Ground yourself when you disassemble PROM, otherwise ECU and sensors can be damaged by static electricity.
- When reconnecting the ECU harness connector, be sure it is attached firmly, otherwise electronic elements, such as ICs inside the ECU, can be damaged.
2. Product Overview
The LAUNCH X431 PRO3S+ Elite SmartlinkC 2.0 is an advanced diagnostic tool inheriting LAUNCH's cutting-edge diagnostic technology. It offers extensive vehicle coverage, powerful functions, and precise test results. Key features include Intelligent Diagnose, Local Diagnose, EV (Electric Vehicle) Diagnose & Service, SmartLink Super Remote Diagnose, X431 Remote Diagnose, Service Functions, Toolbox, Software Update, Feedback, Online Mall, and Diagnostic History.

Figure 2.1: LAUNCH X431 PRO3S+ Elite SmartlinkC 2.0 Overview
2.1. Package List
The accessories may vary based on destination. Please consult your seller or check the package list provided with your tool.

Figure 2.2: LAUNCH X431 PRO3S+ Elite Package Contents
- Display Tablet x 1: Indicates the test result.
- SmartLink C V2.0 Device x 1: Collects vehicle data and sends it to the tablet for analysis.
- Diagnostic Cable x 1: Connects the SmartLink C device to the OBD II vehicle's DLC.
- Data Cable (Type A-Type C) x 1: Connects the tablet to a PC for data exchange/charging.
- Data Cable (Type A-Type B) x 1: Connects the SmartLink C device to PC for J2534 reprogramming or connects the SmartLink C device to the diagnostic tablet to perform vehicle diagnosis.
- Crossover Cable x 1: Connects the SmartLink C device to the modem.
- Password Envelope x 1: Contains the product Serial Number and Activation Code for registration.
- Quick Start Guide x 1
- Power Adaptor x 1 + Switching Adaptor x 2: Charges the tablet via the AC outlet.
- Non-16pin Adaptor Kit for Passenger Cars (optional): For different vehicle diagnostic sockets, various non-16pin connectors may be necessary.
2.2. Components & Controls
The diagnostic system consists of two main components: the Display Tablet and the SmartLink C V2.0 Device.
2.2.1. Display Tablet
The tablet acts as the central processing system, receiving and analyzing live vehicle data from the SmartLink C device and displaying test results.
| Item | Description |
|---|---|
| 1. Microphone | For audio input. |
| 2. Type-A USB Port | Connects to SmartLink C for diagnosis via USB, or to compatible add-on modules (e.g., Videoscope) or USB storage devices. |
| 3. Type-C USB Port | Connects to AC outlet for charging or to PC for data exchange. |
| 4. POWER Key | Turns the tablet on/off. Press and hold for 8 seconds for forced shutdown. |
| 5. LCD Screen | Displays test results and user interface. |
| 6. Speakers | For audio output. |
| 7. Rear Camera | For capturing images. |
| 8. Adjustable Stand | For convenient viewing angles. |
2.2.2. SmartLink C V2.0 Device
The SmartLink C V2.0 device offers powerful functions and can be used in three main situations:
- As a VCI (Vehicle Communication Interface): Works with the tablet's Diagnose module to obtain vehicle data and send it to the tablet wirelessly or via data cable for analysis.
- As a SmartLink C (Customer) Dongle: Does not communicate with the tablet directly but works with the tablet's SmartLink module. The tablet issues remote diagnostic requests, and the SmartLink C dongle receives and executes commands from the remote SmartLink B (Business).
