YSRSAI YSR-CGD-RGB

Contents

Dimmable Single Color COB LED Light Strip Instruction Manual

Model: YSR-CGD-RGB | Brand: YSRSAI

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your Dimmable Single Color COB LED Light Strip. This product features a V1 LED Dimmer controller and an R11 RF Wireless Remote Control, offering smooth 0-100% dimming without flickering. The COB LED strip provides uniform, continuous lighting with high color rendering index (CRI >90Ra), making it ideal for various applications such as room decoration, TV backlighting, and night lighting.

Main product components: COB LED strip, V1 LED Dimmer, R11 RF Remote Control, and LED Power Supply.
Figure 1: Main product components of the COB LED Light Strip kit.

2. Specifications

2.1 V1 Single Color LED Controller (LED Dimmer)

V1 LED Controller with technical parameters and dimensions.
Figure 2: V1 LED Controller with technical parameters and dimensions.
ParameterValue
Input Voltage5-36VDC
Input Current8.5A
Output Voltage5-36VDC
Output Current1CH, 8A
Output Power40W (5V), 96W (12V), 192W (24V), 288W (36V)
Output TypeConstant voltage
Dimming MethodRF 2.4GHz + Push Dim
Control Distance30m (Barrier-free space)
Dimming Levels4096 (2^12)
Dimming Range0-100%
PWM Frequency2000Hz (default)
Operation Temperature-30°C to +55°C
Case Temperature (Max.)Tc+85°C
IP RatingIP20
CertificationsCE, RoHS, FCC, UL, GS, CCC
Dimensions (L×W×H)97mm × 33mm × 18mm
Gross Weight0.052kg

2.2 COB LED Light Strip

ParameterValue
Input Voltage24V
Wattage8-10W/M
FPCB Width8mm
Waterproof LevelIP20 Non-waterproof
Color TemperatureWarm White (3000-3200K), White (6000-6500K)
CRI>90Ra
Operation Temperature-20℃ to +45℃
Storage Temperature-20℃ to +60℃
View Angle120°
LengthOne roll 10M (cuttable)
LEDs Number/M320led/m

3. Package Contents

Depending on the kit purchased, your package may include:

  • COB LED Light Strip (5M, 10M, or 20M roll)
  • V1 Single Color LED Controller (Dimmer)
  • R11 RF Wireless Remote Control
  • LED Power Supply (appropriate wattage for the strip length)
Components of a 5M LED strip kit.
Figure 3: Example of kit components for a 5M LED strip.

4. Safety Precautions

  • The products shall not be stacked. Maintain a distance of ≥ 20cm to ensure proper heat dissipation and prevent damage.
  • Do not install the product close to a switching power supply. Maintain an interval of ≥ 20cm to avoid radiation interference.
  • The installation height should be ≥ 1m from the floor to avoid shortening the remote control distance due to weak reception signals.
  • Avoid placing the products near or covering them with metal objects. Maintain an interval of ≥ 20cm to avoid signal attenuation and shortened remote distance.
  • Avoid installation at wall corners or beam corners, maintaining an interval of ≥ 20cm to avoid signal interference.

5. Installation

5.1 Wire Preparation

  1. The wiring can be solid or stranded with a cross-sectional area of 0.5 to 2.5 mm². Conventional 1mm² can withstand 10A output current.
  2. When wiring is installed, the terminals must be tightened. If they are not tightened, the contact point resistance will be too high, and the terminals will easily burn due to heat when used at full load for a long time.

Note: The output power of a constant voltage power supply should be at least 1.2 times that of the output load (light strip), otherwise the full power output of the load can easily cause automatic flickering or shaking of the light.

5.2 Wiring Diagram

Wiring diagram for a single color LED strip with V1 controller and power supply.
Figure 4: Wiring diagram for connecting the single color LED strip to the V1 controller and power supply. An optional push switch can also be integrated.
Input and output connector labeling for the LED power supply.
Figure 5: LED Power Supply connector labeling (N: Zero Line, L: Livewire, Earth, V+: Output Positive, V-: Output Negative) and dimensions for 60W, 100W, and 200W units.

6. Setup & Pairing

The V1 LED Dimmer can be paired with the R11 RF Wireless Remote Control using two methods: Key Pairing or Power-on Pairing.

6.1 Key Pairing

  1. Briefly press the 'Match' button on the V1 LED Dimmer.
  2. Immediately press the power button on the R11 remote control briefly.
  3. The indicator light on the V1 dimmer will flash rapidly, indicating successful pairing.

