1. Important Safety Information
This manual is intended primarily for use by professional bicycle mechanics. Users who are not professionally trained for bicycle assembly should not attempt to install the components themselves. If any part of the information is unclear, contact your place of purchase or a local bicycle dealer for assistance.
- Always read all instruction manuals included with the product.
- Do not disassemble or modify the product other than as stated in this manual.
- All dealer's manuals and instruction manuals can be viewed online at http://si.shimano.com.
- Observe all applicable rules and regulations of your country, state, or region.
- DANGER: Failure to follow instructions may result in death or serious injury.
- WARNING: Failure to follow instructions could result in death or serious injury.
- CAUTION: Failure to follow instructions could cause personal injury or physical damage to equipment and surroundings.
General Safety Precautions:
- Use genuine Shimano parts only. Loose or damaged parts can lead to serious injury.
- Wear safety glasses or goggles when performing maintenance.
- Learn proper braking technique for your bicycle model. Improper use can lead to loss of control or falls.
- Applying the front brake too strongly can lock the wheel and cause falls.
- Always ensure front and rear brakes are working correctly before riding.
- Braking distance is longer in wet weather; reduce speed and apply brakes early and gently.
- Wet road surfaces increase skid risk; reduce speed and apply brakes early and gently.
- Do not alter carbon levers; they may break.
- Check for damage (peeling, cracking) on carbon levers before riding.
- Grease the inner cable and inside of the outer casing before use. Use SIS SP41 grease (Y04180000) if needed. Prevent soil and dirt adhesion.
- Use special grease for shifting cables. Other greases may impair shifting performance.
- If shifting adjustments fail, check rear fork alignment, cable lubrication, and outer casing length.
A user manual (PDF) with detailed diagrams and instructions is available for reference: View User Manual PDF.
2. Product Overview
The SHIMANO CLARIS R2000 Groupset is designed for 2x8 speed road bike applications, offering reliable and smooth mechanical shifting performance. This groupset includes key components for a complete drivetrain setup.
Components Included:
- ST-R2000 Dual Control Levers: 2x8 Speed shifters and brake levers combined.
- FD-R2000 Front Derailleur: Available in Braze On and Clamp mounting types.
- RD-R2000 Rear Derailleur: Available in GS (long cage) and SS (short cage) options.
- CN-HG40 Chain: 6-8 Speed compatible.
- SUNSHINE Cassette: Available in 11-28T, 11-30T, 11-32T, and 11-34T options.
3. Specifications
| Attribute | Specification |
|---|---|
| Brand Name | SHIMANO |
| Model Number | R2000 |
| Gears | 8 Speed |
| Material | Alloy |
| Components | Derailleurs |
| Derailleur Groupset Type | Mechanical Derailleur system |
| High-concerned chemical | None |
| Cassette Options | 11-28T, 11-30T, 11-32T, 11-34T |
| Chain | CN-HG40 (6-8 Speed) |
4. Setup and Installation
4.1. Tools Required
- 2mm Hexagon wrench
- 4mm Hexagon wrench (for RAPIDFIRE Plus)
- 5mm Hexagon wrench
- Screwdriver (#1, #2)
- TL-CT12 Cable cutter
- Plastic mallet
- Shimano original E-ring removal tool (Y6RT66000/Y6RT68000)
4.2. Installation to Handlebar (ST-R2000 Dual Control Lever)
- Turn over the bracket cover from the back side. Gently turn over the ends of the bracket cover with both hands and slowly push them down. (Refer to diagram in official manual showing bracket cover being peeled back).
- Use a 5mm hexagon wrench to tighten the clamp bolt at the top of the bracket. The tightening torque should be 6-8 N-m. (Refer to diagram in official manual showing wrench tightening clamp bolt).
Note: Forcibly pulling the bracket cover may cause damage. Ensure proper torque to prevent damage to carbon handlebars.
