ToolKitRc M6DAC V2

Contents

ToolkitRC M6DAC V2 Charger User Manual

Manual V1.0 - 2025.04

ToolkitRC M6DAC V2 Charger with packaging and cables

ToolkitRC M6DAC V2 Charger and accessories

1. Introduction

Thank you for purchasing the ToolkitRC M6DAC Pro/V2 dual balance charger. Please read this manual carefully before use to ensure proper operation and safety.

Key Points

  • Tips: Helpful advice for optimal use.
  • Important: Critical information for safety and functionality.
  • Information: General details about features and settings.

Further Information

To ensure you have the best experience with this product, please visit www.toolkitrc.com for news, information, and firmware updates for your charger.

2. Safety Instructions

Failure to follow these safety instructions may result in fire, property damage, or injury.

  1. The M6DAC Pro/V2 allows an input voltage of 7-28V DC or AC 100-240V. Ensure the power supply voltage is within this range. Pay attention to the positive and negative polarities when connecting.
  2. Do not use this product in a hot area, near a heat source, or in a damp, flammable, or explosive gas environment.
  3. Only use this product under direct supervision. Do not leave charging batteries unattended.
  4. When not using this product, unplug the input power.
  5. When using the charging function, set the current to match the battery. Do not set excessive current to avoid damaging the battery.

3. Product Overview

The ToolkitRC M6DAC Pro/V2 is a dual-channel balanced charger with a compact size, high power density, and innovative design, offering charging accuracy as low as 5mV.

Key Features:

  • Built-in AC power supply: 200W (V2) / 300W (PRO).
  • Supports charge, discharge, and balance management for LiPo, LiHV, LiFe, Lion, LTO (1-6S), NiMh (1-16S), and PB (1-10S) batteries.
  • Charging current: Synchronous mode max 28A@MAX700W; Asynchronous mode max 16A@MAX400W.
  • Discharge current: Recycle mode max 16A@400W *2; Bridge mode max 16A@400W (recommended power resistor 2-5 Ω); Normal mode max 3A@15W *2.
  • 65W fast charge USB-C output with PD/QC/AFC/FCP/SCP/PE/SFCP/etc. full protocol.
  • Built-in wireless charging (PRO version only).
  • Adjustable Lithium battery cut-off voltage (TVC function).
  • Constant current and constant voltage output: customizable 1-28V constant voltage, 1-16A constant current.
  • Adapts to mainstream UAV batteries, automatically activating and charging.
  • Multi-language system with arbitrary language upgrades.
  • Firmware upgrades via USB drive (copy and paste files).

M6DAC Pro/V2 Layout

Front view of M6DAC V2 with display, scroll wheel, and ports labeled
Figure 3.1: Front Panel Layout (Display, Exit/CH Key, Scroll Wheel, Balance Ports, Temp. Sensor Port, Main Ports, States LED)
Back view of M6DAC V2 with AC/DC inputs, USB-C output, and cooling fan labeled
Figure 3.2: Back Panel Layout (AC Input, Cooling Fan, USB-C Output, DC Input)

4. Setup: Quick Start Guide

  1. Connect a 7-28V DC or AC 100-240V power supply or input battery to the input port on the back of the M6DAC Pro/V2.
  2. The display will show the boot logo for 2 seconds, accompanied by a boot sound.
  3. After booting, the display will enter the main interface, showing charging status and parameters.
  4. Short press the [Exit/CH] key to switch the cursor between the left and right channels.
  5. Press and hold [Exit/CH] to start testing the internal resistance of the corresponding channel. The internal resistance will be displayed after the test.
  6. Scroll the [Scroll Wheel] to switch between pages in the corresponding channel.
  7. Short press [OK] to select a charging task when the channel is idle, or to adjust and end a task when the channel is working.
  8. Press and hold [OK] to enter the system setting interface when both channels are idle.
  9. Press [Exit] to end modification or return to the previous interface.

Button Operations:

  • Scroll Wheel (Short Press): Confirm the key function.
  • Scroll Wheel (Press and Hold for 2 seconds): Delete the key function.
  • A 'di-di' prompt tone indicates successful key operation.

5. Operating Instructions: Charge and Discharge Settings

Short press [OK] on the main interface to enter the charging function settings. Use the [Scroll Wheel] to navigate and [OK] to select/confirm.

5.1. Battery Type Selection

Move the cursor to [Battery Type] and press [OK] to modify. The charger supports LiPo, LiHV, LiFe, Lion, LTO, NiMh, and PB batteries. Power supply and smart battery options are also available.

Warning: Choosing the wrong battery type may damage the battery, the charger, and poses a risk of burning. Do not use this product to charge batteries that do not indicate their type.