- As a Local J2534 PassThru Device: Can be used with a PC running OEM diagnostic software for J2534 reprogramming.
| Item | Description |
|---|---|
| 1. DB-15 Diagnostic Connector | Connects to the vehicle's DLC (Data Link Connector) port via the diagnostic cable. |
| 2. Touch Screen | Displays device status. |
| 3. LAN/WAN Port | Connects to the modem via crossover cable for SmartLink Super Remote Diagnostics. |
| 4. DC-IN Power Jack | Obtains power via diagnostic cable from vehicle's DLC or external DC power supply. |
| 5. Data I/O Port | Connects to the tablet for vehicle diagnosis or to a PC for J2534 reprogramming. |
3. Technical Specifications
3.1. Display Tablet
- Operating System: Android
- Memory: 4GB
- Storage: 64GB
- Screen: 10.1 inch capacitive touch screen with a resolution of 1280 x 800 pixels
- Camera: Rear-facing 8.0MP camera
- Connectivity: Wi-Fi (802.11a/b/g/n/ac), Bluetooth
- Working Temperature: 0°C ~ 50°C
- Storage Temperature: -20°C ~ 70°C
3.2. SmartLink C V2.0 Device
- Size: 200mm × 110mm × 47mm
- Working Voltage: DC 9~36V
- Power Consumption: ≤ 6W
- Communication: Wireless and wired
- Working Temperature: 0°C ~ 50°C
3.3. General Product Properties
| Property Name | Value |
|---|---|
| High-concerned chemical | None |
| Use | Not Telecommunication |
| Electronic | No |
| Wireless Support | Bluetooth |
| Is Batteries Included | Yes |
| Item Weight | 0.2kg |
| External Testing Certification | CE |
| Special Features | Bluetooth |
| Software Version | Latest |
| Hardware Version | Newest |
| Brand Name | LAUNCH |
| Origin | Mainland China |
| Material | Plastics |
| Item Type | Car Diagnostic Cables and Connectors |
| Power (W) | w |
| Warranty | 5 years |
4. Setup
4.1. Initial Use
4.1.1. Charging & Turning On
- Plug one end of the included charging port of the tablet, and the other end to the power adaptor.
- Connect the other end to the AC outlet.
If the battery icon appears on the screen, it indicates it is being charged. If the logo changes into a full battery icon, it indicates that the battery is fully charged. Unplug the power adaptor from the tablet.
Note: If the battery remains unused for a long period of time or is completely discharged, it is normal that the tool will not power on while being charged. Please charge it for a period of 5 minutes and then turn it on.
Warning: Please use the included power adaptor to charge your tool. No responsibility can be assumed for any damage or loss caused as a result of using power adaptors other than the one supplied.
Press the [POWER] key for 3 seconds; an option menu will pop up on the screen. Tap Power off to turn the tool off.
4.1.2. Screen Layout
The following on-screen buttons are available at the bottom of the screen:
- BACK: Tap it to return to the previous screen.
- HOME: Tap it to navigate to the Android's home screen.
- Recent Apps: Tap it to view the recently launched applications.
- Screenshot: Tap it to capture the current screen.
4.1.3. Adjust Brightness
Note: Reducing the brightness of the screen is helpful to conserve battery power.
- On the home screen, tap Settings -> Display -> Brightness level.
- Drag the slider to adjust it.
4.1.4. Change System Language
The tool supports multiple system languages. To change the language of the tool, please do the following:
- On the home screen, tap Settings -> System -> Language & input -> Languages.
- Tap Add a language, and then choose the desired language from the list.
- Tap and hold the desired language and drag it to the top of the screen and then release it; the system will change into the target language.
4.1.5. Set Standby Time
If no activities are made within the defined standby period, the screen will be locked automatically and the system enters sleep mode to save power.
- On the home screen, tap Settings -> Display -> Advanced -> Sleep.
- Choose the desired sleep time.
4.1.6. WLAN Setup
The tablet has built-in Wi-Fi for internet connectivity. Once online, you can register the tool, surf the Internet, get apps, send email, launch remote diagnosis, and check for software updates.
Connect to a Wi-Fi network
- On the home screen, tap Settings -> Network & Internet -> WLAN.
- Slide the Wi-Fi switch to ON; the tablet starts searching for available wireless networks.
- Select a wireless network.
- If the chosen network is open, the tablet will connect automatically.