4.3. Installation to Handlebar (SL-R2000/SL-R2030 RAPIDFIRE Plus Shifting Lever)
- Use a handlebar grip with a maximum outer diameter of Ø36mm or less.
- Tighten the clamp bolt using a 4mm hexagon wrench. The tightening torque should be 3-5 N-m. (Refer to diagram in official manual showing wrench tightening clamp bolt).
Note: When installing to carbon frames/handlebars, verify the appropriate torque with the bicycle or frame manufacturer to avoid damage or inadequate fixing force. Install in a position where brake and gear shifting operations are not obstructed.
4.4. Installation of Brake Cable (ST-R2000 Dual Control Lever)
Caution: Be careful not to let the BC-9000/BC-R680 inner cable come into contact with the shifting lever or the metal section (adjustment section) of the caliper brake. Damage to the inner cable coating may occur but will not affect function.
- Use a cable with sufficient length to spare when handlebars are turned fully.
- Cable Used: Inner cable Ø1.6mm, Outer casing Ø5mm.
- Depress the lever as if to brake and pass the brake cable through. (Refer to diagram in official manual showing cable routing through the lever).
- Temporarily secure the outer casing to the handlebar using tape or similar material. (Refer to diagram in official manual showing outer casing secured to handlebar).
Note: Ensure the inner end is firmly set in the cable hook. For detailed brake cable installation, refer to the brake's dealer manual.
4.5. Installation of Brake Cable (SL-R2000/SL-R2030 RAPIDFIRE Plus Shifting Lever)
- Use a cable with sufficient length to spare when handlebars are turned fully.
- Cable Used: Inner cable Ø1.6mm, SLR outer casing Ø5mm.
Install the brake cable as shown in the official manual's figure, routing it through the lever body. (Refer to diagrams [1], [2], [3] in official manual showing brake cable routing).
4.6. Installation of Shifting Cable (ST-R2000 Dual Control Lever)
- Cable Used: Dedicated inner cable Ø1.2mm, Recommended outer casing Normal outer cap/SP41 outer casing Ø4mm (SHIMANO SP41).
Note: Do not let dust adhere to the inner cable. If grease is wiped off, apply SIS SP41 grease (Y04180000).
Outer Cap Installation Position:
- Derailleur side: Normal outer cap.
- Shifting lever side: Outer cap with short tongue.
- Use sealed outer cap (resin type) for optimal protection.
Tip: Insert the convex shape on the cap into the groove in the bracket.
Cutting the Outer Casing:
- Use a TL-CT12 cable cutter or equivalent tool to cut the side opposite the inscription. (Refer to diagram in official manual showing cable cutter).
- After cutting, expand the tip of the liner (Ø2.2 or more) with TL-CT12 or another narrow tool. Arrange the cut end into a perfect circle. (Refer to diagram in official manual showing liner expansion).
- Insert the outer casing until it touches the seating surface of the outer cap. Install the outer cap. (Refer to diagram in official manual showing outer casing insertion).
Note: Be careful not to crush the convex section of the tip when inserting the outer casing.
Passing Through the Shifting Inner Cable:
- Operate the lever (B) and set it to the top position. Attach the cable and make adjustments. (Refer to diagram in official manual showing lever operation).
- Remove the cable cover using a slotted screwdriver or similar flat-tipped tool. (Refer to diagram in official manual showing cable cover removal).
- Put the inner cable through as shown in the illustration. (Refer to diagram in official manual showing inner cable routing).
- Insert the cable so that the inner end is attached to the unit. (Refer to diagram in official manual showing inner end attachment).
- Put the inner cable through as shown in the illustration. (Refer to diagram in official manual showing final inner cable routing).
- Finally, reinstall the cable cover. (Refer to diagram in official manual showing cable cover reinstallation).
- Temporarily secure the outer casing to the handlebar using tape or similar material. (Refer to diagram in official manual showing outer casing secured to handlebar).
- Wrap the handlebar with handlebar tape.
Note: When the inner cable is installed, coating may be damaged and become fluffy; however, it will not affect function.