6.2 Power-on Pairing

  1. Power off the V1 LED Dimmer, then power it on. Repeat this cycle (power off, then power on) once more.
  2. Immediately press the power button on the R11 remote control 3 times quickly.
  3. The light will flash three times to indicate successful pairing.
R11 Remote Control with LED indicator, On/Off button, and bright touch slide for dimming.
Figure 6: R11 Remote Control description, showing LED indicator, On/Off button, and touch slide for brightness adjustment (1% to 100%).

Video 1: Demonstration of V1+R11 pairing, dimming, deletion, gradient settings, and factory reset.

7. Operating Instructions

7.1 Remote Control Functions

  • On/Off: Press the power button on the R11 remote control to turn the light strip on or off.
  • Brightness Adjustment: Use the touch bar on the R11 remote control to adjust the brightness from 1% to 100%.
Brightness adjustment from 20% to 100% in a bedroom setting.
Figure 7: Visual demonstration of 10-100% adjustable brightness in a room.

7.2 Push Dim Function

The V1 LED Dimmer includes a Push-Dim interface for simple dimming using a non-latching (momentary) wall switch:

  • Short press: Turn the light on or off.
  • Long press (1-6s): Press and hold for stepless dimming. With every other long press, the light level will change in the opposite direction (dimming up or down).
  • Dimming memory: The light returns to the previous dimming level when switched off and on again, even after a power failure.
  • Synchronization: If multiple controllers are connected to the same push switch, a long press for more than 10 seconds will synchronize the system, and all lights in the group will dim up to 100%. This eliminates the need for additional synchrony wiring in larger installations. It is recommended that the number of controllers connected to a single push switch does not exceed 25 pieces. The maximum length of wires from the push switch to the controller should not exceed 20 meters.
Diagram showing compatibility of V1 LED Dimmer with various RF wireless LED controllers, including dimming remotes, panel controls, and Wi-Fi relays.
Figure 8: RF Wireless LED Controllers Compatibility, illustrating how V1 dimmers can be controlled by various remotes and synchronized.

8. Gradient Settings (Light On/Off Fade Time)

You can adjust the light on/off fade time:

  • Set 3-second fade: Hold the 'Match' button on the V1 LED Dimmer for 5 seconds, then briefly press the 'Match' button 3 times. The indicator light will flash three times, confirming the 3-second switch fade setting.
  • Restore default (0.5-second fade): Hold the 'Match' button on the V1 LED Dimmer for 10 seconds. This will restore the factory default parameter, setting the light on/off fade time back to 0.5 seconds.

9. Factory Settings

To restore the V1 LED Dimmer to factory default settings, hold the 'Match' button on the dimmer for 10 seconds. The indicator light will flash to confirm the reset.

10. Malfunctions Analysis & Troubleshooting

Dimming curve graph and troubleshooting table for common malfunctions.
Figure 9: Dimming curve (PWM duty vs. brightness) and a table outlining common malfunctions, their causes, and troubleshooting steps.
MalfunctionCausesTroubleshooting
No light1. No power.
2. Wrong connection or insecure.
1. Check the power.
2. Check the connection.
Uneven intensity between front and rear, with voltage drop1. Output cable is too long.
2. Wire diameter is too small.
3. Overload beyond power supply capability.
4. Overload beyond controller capability.
1. Reduce cable or loop supply.
2. Change wider wire.
3. Replace higher power supply.
4. Add power repeater.
No response from the remote1. The battery has no power.
2. Beyond controllable distance.
3. The controller did not match the remote.
1. Replace battery.
2. Reduce remote distance.
3. Rematch the remote.

11. User Tips

  • For longer LED strip runs or multiple strips, ensure your power supply is adequately rated (at least 1.2 times the total wattage of the LED strips). Consider using power repeaters to maintain consistent brightness and prevent voltage drop, especially if you experience uneven lighting or flickering.
  • Always double-check all wiring connections to ensure they are secure and correct to prevent issues like lights not turning on or overheating.

12. Maintenance

  • Keep the LED strip and controller clean and free from dust. Use a soft, dry cloth for cleaning.
  • Avoid exposing the components to excessive moisture or extreme temperatures.
  • Regularly check wiring connections for any signs of wear or looseness.
  • If the remote control's performance degrades, replace its battery.

13. Warranty & Support

The V1 LED Dimmer controller comes with a 5-year warranty. For detailed item guides and documents, please refer to the official user manual PDF available at: User manual (PDF).

For further assistance or technical support, please contact your retailer or the manufacturer.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.