Solar Charge Controller SY60, SY80, SY100

Contents

MPPT Solar Charge Controller Instruction Manual

Models: SY60, SY80, SY100

1. Product Overview

This MPPT Solar Charge Controller utilizes an advanced Maximum Power Point Tracking (MPPT) control algorithm to efficiently track the maximum power point of your photovoltaic (PV) array in any environmental condition. This ensures maximum energy extraction from your solar panels, significantly improving the energy utilization of your solar system.

It is suitable for various applications including communication base stations, home power supply systems, traffic lights, solar street lamps, and courtyard lamp systems.

Key Features:

  • Advanced MPPT maximum power point tracking technology with tracking efficiency no less than 99.5%.
  • LCD display dynamically shows operation data and working status.
  • Compatible with Seal, GEL, Flooded, and LiFePO4 battery types.
  • Dual USB 5V charging ports.
  • Automatic identification for 12V, 24V, 36V, and 48V battery systems.
  • Comprehensive protection features: Over-voltage, Over-current, Over-temperature.
  • Seven distinct working modes for versatile control.
  • Adjustable controller parameters.
  • Backlight display for enhanced visibility.
MPPT Solar Charge Controller with LCD display and dual USB ports
Figure 1: MPPT Solar Charge Controller with LCD display and dual USB ports.

2. Safety Precautions

  • Critical Warning: Do NOT connect the solar panel to the controller without first connecting the battery. The battery MUST be connected first to prevent damage to the controller.
  • Ensure the battery has sufficient voltage during initial installation for the controller to correctly identify the battery type (12V/24V/36V/48V).
  • Install the controller as close to the battery as possible to minimize voltage drop from excessive wire length, which can affect accurate voltage readings.
  • This controller is designed for various lead-acid batteries (open, sealed, GEL, etc.) and lithium batteries (LiFePO4). Lithium batteries may require manual adjustment of overcharge voltage. Do NOT use other battery types (e.g., nickel-metal hydride batteries).
  • Only use photovoltaic panels as the charging source. Do not use DC or other power sources.
  • The controller will generate heat during operation. Install it on a flat, well-ventilated surface to ensure proper cooling.

3. Installation and Setup

Connection Sequence:

  1. Connect the fully charged battery.
  2. Connect the PV (solar panel) system.
  3. Connect the DC load.

Disconnection Sequence:

  1. Disconnect the DC load.
  2. Disconnect the PV (solar panel) system.
  3. Disconnect the battery.

Wiring Diagram:

Follow the diagram below for correct wiring. Ensure all connections are secure and observe correct polarity to avoid damage.

Wiring diagram for SY6048 model solar charge controller, showing connections between solar panels, controller, battery, and DC load.
Figure 2: Typical wiring diagram for the solar charge controller (SY6048 model shown).
  • Connect the positive (+) and negative (-) terminals of the battery to the controller. The controller will automatically detect the battery voltage.
  • Connect the positive (+) and negative (-) terminals of the DC load to the controller. Be careful not to reverse the connection.
  • Connect the solar panel to the controller as shown in the diagram.

4. Operating Instructions

LCD Display Interface:

The LCD provides dynamic information about the system's status.

Detailed diagram of the LCD display interface and its indicators
Figure 3: At-a-glance display interface.
  1. Battery Work Status Display Area: Shows current battery voltage and status.
  2. Solar Panel Operating Status: Displays PV charging current.
  3. Load Output Status and Display Areas of All Parameters: Shows load current, product working temperature, and other parameters.
  4. Mode Control Display Area: Indicates the currently selected operating mode.
  5. Normal and Fault Status Display Area: Shows system status and any detected faults.

Charging Stages:

The controller employs a rapid, efficient, and safe battery charging algorithm with four stages:

Diagram illustrating the four charging stages: Bulk Charge, Boost Charge, Float Charge, Equalization Charge
Figure 4: Four Charging Stages.
  1. Bulk Charge: Initial stage where the battery accepts maximum current.
  2. Boost Charge: Charges the battery to a higher voltage to ensure full charge.
  3. Float Charge: Maintains the battery at a constant voltage to prevent self-discharge.
  4. Equalization Charge: Periodically overcharges the battery to balance cell voltages (for certain battery types).