- If the selected network is encrypted, a network password will need to be entered.
- When Connected appears, it indicates the Wi-Fi connection is complete.
Note: When Wi-Fi is not required, it should be disabled to conserve battery power.
Disconnect from a Wi-Fi network
- On the home screen, tap Settings -> Network & Internet -> WLAN.
- Tap the network with a Connected status, then tap Disconnect.
4.2. Register & Update
For initial use, registration is the necessary first procedure to activate the tool.
- Tap the application icon on the home screen to launch it, and then tap Login on the upper right corner of the screen.
- If you are a new user, tap New Registration to enter the sign-up page. Fill in the required information and tap Register.
- Input the 12-digit Product Serial Number and 8-digit Activation Code (found in the password envelope), and then tap Activate.
- After successful registration, tap OK to navigate to the update center to download all available software.
After registration, the wireless communication between the tablet and the SmartLink C device is automatically established.
4.3. Connections
4.3.1. Preparation
- Make sure that the ignition is turned off and vehicle battery voltage range is 9-14V or 18-30V.
- Find the DLC (Data Link Connector) location. For passenger cars, the DLC is usually located 12 inches from the center of the instrument panel, under or around the driver's side. For commercial vehicles, the DLC is always located in the driver's cab.
- Refer to the vehicle connection instructions below.
- Turn the vehicle's ignition ON with the engine OFF.
- The tool is now ready for diagnostics.
4.3.2. Vehicle Connection
The method to connect the VCI device to a vehicle's DLC depends on the vehicle's configuration:
- For OBD II vehicles: Use the included diagnostic cable (DB15F to HD15F data cable and HD15M to OBD16 adaptor) to connect the VCI to the vehicle's DLC port.
- For non-OBDII vehicles: Select the appropriate adaptor according to the vehicle's DLC port type. Loosen the captive screws of the DB15F to HD15F data cable and disconnect the HD15F to OBD16 adaptor. Connect the data cable with the target adaptor (sold separately) and tighten the screws.
If you choose to perform vehicle diagnosis via data cable, connect one end of the data cable into the VCI, and the other end into the data I/O port of the tablet.
4.3.3. Communication Setup
The tablet can communicate with the VCI device wirelessly (Bluetooth) or wired (USB).
- After user registration, wireless communication between the tablet and VCI is automatically established.
- USB connection is a simple and quick way to establish communication. After properly connecting the data cable from the tablet to the VCI, the VCI navigation button at the bottom of the screen will be enabled, indicating a successful USB connection.
Note: The USB connection provides the most stable and fastest communication. When all communication methods are applied, the tablet will use wired communication as the default priority.
5. Operating Instructions
5.1. Diagnosis
The tool offers various diagnostic methods to suit different needs.
5.1.1. Intelligent Diagnose
This function allows you to automatically obtain VIN information and guide you to the vehicle information page without manual menu selection. The page lists historical diagnostic records and provides quick access to local diagnose and diagnostic functions.
Note: Ensure the VCI device is properly connected to the vehicle's DLC and a stable network connection is available.
- Tap Intelligent Diagnose on the Job menu screen to start pairing with the VCI device.
- After pairing, the tablet reads the vehicle VIN.
- If the VIN is found in the remote server database, the vehicle information page appears. You can then:
- Tap Diagnostic to start a new diagnostic session.
- Tap Scan History to view historical repair records.
- Tap Quick access to go directly to the diagnostic function selection screen.
- If the VIN cannot be accessed, you can manually enter the VIN or use the VIN recognition module.
5.1.2. Local Diagnose
This function allows you to diagnose electronic control systems of single vehicle models by manually executing menu-driven commands.
- Tap Local Diagnose to enter the vehicle selection page.
- Choose one of the following ways to access vehicle diagnostic software:
- VINSCAN: Use Camera Scan to automatically scan the VIN or Enter VIN to input it manually.
- Tap a corresponding diagnostic software logo and follow on-screen instructions.