5. Operating Instructions
The SHIMANO CLARIS R2000 groupset provides intuitive and precise mechanical shifting. To operate the gears, use the dual control levers (ST-R2000) or RAPIDFIRE Plus shifters (SL-R2000/SL-R2030) as follows:
- Shifting Up (to a larger cog/chainring): Push the main lever inwards.
- Shifting Down (to a smaller cog/chainring): Push the smaller release lever inwards.
- Braking: Pull the main lever towards the handlebar.
Always ensure you are pedaling while shifting gears for smooth operation. Avoid shifting under heavy load.
6. Adjustment
6.1. Lever Stroke Adjustment (ST-R2000 Dual Control Lever)
- Adjust the lever stroke using a 2mm hexagon wrench. (Refer to diagram in official manual showing adjustment screw location).
- Turning clockwise (x) makes the lever stroke smaller.
- Turning counterclockwise (y) makes the lever stroke larger.
Note: Make sure braking operates properly after the adjustment.
6.2. Lever Stroke Adjustment (SL-R2000/SL-R2030 RAPIDFIRE Plus Shifting Lever)
- Adjust the lever stroke using a 2mm hexagon wrench. (Refer to diagram in official manual showing adjustment screw location).
- Turning clockwise makes the lever stroke smaller.
- Turning counterclockwise makes the lever stroke larger.
7. Maintenance
7.1. ST-R2000 Dual Control Lever Maintenance
Disassembling the Bracket Body and Lever Body:
- First, use the Shimano original E-ring removal tool (Y6RT66000/Y6RT68000) to remove the E-ring. Align the tool with the E-ring and set part [A] against the E-ring to remove it. (Refer to diagram in official manual showing E-ring removal).
- Caution: The E-ring may pop out; wear protective glasses.
- Insert a hexagon wrench or similar tool into the lever axle hole. Tap it gently with a plastic mallet to push out the lever axle, separating the bracket body and lever body. (Refer to diagram in official manual showing lever axle removal).
Note: Always remove the lever axle in this direction. Removing it in the opposite direction may damage the bracket body.
Assembling the Bracket Body and Lever Body:
- Insert the lever into the bracket.
- Insert the end of the return spring into the notch.
- Align the axle holes, set the Shimano original E-ring removal tool [1] in position, then press-fit the lever axle. (Refer to diagram in official manual showing lever axle insertion).
- Note: Do not press-fit the lever axle from the opposite direction, as it may cause damage. Ensure the E-ring groove faces up and the bracket body surface is flat for proper E-ring fit.
- Remove the Shimano original E-ring removal tool [1], then use tool [2] to install a new E-ring.
Note: Do not reuse the removed E-ring.
Replacing the Bracket Cover:
- Insert the protrusions on the bracket cover into the hollows in the bracket body when fitting.
- Always replace the bracket cover with the lever removed from the bicycle.
Tip: Wipe a little rubbing alcohol inside the bracket cover to make installation easier. The bracket cover has an engraved label (R for right, L for left).
Replacing the Name Plate:
- Operate the shifting lever while operating the brake lever to expose the screws.
- Remove the screws using a #1 screwdriver, then replace the name plate.
- Tighten the screws to 0.15-0.2 N-m. (Refer to diagram in official manual showing name plate screw location).
Replacing the Main Lever Support:
- Operate lever [B] two or more times, then lever [A] by two gears.
- Hold the base of lever [A] and return only lever [A] to its original position. (Refer to diagram in official manual showing lever operation).
- Rotate the main lever support in the direction of the arrow with a slotted screwdriver or equivalent tool, and then remove the stopper.
- Pull out the old main lever support.
- Insert a new main lever support. (Refer to diagrams in official manual for visual guidance).
Replacing the SL Cable Guide:
- Remove the lever from the handle, then remove the bracket cover.
- Remove the cable cover.
- Use a pointed tool to pry out the SL cable guide. (Refer to diagram in official manual showing cable guide removal).
