1. Introduction and Product Overview
The PowMr LiFePo4 50AH 12V Battery Pack (Model: POW-50AH-12.8V) is a high-performance, rechargeable lithium iron phosphate battery designed for a wide range of energy storage applications. It serves as an ideal upgrade replacement for traditional lead-acid battery packs, offering superior energy density, efficiency, and a long cycle life.
This battery series is engineered for reliability and safety, featuring a built-in Battery Management System (BMS) that provides comprehensive protection. Its robust design makes it suitable for various environments and uses, from residential and commercial energy storage to mobile and marine applications.
Key features include:
- Nominal Capacity: 50AH
- Nominal Voltage: 12.8V
- Nominal Energy: 640WH
- Built-in BMS: 100A BMS for comprehensive protection
- Long Cycle Life: Exceeds 4000 cycles at 0.2C discharge, 25°C, and 80% DOD
- High Capacity and Endurance: Supports up to 640W continuous load power
- Efficient Charging: Maximum charging current of 50A, allowing full charge in as little as one hour
- Flexible Configuration: Can be configured up to 4 in series and 4 in parallel, achieving a total capacity of up to 200Ah, a total voltage of up to 51.2V, and a total energy of up to 10240Wh.
2. Safety Information and Precautions
⚠️ WARNING: Please read and understand all safety instructions before installation, operation, or maintenance of the battery. Failure to follow these instructions may result in electric shock, fire, severe injury, or death.
- Fire Risk: Please mind potential fire risk and strictly follow the instruction manual for charging and storage.
- Disposal: For disposal, please check your local authority's website for more information and dispose of the lithium-ion battery safely in accordance with the applicable legal requirements.
- No Short Circuit: Do not short circuit the battery terminals.
- No Water Exposure: Do not expose the battery to water.
- Read Manual: Always refer to the latest version of the technical manual published on our website to ensure safe and efficient operation.
- Manufacturer Responsibility: The company assumes no responsibility for any accidents caused by not following this user manual.
3. Product Specifications
General Specifications
| Attribute | Value |
|---|---|
| Brand Name | PowMr |
| Model Number | POW-50AH-12.8V |
| Type | LiFePO4 |
| Nominal Capacity | 50AH |
| Voltage | 12V |
| Rated Voltage | 12V |
| Energy Density | 640Wh |
| Weight | 5.8KG (Net) / 6.0KG (Package) |
| Dimensions (LxWxH) | 26*17*24CM (Product) / 228x138x226mm (Battery) |
| Connection | Others (M8 Terminal Bolts) |
| High-concerned chemical | None |
| Origin | Mainland China |
| Certification | CE |
| Applications | Air Conditioner, RV, Marine Boat, Trolling Motor, Home Energy, Solar Power Storage |
Battery Performance Specifications
| Parameter | Value |
|---|---|
| Battery Type-Chemistry | LiFePO4 |
| Nominal Voltage | 12.8V |
| Nominal Capacity | 50Ah |
| Energy Density | 640Wh |
| Weight | 6kg |
| Terminal Type | M6 |
| Terminal Torque | 8.5Nm |
| Case Material | ABS |
| BMS Built-in | Yes |
| Self-Discharging Per Month | <3% |
| Max in Parallel | 4 |
| Max in Series | 4 |
| Charging Voltage Range | 10.8~14.4V |
| Recommend Charge Voltage | 14V |
| Max Charge Voltage | 14.4V |
| Max Continuous Current | 50A |
| Recommend Discharge Voltage | 11.2V |
| Max Discharge Voltage | 10.8V |
| Max Continuous Discharge Current | 50A |
| Cycle Life (0.2C, 25°C@80% DOD) | 4000 Cycle |
| Discharge Temperature | -10~60℃ |
| Charge Temperature | 0~60°C |
| Storage Temperature | -30~50°C |
4. Setup and Installation
4.1 Unpacking and Initial Inspection
Upon receiving your battery pack, carefully unpack it and inspect for any visible damage. Verify that all components are present. It is recommended to check the initial voltage of the battery upon arrival.
4.2 Terminal Connection
The battery uses M6 terminal bolts. Ensure connections are secure to prevent arcing and ensure optimal performance. The recommended terminal torque is 8.5Nm.
4.3 Series and Parallel Configuration
The PowMr LiFePo4 battery pack can be configured for increased voltage (series) or increased capacity (parallel) up to a maximum of 4 units in series and 4 units in parallel. This allows for a total capacity of up to 200Ah, a total voltage of up to 51.2V, and a total energy of up to 10240Wh.