- Select the diagnostic software version (e.g., DEMO V15.51).
- Select the vehicle model (e.g., TOYOTA).
- Select the desired test item to proceed.
Diagnostic Functions
- System Topology: Displays available vehicle systems in a topology structure.
- System List: Displays available vehicle systems in a list.
- ADAS Calibration: Performs ADAS calibration operations.
- Smart Detection: Quickly accesses all electronic control units, generates a detailed report, and highlights malfunctioning systems in red.
- Read Fault Code: Displays detailed information of DTC records.
- Clear Fault Code: Erases codes from the vehicle. Ensure ignition is ON and engine is OFF.
- Read Data Stream: Retrieves and displays live data and parameters from the ECU.
- Read Freeze Frame: Takes a snapshot of operating conditions when a fault occurs.
- Actuation Test: Accesses vehicle-specific subsystem and component tests.
- Special Functions: Offers coding, reset, relearn, and other service functions.
5.1.3. Remote Diagnose
The tool supports two remote diagnostic platforms: SmartLink Super Remote Diagnostics and X431 Remote Diagnostics.
SmartLink Super Remote Diagnostics
This system allows technicians (SmartLink C) to seek assistance from remote master technicians or repair shops (SmartLink B) for complex vehicle problems.
X431 Remote Diagnostics
This option facilitates instant messaging and remote diagnosis between repair shops or technicians.
- Tap Remote Diagnose -> X431 Remote Diagnosis.
- To add friends, tap Contacts, input the partner's username in the search bar, and tap Search.
- Tap the desired name from the list and tap Add friend to send a request.
- Once the partner accepts, they will be listed in the Contacts tab.
- To start instant messaging, tap the desired friend's photo.
- To launch remote diagnosis (Scanner-To-Scanner), tap Remote Diagnostic from the function option selection screen.
- To launch remote diagnosis (Scanner-To-PC), slide the Remote switch to ON, choose the car model, and notify the PC client technician of the website (http://remote.x431.com) and your device's serial number.
5.1.4. EV (Electric Vehicle) Diagnose
This function applies to new energy vehicles and includes Vehicle Diagnosis and Battery Pack Detection.
Note: This function requires the optional New Energy Vehicle Diagnosis Add-on Kit.
Vehicle Diagnosis
This function manually diagnoses electronic control systems of new energy vehicles.
Battery Pack Detection
This function detects the battery pack of new energy vehicles via vehicle model or battery brand.
- Tap Battery Pack Detection.
- Select the vehicle (e.g., BYD -> E5).
- Choose the desired BMS model.
- Select the preferred detection mode (Via OBD diagnostic interface, Via Jumper, or Via Specific test adaptor) and follow the on-screen instructions.
5.2. Service Function (Reset)
The tool offers coding, reset, relearn, and other service functions to restore vehicles to functional status after repair or replacement. Available tests vary by vehicle manufacturer, year, and model. Regular updates are recommended for new service functions.
There are two methods for service functions: Manual Reset or Auto Reset. Auto Reset sends commands to the vehicle's ECU, while Manual Reset guides the user through on-screen instructions.
- Tap "Service Function".
- Choose the desired service function.
- Select the desired car brand.
- Select the reset mode (varies by vehicle).
- Follow the on-screen instructions to proceed.
5.3. Toolbox (Extended Modules)
This function includes various add-on modules, each consisting of hardware and an app. These modules require specific compatible hardware (sold separately) to function.
- TPMS: Configures the tablet as a TPMS activation & diagnostic tool. Requires compatible TSGUN device.
- ADAS (Calibration): Calibrates camera-based & radar-based driver assistance systems. Requires specific ADAS calibration tool.
- Oscilloscope: Helps diagnose faults in automotive electronic equipment and wiring. Requires specific Scopebox.
- Sensor Simulator: Diagnoses and simulates vehicle sensor faults. Requires compatible S2-2 Sensorbox.
