GRN-FLASHING EU-E27

Contents

E27 Hanging Indoor Plants Light Holder Instruction Manual

Model: EU-E27 (Available with EU or US Plug, and 2m, 4m, or 9m cable lengths)

Brand: GRN-FLASHING

1. Introduction

This manual provides essential information for the safe and effective use of your E27 Hanging Indoor Plants Light Holder. Please read all instructions carefully before installation and operation to ensure proper function and to prevent damage or injury.

2. Safety & Warnings

Important Safety Information:

Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.

Warning:

  • Keep the device and its cord out of reach of children under 3 years old.
  • Keep away from children unless supervised by an adult.
  • Do not use this product for purposes other than its intended use.
  • Inspect the product before each use; do not use if damaged.
  • Follow installation and operation guidelines to avoid injury.
  • Do not expose to water or moisture.
  • Handle with care to avoid cuts or injuries.

3. Product Overview

The E27 Hanging Light Holder is designed for versatile lighting applications, including plant growth and general indoor use. It features a convenient on/off switch and is compatible with standard E27 bulbs (bulb not included).

Key Features:

  • Convenient On/Off Switch: Easy control of your lighting.
  • Lightweight & Easy to Install: Simple setup and portability.
  • Plug Compatibility: Available with EU or US plug types for reliable power connection.
  • Versatile Use: Compatible with E27 bulbs for various lighting needs, such as plant growth, home, or office use.

Components:

  • E27 Lampholder with integrated on/off switch
  • Power cable (2m, 4m, or 9m length)
  • EU or US plug type
E27 Lampholder with EU plug and coiled cable
Figure 1: E27 Lampholder with EU plug and coiled cable.
E27 Lampholder with US plug and coiled cable
Figure 2: E27 Lampholder with US plug and coiled cable.
Close-up of the E27 screw interface
Figure 3: Close-up view of the E27 screw interface.

4. Setup and Installation

  1. Unpack: Carefully remove the light holder from its packaging. Inspect for any damage upon arrival. Do not use if damaged.
  2. Check Voltage: First, verify that the voltage of your power supply matches the product's specifications (AC85-265V).
  3. Insert Bulb: Screw an E27 bulb (not included) into the lampholder until snug. Do not overtighten.
  4. Connect Plug: Connect the corresponding plug (EU or US) to a suitable power outlet. Ensure the plug is fully inserted. Pay attention to any signs such as small arrows, "+" and "-" for one-to-one connection if applicable for specific plug types.
  5. Positioning: Hang the light holder in the desired location. The integrated loop on the lampholder can be used for hanging.
Application display showing an E27 screw interface for various light bulbs, including a blue light, a warm white light, and a pink light.
Figure 4: Example applications of the E27 screw interface with various light bulbs.

5. Operating Instructions

Once the light holder is installed and a bulb is inserted, operate it using the integrated on/off switch located on the lampholder. Press the switch to turn the light on or off.

Close-up of the red on/off switch on the E27 lampholder
Figure 5: Detail of the on/off switch on the lampholder.

6. Maintenance

  • Cleaning: Disconnect from power before cleaning. Wipe the lampholder and cable with a dry, soft cloth. Do not use abrasive cleaners or liquids.
  • Inspection: Periodically check the cable and lampholder for any signs of wear, damage, or loose connections. If any damage is found, discontinue use immediately and replace the product.
  • Bulb Replacement: Ensure the power is off and the bulb has cooled before replacing. Screw in a new E27 bulb.

7. Troubleshooting

Problem Possible Cause Solution
Light does not turn on
  • No power to the outlet.
  • Bulb is faulty or not screwed in properly.
  • Switch is off.
  • Cable or lampholder is damaged.
  • Check the power outlet with another device.
  • Ensure the bulb is screwed in tightly and try a new bulb.
  • Toggle the on/off switch.
  • Inspect for damage; if damaged, discontinue use and replace.
Loose connection / Unstable light
  • Bulb not fully seated.
  • Plug not fully inserted.
  • Internal wiring issue.
  • Ensure bulb is securely screwed in.
  • Push the plug firmly into the outlet.
  • If issues persist, discontinue use and replace.

8. Specifications

Attribute Value
Product NameE27 Hanging Indoor Plants Light Holder
Model NumberEU-E27
Brand NameGRN-FLASHING
Item TypeLamp Bases
MaterialFireproof ABS, Metal + Plastic
Base MaterialBrass, Plastic
Base TypeE27
Plug TypeEU / US Plug
VoltageAC85-265V
Max Power100W
Wire Length OptionsApprox. 2.1m / 4m / 9.1m
Body ColorWhite
CertificationCE, RoHS
Compliance StandardsEN IEC 62311:2020, EN IEC 60598-2-1:2021, EN IEC 60598-1:2021 + AMD11:2022, ETSI EN 301 489-1 V2.2.3 (2019-11), ETSI EN 301 489-17 V3.2.4 (2020-09), ETSI EN 300 328 V2.2.2 (2019-07), EN IEC 63000:2018
Working Voltage (DC connector, from PDF)0-24V
Maximum Current (DC connector, from PDF)2-4A
Working Environment (from PDF)-40°C to +90°C

9. User Tips

  • Secure Connections: Ensure the bulb is screwed in firmly and the plug is fully inserted into the outlet to prevent loose connections and potential hazards.
  • Cable Management: While the cable is long, consider using cable ties or clips to manage excess length and prevent tripping hazards, especially in high-traffic areas.
  • Regular Inspection: Periodically check the cable and lampholder for any signs of wear, damage, or loose connections, particularly if the cable is frequently moved or adjusted.
  • Bulb Type and Wattage: This holder is compatible with E27 bulbs. Choose a bulb appropriate for your intended use (e.g., grow light for plants, LED for energy efficiency) and ensure it does not exceed the maximum power rating of 100W to prevent overheating.

10. Warranty and Support

This product comes with a 1-year warranty from the date of purchase.

For support or warranty claims, please contact the manufacturer or your retailer. Refer to the following manufacturer information:

Manufacturer Information:

Attribute Detail
NameShenzhen Lvseshuxing Technology Co., LTD
Address708, Floor 7, Unit 2, Building B, Xinglongfu Chuangke Park, Yousong Road, Yousong Community, Longhua Street, Longhua District, Shenzhen
Zip Code518110
Contact PersonYiQi Wen
Tel18820779209
E-mail52680771@qq.com

EU Authorized Representative:

Attribute Detail
NameGAVIMOSA CONSULTORIA, SOCIEDAD LIMITADA
AddressCASTELLANA 9144, 28046 Madrid
Contact PersonJorge Wilson
Tel+34 696313170
E-mailcompliance.gavimosa@outlook.com

A PDF user manual is available for download: View User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.