- Parallel Connections: For parallel connections, fully discharge all batteries to the same voltage before connecting them in parallel. After connecting, recharge them together. Parallel connections are intended only to extend backup time, not to increase output power.
- Series Connections: For series connections, ensure the remaining capacity (State of Charge) of each battery is the same before connecting.
5. Operating Instructions
5.1 Charging
- Recommended Charge Voltage: 14V
- Max Charge Voltage: 14.4V
- Max Continuous Current: 50A
- Charge Temperature: 0~60°C
- The battery can achieve a full charge in as little as one hour with a maximum charging current of 50A.
5.2 Discharging
- Recommended Discharge Voltage: 11.2V
- Max Discharge Voltage: 10.8V
- Max Continuous Discharge Current: 50A
- Discharge Temperature: -10~60°C
- The battery supports up to 640W continuous load power, capable of powering multiple loads simultaneously.
5.3 Applications
This battery is versatile and can be used for:
- Emergency Power
- On-board Power (e.g., RVs, Marine Boats)
- Outdoor Use (e.g., camping)
- Home Energy Storage
- Solar Power Storage Systems
- Trolling Motors
- Air Conditioners
6. Maintenance
- Storage Temperature: For optimal longevity, store the battery within the recommended temperature range of -30~50°C.
- Self-Discharge: The battery has a low self-discharge rate of less than 3% per month. For long-term storage, it is advisable to store the battery at approximately 50% State of Charge (SOC).
- Regular Inspection: Periodically check the battery terminals for corrosion or loose connections. Clean as necessary and ensure terminals are tightened to 8.5Nm.
- Avoid Deep Discharge: While the battery is protected by BMS, avoiding frequent deep discharges can extend its overall lifespan.
7. Troubleshooting
The PowMr LiFePo4 battery pack is equipped with a comprehensive Battery Management System (BMS) that provides multiple layers of protection. If the battery is not functioning as expected, the BMS may have activated a protection feature.
7.1 BMS Protection Features
| Protection Type | Trigger Condition | Delay Time |
|---|---|---|
| Primary Charging Protection | Current: 60A | 1-1.5s |
| Second Charging Protection | Current: 90A | 0.5-1s |
| Primary Discharging Protection | Current: 100A | 400ms |
| Second Discharging Protection | Current: 120A | 40ms |
| Over Charge Voltage Protection | Voltage: 14.4V | 0.5-1.5s |
| Over Discharge Voltage Protection | Voltage: 8.4V | 0.5-1.5s |
| Temperature Protection (PCB) | PCB Temperature ≥98°C | N/A |
| Temperature Recovery | Recover Temperature ≤80°C | N/A |
If the battery stops providing power or accepting a charge, check if any of these conditions have been met. The BMS will typically reset once the condition is no longer present. If issues persist, contact customer support.
8. Performance Curves
The following graphs illustrate the performance characteristics of the PowMr LiFePo4 battery pack under various conditions.
8.1 Constant Current Discharge Data (Amperes@25°C, Cut off voltage 10.8V)
| Discharging Time | 1h | 2h | 3h | 4h | 5h | 10h | 20h |
|---|---|---|---|---|---|---|---|
| Discharging Current | 50A | 25A | 16.6A | 12.5A | 10A | 5A | 2.5A |
8.2 Constant Current Discharge Data (Watts@25°C, Cut off voltage 10.8V)
| Discharging Time | 1h | 2h | 3h | 4h | 5h | 10h | 20h |
|---|---|---|---|---|---|---|---|
| Discharging Power | 640W | 320W | 213.3W | 160W | 128W | 64W | 32W |
8.3 Performance Curves Visualizations
9. User Tips
- Initial Voltage Check: Upon receiving your battery, it's a good practice to check its initial voltage. Users have reported receiving units with a healthy initial voltage (e.g., 13.3V), indicating readiness for use.
- Parallel Connection Preparation: When connecting batteries in parallel, ensure all units are fully discharged to the same voltage before making connections. This helps balance the batteries and prevents potential issues.
- Series Connection Preparation: For series connections, verify that the State of Charge (SOC) is identical across all batteries to be connected.
10. Warranty and Support
For detailed warranty information and support, please refer to the official PowMr website or the comprehensive user manual PDF. The PDF manual contains additional diagrams and in-depth instructions that may not be fully covered here.
You can access the full user manual (PDF) here.
11. Contact Information
Manufacturer: SHENZHEN HEHEJIN INDUSTRIAL CO.,LTD
- Website: www.powmr.com
- E-mail: support@powmr.com
- Tel/Fax: +86 755-28219903
- Address: Henggang Street, Longgang District, Shenzhen, Guangdong, China