- Videoscope: Checks unseen parts of the engine, fuel tank, braking system, etc. Requires compatible Videoscope.
- BST360 (Battery Tester): Performs battery detection, charging, and cranking tests. Requires specific Bluetooth battery tester.
- Multimeter: Measures physical parameters like voltage, resistance, frequency. Utilizes EM101N hardware.
- Current Clamp: Performs AC/DC current and DC voltage tests. Requires compatible current clamp.
- Insulation Tester: Measures insulation resistance, voltage, and other parameters for power equipment.
- Immobilizer Programmer: Performs read-write functions for vehicle keys, EEPROM, MCU, and EEPROM/FLASH of vehicle engine and gearbox ECU. Requires specific immobilizer programmer.
- Key Programmer: Identifies car key chips, generates chip models, reads remote control frequency, and generates remote control devices. Requires compatible key programmer.
5.4. Diagnostic Widget
The diagnostic widget provides quick access to various diagnostic utilities:
- Vehicle Coverage: Check supported vehicle models.
- CAN Bus Pin Detection: Detect voltage of OBD II diagnostic socket pins and supported protocol types.
- CANScope: Monitor vehicle CANBUS data and analyze fault causes.
- Data Stream Sample: Manage recorded data stream sample files.
- DLC Voltage Check: Check vehicle battery voltage.
- Reset MSVIN: Decode VIN information of ECUs and output inconsistent VINs.
- Diagnostic History: Access previously tested vehicle records.
5.5. J2534 Reprogramming
The SmartLink C can be used as a J2534 PassThru device for ECU reprogramming. This requires a PC with OEM diagnostic software and the LAUNCH J2534 tool installed (downloadable from https://en.cnlaunch.com).
Video 5.1: Product Overview and Features
6. Maintenance
6.1. Software Update
This module allows you to update the diagnostic software, app, and frequently used software.
6.1.1. Update Diagnostic Software & APP
- Go to Software Update on the Job Menu and tap the Downloaded tab.
- The Available tab displays a list of software that can be updated, categorized into:
- Common software: Includes common apps associated with the diagnostic app.
- Frequently used vehicle software: Diagnostic software that is frequently used.
- Other vehicle software: Diagnostic software rarely used.
- If no diagnostic software was downloaded during sign-up, all diagnostic software is selected by default. Tap Update to download.
- If some software was downloaded during sign-up, only frequently used software is selected. Tap Update to download.
- To download specific software, check the box next to the vehicle model and tap Update.
- After download, software packages will be installed automatically.
6.1.2. Update Frequently Used Software
If you only intend to update frequently used software, go to Software Update and tap the Downloaded tab.
6.2. Clear Cache
This item is used to clear the App cache.
- Tap Clear Cache. A pop-up window will appear.
- Tap OK to clear cache. The system will restart the App.
6.3. Fix Connector Firmware/System
Use this item to upgrade and fix VCI firmware/system. During fixing, do not cut power or switch to other interfaces.
7. Troubleshooting (FAQ)
7.1. About Diagnostic Tablet
7.1.1. How to save power?
- Turn off the screen while the tool is idle.
- Set a shorter standby time.
- Decrease the brightness of the screen.
- If WLAN connection is not required, turn it off.
7.1.2. Communication error with vehicle ECU?
Please confirm:
- Whether the VCI device is correctly connected.
- Whether ignition switch is ON.
- If all checks are normal, send vehicle year, make, model and VIN number to us using Feedback feature.
7.1.3. Failed to enter into vehicle ECU system?
Please confirm:
- Whether the vehicle is equipped with this system.
- Whether the VCI device is correctly connected.
- Whether ignition switch is ON.
- If all checks are normal, send vehicle year, make, model and VIN number to us using Feedback feature.
7.1.4. How to download the diagnostic app after resetting the tablet?
Note: Before registration, make sure the network is properly connected.
After the tablet has been successfully reset, follow the steps below to download the App:
- Launch the browser and the default official Launch website opens (if a blank page pops up, just type in www.x431.com in the input bar).