- Push in the new SL cable guide with your hands.
- Install the cable cover.
Replacing the Cable Cover:
- Remove the cable cover from the bracket using a screwdriver and pull the cable out with your hand. (Refer to diagram in official manual showing cable cover removal).
- Before installing a new cable cover, make a slight crease on it and insert it into the hole in the bracket.
How to Pull Out a Disconnected Inner End (Shifting Cable):
- Remove the lever from the handle, then remove the bracket cover.
- Remove the screw located at the bottom of the bracket using a #1 screwdriver, and then remove the unit cover. (Refer to diagram in official manual showing screw and unit cover removal).
- Pull out the inner end from the cable hook of the winding body.
- Note: Be careful not to touch the spring accidentally, as this could cause a malfunction. (Refer to diagram in official manual showing spring location).
- Reattach the unit cover and tighten the screws to 0.2-0.25 N-m.
Tip: If the inner cable breaks, it is recommended to replace the cable guide along with the inner cable for smooth shifting.
7.2. SL-R2000/SL-R2030 RAPIDFIRE Plus Shifting Lever Maintenance
Replacing the Inner Cable:
- Refer to SIS Adjustment in the Rear Derailleur section of General Operations for information on installation to the derailleur and necessary adjustments.
- Recommended Inner Cables: Outer casing OT-SP41 with OPTISLICK material/surface treatment.
- Operate the release lever to set the chain on the smallest chainring/smallest sprocket. (Refer to diagram in official manual showing release lever position).
- Remove the wire end hooking cap and install the new inner cable. (Refer to diagram in official manual showing wire end hooking cap removal).
- Install the wire end hooking cap by turning it until it stops. Do not overtighten.
Note: If an indicator unit is present, check the position of the pointer on the indicator. The number of release lever operations varies by speed (e.g., 8-speed requires 7 or more times).
Replacement and Reassembly of the Indicator Unit:
Note: Disassembly and assembly should only be carried out when removing or replacing the indicator unit.
Disassembly:
- Operate the release lever to set the chain on the smallest chainring/smallest sprocket.
- Remove the wire end hooking cap and install the cable.
- After removing the main lever cover, remove the 3 indicator fixing screws (long and short) using #1 and #2 screwdrivers. (Refer to diagram in official manual showing screw locations).
- Remove the indicator unit.
Assembly:
- Operate the release lever to set the chain on the smallest chainring/smallest sprocket.
- Check the position of the pointer on the indicator (front: right end, rear: left end).
- Install the indicator unit.
- Tighten the 3 indicator fixing screws and then attach the main lever cover.
- Tighten indicator fixing screw (long) to 0.3-0.6 N-m.
- Tighten indicator fixing screw (short) to 0.2-0.4 N-m.
- Tighten cover fixing screw to 0.1-0.3 N-m.
- Check that it is operating correctly. If not, reassemble paying attention to steps 1-4.
8. Troubleshooting
- Rough Shifting: If gear shifting operations do not feel smooth, wash the derailleur and lubricate all moving parts.
- Shifting Adjustment Issues: If gear shifting adjustments cannot be carried out, check that the rear fork ends are aligned. Also, verify that the cable is lubricated and clean, and that the outer casing is neither too long nor too short.
9. User Tips
No specific user tips are available from provided reviews or Q&A content at this time.
10. Warranty and Support
For support and inquiries, please contact the appropriate regional office:
- SHIMANO NORTH AMERICA BICYCLE, INC.
One Holland, Irvine, California 92618, U.S.A.
Phone: +1-949-951-5003 - SHIMANO EUROPE B.V.
High Tech Campus 92, 5656 AG Eindhoven, The Netherlands
Phone: +31-402-612222 - SHIMANO INC.
3-77 Oimatsu-cho, Sakai-ku, Sakai-shi, Osaka 590-8577, Japan
Please note: Specifications are subject to change for improvement without notice.