Glossary of Battery Terms:

  • LiPo: Lithium polymer battery, nominal 3.70V, fully charged 4.20V.
  • LiHV: High-voltage lithium battery, nominal 3.85V, fully charged 4.35V.
  • LiFe: Iron-lithium battery, nominal 3.30V, fully charged 3.60V.
  • Lion: Lithium-ion battery, nominal 3.60V, fully charged 4.10V.
  • LTO: Lithium titanate battery, nominal 2.40V, fully charged 2.70V.
  • NiMh: Nickel-metal hydride battery, nominal 1.20V.
  • PB: Lead-acid battery, nominal 2.00V.

5.2. Number of Cells

Move the cursor to [Battery cell Number] and press [OK] to modify. When set to [Auto], the charger automatically recognizes the number of connected battery cells. For optimal accuracy, especially with Lixx batteries, connect to the balance port.

Tip: Over-discharging or over-charging can lead to incorrect cell number recognition. Manually set the correct cell number if needed.

5.3. Mode Selection

Move the cursor to [Mode] and press [OK] to select the working mode:

  • Charge
  • Discharge
  • Storage
  • Destroy

LiPo, LiHV, LiFe, Lion batteries support Charge, Discharge, Cycle, Destroy, and Storage. NiMh batteries support Charge, Discharge, Cycle. PB batteries support Charge and Discharge.

Warning: Destroy mode clears electrical energy and should only be used when discarding batteries. Improper use may cause irreversible damage to lithium batteries.

5.4. Discharge Mode

When Discharge, Storage, or Cycle mode is selected, the battery setting interface will show discharge mode options:

  • Inter (Internal) Mode: Discharges through internal heat consumption, max 3.0A@15W.
  • Recycle Mode: Recovers electrical energy from the discharging battery to the input battery (requires suitable battery as input).
  • Bridge Mode: Dissipates electrical energy through a power resistor. Connect the discharging battery to one channel and the power resistor (recommended 2-5Ω, 100-500W) to another channel. Note: Input power supply requires an adapter.

5.5. Input MaxVoltage

When Recycle discharge mode is selected, set the [Input MaxVoltage]. If the input voltage reaches this value during discharge, the discharge will stop.

Tip: Set the input cut-off voltage within the safe range of the power supply battery. A high over-voltage setting may damage the input power battery.

5.6. End Voltage (TVC)

Modify the end voltage of a single battery. For charging, it's the charging cut-off voltage; for discharging, it's the discharge cut-off voltage. Adjust in 0.01V steps. Range is +/- 50mV of full voltage.

Tip: Only LiPo, LiHV, LiFe batteries can set end voltage. Do not modify if unfamiliar with battery characteristics. TVC stands for Terminal Voltage Control.

5.7. Current Setting

Modify [Charge Current] or [Discharge Current]. Rotate the [Scroll Wheel] to adjust in 0.1A steps. Max charge current is 16.0A (28A in synchronous mode).

Tip: Set charging rate to 1-2C of battery capacity (e.g., 2.0-4.0A for a 2000mAh battery). Current settings are only valid in the corresponding working mode.

5.8. NiMH Setting (PeakV)

For NiMh batteries, set the negative pressure value (PeakV) when the battery is fully charged. The range is 3mV-15mV.

Glossary: PeakV refers to the voltage drop when the nickel-metal hydride battery is fully charged.

5.9. Cycle Setting

For NiMh batteries, when Cycle mode is selected, set the number of cycles (2-12) and rest time (2-10 minutes). The charger will follow a Discharge -> Charge pattern.

5.10. Power Mode Setting

When the battery type is 'Power', only output voltage (1-28V) and maximum current (0.5-16A) can be set.

5.11. Smart Battery

For 'Smart Battery' type, select the drone model (e.g., Mavic2, MavicS, Phantom, Inspire) and set the maximum current.

5.12. Synchronous Mode

In the system settings, enabling synchronous mode allows two channels to charge the same battery with a total current of 28A.

M6DAC V2 in synchronous charging mode with two batteries connected
Figure 5.1: Synchronous Charging Setup

5.13. Charge and Discharge Work

When charging or discharging starts, the charger enters the working interface, displaying input power supply voltage, total power consumption, charger internal temperature, USB-C output voltage/current, main port voltage/current, working time, cumulative capacity, and battery cell voltages.

Rotate the [Scroll Wheel] to switch between bottom status information and internal resistance voltage values. Short press [OK] to dynamically set the working current or stop working.

To end work, short press [OK], move the cursor to [Stop working], and press [OK] again. A prompt box and tone will indicate completion or error.

Important Tips for Charging/Discharging:

  • Always supervise the process to address abnormalities.
  • For lithium batteries, connecting only to the main port will not perform balance management. Use the balance lead for proper balance management.
  • After charging, unplug the battery and connect a new one. The charger can automatically continue charging/discharging if 'Continuous work mode' is selected. Ensure the new battery matches the settings or manually adjust.

6. Maintenance

6.1. General Care

  • Keep the charger clean and free from dust. Use a soft, dry cloth for cleaning.
  • Avoid exposing the charger to extreme temperatures, humidity, or direct sunlight.
  • Ensure proper ventilation around the charger, especially the cooling fan, to prevent overheating.
  • Store the charger in a safe place when not in use, away from children and pets.