- Tap Login, input the username and password and tap Log In.
- Make sure that the serial number is correct, tap APP application program and tap the Download icon to start downloading.
- After the download is complete, follow the on-screen instructions to install it.
- After installation, use the existing username and password to login and go to update center to download the diagnostic software.
7.1.5. What to do if the language of vehicle diagnostic software does not match the system language?
English is the default system language of the tool. After the system language is set to the preference language, go to the update center to download the vehicle diagnostic software of the corresponding language.
If the downloaded diagnostic software is still displayed in English, it indicates that the software of the current language is under development.
7.1.6. How to retrieve the login password?
- Tap the application icon on the home screen to launch it.
- Tap Login on the upper right corner of the screen.
- Tap Retrieve password.
- Input product S/N and follow the on-screen prompts to retrieve the password.
7.2. About SmartLink Diag.
7.2.1. What network conditions are required for SmartLink Diag.?
The remote SmartLink Diag. operation requires a network broadband of 100MB or above.
7.2.2. What does the word "Delay" displayed on the SmartLink C screen mean?
The Delay (network delay) indicates the state of the network communication. Different colors represent different delay status:
- Green: Indicates a shorter network delay, higher success rate of remote communication.
- Yellow: Indicates a medium network delay, medium success rate of remote communication.
- Red: Indicates a longer network delay, lower success rate of remote communication. Remote ECU reprogramming operations are not suggested.
7.2.3. My network delay is so long.
Possible reasons:
- Greater distance between SmartLink B2.0/SmartLink B and SmartLink C V2.0 dongle.
- Too many network communication nodes.
- Poor network and slow data communication speed.
7.2.4. Some systems of some old vehicles cannot be tested.
The SmartLink C V2.0 dongle supports CAN2.0/CANFD/DoIP communication protocols. Some older vehicles use K-Line communication protocol, which may not be supported.
7.2.5. Is it necessary to re-ignite the car after the diagnostic system starts working?
For some vehicle conditions, re-ignition provides a more detailed analysis after OBD diagnosis.
8. User Tips
- The tool is designed for ease of use, potentially simplifying complex diagnostic tasks.
- Consider purchasing the optional HD software if you need to diagnose heavy-duty trucks (Class 4-8).
- The device supports both light and heavy-duty vehicles, expanding its utility for various automotive needs.
9. Warranty & Support
9.1. Warranty
This warranty is expressly limited to persons who purchase LAUNCH products for purposes of resale or use in the ordinary course of the buyer's business.
LAUNCH electronic products are warranted against defects in materials and workmanship for one year from the date of delivery to the user.
This warranty does not cover any part that has been abused, altered, used for a purpose other than for which it was intended, or used in a manner inconsistent with instructions regarding use. The exclusive remedy for any automotive meter found to be defective is repair or replacement, and LAUNCH shall not be liable for any consequential or incidental damages.
Final determination of defects shall be made by LAUNCH in accordance with established procedures. No agent, employee, or representative of LAUNCH has any authority to bind LAUNCH to any affirmation, representation, or warranty concerning LAUNCH automotive meters, except as stated herein.
9.2. Disclaimer
The above warranty is in lieu of any other warranty, expressed or implied, including any warranty of merchantability or fitness for a particular purpose.
9.3. Customer Service
If you have any questions on the operation of the unit, please contact the seller, or customer service center:
- Website: https://en.cnlaunch.com
- Phone: +86 755 2593 8674
- Email: DOD@cnlaunch.com
9.4. Statement
LAUNCH reserves the rights to make any change to product designs and specifications without notice. The actual object may differ a little from the descriptions in the manual in physical appearance, color and configuration. We have tried our best to make the descriptions and illustrations in the manual as accurate as possible, and defects are inevitable. If you have any question, please contact local dealer or after-sale service center of LAUNCH. LAUNCH does not bear any responsibility arising from misunderstandings.