Working Modes:

The controller offers 7 working modes, selectable via the interface:

Load working mode diagram showing Manual, Solar Light Control, and Solar Light Time Control modes
Figure 5: Load Working Modes.
  1. Charging Mode: The controller will only charge the battery and never discharge the load.
  2. Light Control Mode (Sunset On, Sunrise Off): When the controller detects nightfall, it will delay for ten minutes, then begin discharging to the load. When it detects daylight, it will delay for ten minutes, then stop discharging.
  3. Light and Time Delay Control Mode: Similar to Light Control Mode, but after detecting nightfall and the ten-minute delay, it starts discharging and initiates a countdown timer. Discharge stops when the timer reaches zero. The maximum delay duration is 23 hours and 59 minutes.
  4. Universal Control Mode: Under normal operating conditions (trouble-free), the controller continuously discharges to the load.
  5. Manual Control Mode: Use the '▼' button on the controller to manually toggle the load discharge on or off.
  6. Timing Control Mode: The controller will open or close the load discharge at regularly scheduled times.
  7. Test Mode: Functions similarly to Light and Time Delay Control Mode but with a fixed ten-minute delay.

Note on Low Voltage Protection: The controller will still discharge under low voltage protection. To override this, touch and hold the '▼' button for 5 seconds; discharge will continue. However, discharge can only be stopped manually in this state. Be aware that this action may damage the battery and should be used with caution.

5. Maintenance

  • Ventilation: Ensure the controller is installed in a well-ventilated area to dissipate heat generated during operation.
  • Connections: Periodically check all wiring connections for tightness and signs of corrosion. Loose or corroded connections can lead to poor performance or damage.
  • Cleanliness: Keep the controller clean and free from dust and debris. A buildup of dust can impede cooling and affect performance.
  • Battery Health: Monitor your battery's health and ensure it is compatible with the controller's settings.

6. Troubleshooting

Refer to the table below for common issues and their solutions:

Troubleshooting table for common solar charge controller faults
Figure 6: Troubleshooting Guide.
Fault PhenomenonPossible ReasonsExclusion Method
Sunny but not chargingPhotovoltaic panel open circuit or reverse connectionReconnect the photovoltaic panel
The load indicator is not litIncorrect mode settingReset the operating mode
The load indicator is not litBattery voltage too lowRecharge the battery
Load indicator flashes slowlyLoad overcurrentReduce the load power
Load indicator flashesShort circuit protectionRemove the short circuit, controller will automatically recover
The controller does not light upBattery voltage too low / reverse polarityReplace the battery / check reverse connection

7. Specifications

The controller is available in 60A, 80A, and 100A variants. Key specifications are detailed below:

Detailed product parameters table for 60A, 80A, and 100A models
Figure 7: Product Parameters and View Details.
ParameterSY60 (60A)SY80 (80A)SY100 (100A)
Battery Voltage12V/24V/36V/48V Auto
Rated Charging Current60A80A100A
Max PV Input Power (12V Battery)720W960W1200W
Max PV Input Power (24V Battery)1440W1920W2400W
Max PV Input Power (36V Battery)2160W2880W3600W
Max PV Input Power (48V Battery)2880W3840W4800W
PV Panel Input Voltage Range (Voc)15-23V (12V), 30-45V (24V), 45-69V (36V), 60-90V (48V)
Rated Output Current30A40A50A
USB Output Interface5V 2A (2 ports)
Product Size (L×W×H)195mm × 183mm × 68mm
Weight0.8kg0.85kg0.9kg
Operating Ambient Temperature0°C to 40°C
Storage Ambient Temperature-15°C to 50°C
Humidity0-90% (without condensation)
Charging MethodMPPT Pulse Width Modulation Charging
Cooling MethodSelf-cooling heat sink

8. User Tips

  • For optimal performance, ensure your battery is adequately charged before the initial connection to allow the controller to correctly identify the system voltage (12V/24V/36V/48V).
  • Always install the controller in a location with good airflow to prevent overheating, as it uses a self-cooling heat sink.
  • Double-check all wiring connections for correct polarity and tightness to avoid system malfunctions or damage.
  • Regularly monitor the LCD display for system status and any fault indications to ensure continuous and efficient operation.

9. Warranty and Support

This product is CE certified. For any technical support, troubleshooting assistance beyond this manual, or warranty inquiries, please contact the seller or manufacturer directly. Keep your purchase records for reference.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.