6.2. System Settings

Long-press [OK] on the main interface when channels are idle to enter system settings:

  • Input settings: Configure power selection (P1, P2, P3 presets), power type (Battery/AC), max power, max current, and voltage range.
  • Security settings: Set safe internal/external temperatures, safe time, and safe capacity to prevent over-charging/discharging.
  • Synchronous mode: Enable/disable synchronous operation for dual-channel charging.
  • Continuous work: Enable/disable automatic continuation of charging/discharging for the next connected battery.
  • Work completed: Choose whether to stop or trickle charge after completion.
  • Balance start volt: Set the voltage at which balancing begins.
  • Battery selection: Enable/disable battery selection feature.
  • Backlight: Adjust display backlight brightness (1-10 levels).
  • Buzzer: Set the tone of the buzzer.
  • Language: Select system display language (English, Chinese, etc.).
  • Default: Restore all settings to factory defaults.

7. Troubleshooting

7.1. Firmware Upgrade

Connect the M6DAC Pro/V2 to a computer via the included USB cable. The computer will recognize it as a USB disk named 'Toolkit'. Download the `app.upg` firmware file from the official ToolkitRC website and copy/paste it to overwrite the existing file on the USB disk to upgrade the firmware.

7.2. Manual Voltage Calibration

In the shutdown state, press and hold the [Scroll Wheel] while connecting the power supply. The system will enter the manual calibration voltage function. Measure the actual voltage of each battery with a voltmeter, then adjust the corresponding voltage value on the charger to match. Save the calibration by moving the cursor to 'save' and short pressing. A beep confirms success.

7.3. Fan Operation

The cooling fan operates at half-speed when the internal temperature exceeds 45°C to reduce noise. It switches to full-speed airflow when the temperature exceeds 53°C to enhance heat dissipation.

7.4. Fully Charged Indication

When a lithium battery is fully charged, the charger will prompt "Fast charging has ended". If the battery is not removed, constant voltage trickle charging will automatically continue to ensure the battery is fully charged.

7.5. Wireless Charging (PRO version only)

The M6DAC Pro features a built-in wireless charging module that automatically adapts and charges compatible mobile devices placed on top, with a charging power of 10W.

7.6. USB-C 65W Output

The USB interface can output 65W to charge mobile devices, supporting various fast charge protocols including PD3.0/PD2.0, PPS, QC4/QC3.0/QC2.0, AFC, FCP, SCP, PE2.0/PE1.1, and SFCP/VOOC.

7.7. Automatic Continuous Charge/Discharge

If 'Continuous work mode' is enabled in the settings, when a battery is fully charged, unplug it for 2 seconds, then connect the next battery. The device will automatically continue the charge/discharge cycle.

8. Specifications

Category Parameter Value
InputDC Input7-28V@MAX30A
AC Input (V2)100-240V@MAX200W
AC Input (PRO)100-240V@MAX300W
Battery TypeSupported TypesLiPo, LiHV, LiFe, Lion, LTO (1-6S), NiMh (1-16S), Pb (1-10S)
Bal. Cur.Balance Current1000mA @2-6S
AccuracyVoltage Accuracy<0.005V
Charging PowerAsynchronous0.1-16A@400W *2
Synchronous0.1-28A@700W
Discharging PowerRecycle Mode0.1-16A@400W *2
Bridge Mode0.1-16A@400W
Normal Mode0.1-3A@15W *2
USB-C OutputPower65W@20V@3.25A
ProtocolSupported ProtocolsPD, QC, AFC, FCP, SCP, PE, SFCP, VOOC
Wireless ChargingPower (Pro Only)10W
Battery VoltageRange1.0V-5.0V @1-6S
Battery Internal ResistanceRange1-100mR @1-6S
DisplayTypeIPS 2.8 inch 320*280 resolution
Product SizeDimensions116mm*112mm*63mm
Product WeightWeight600g (Pro), 570g (V2)
Individual Packing SizeDimensions164mm*135mm*68mm
Individual Packing WeightWeight730g (Pro), 700g (V2)

9. User Tips

  • The M6DAC V2 is a compact yet powerful charger, ideal for various RC battery types.
  • Ensure all connections are secure and correct polarity is observed before starting any charging or discharging process.
  • Always monitor batteries during charging, especially when using high currents or unfamiliar battery types.
  • Take advantage of the USB-C output for convenient charging of other devices.
  • Keep the firmware updated by visiting the official ToolkitRC website for the latest features and improvements.

10. Warranty and Support

For warranty information, technical support, and service inquiries, please visit the official ToolkitRC website at www.toolkitrc.com or contact your local distributor. Please retain your proof of purchase for warranty claims.

A PDF version of this manual is available for download at ToolkitRC M6DAC Pro/V2 User Manual (PDF).

11. Product Video Overview

Watch this video for a visual demonstration of the ToolkitRC M6DAC V2 charger's features and operation.

Video: ToolkitRC M6DAC V2 Product Features

© ToolkitRC 2025. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.