1. Introduction
This manual provides detailed instructions for the Diymore Mini DC-DC Step-Down Converter module, model A0004. This compact module efficiently converts higher DC voltages (5-16V) to stable lower voltages (3.3V or 5V), making it ideal for various electronic projects requiring precise power regulation.

The module is designed for efficient voltage conversion from 5-16V input to selectable 3.3V or 5V output.
2. Setup Instructions
Follow these steps to correctly set up your DC-DC step-down converter module:
- Identify Connections: The module has clearly labeled pads for input and output:
- VIN: Voltage Input (DC 4.6-16V)
- GND: Ground (common for input and output)
- OUT: Voltage Output (3.3V or 5V)
- Select Output Voltage: The module allows you to select between 3.3V and 5V output. This is typically done by bridging specific pads (A or B) on the module. Refer to the module's silkscreen for exact configuration.
- To select 3.3V output, ensure the appropriate pad (e.g., '3V3' or 'B') is configured.
- To select 5V output, ensure the appropriate pad (e.g., '5V' or 'A') is configured.
- Connect Input Power: Connect your DC power source (4.6V to 16V) to the VIN and GND input pads. Ensure correct polarity.
- Connect Load: Connect your device or circuit requiring 3.3V or 5V to the OUT and GND output pads.
- Mounting: The module features a ring terminal design, making it suitable for direct surface mounting onto your own PCBs or for wire bonding.

This diagram highlights key components like TVS protection, tantalum capacitors, the TPS565201 chip, and indicates the double-sided board design suitable for SMD or wire bonding.

View of the module showing the configuration for 3.3V output.

View of the module showing the configuration for 5V output.
3. Operating Instructions
Once properly connected, the module operates automatically to provide the selected stable output voltage.
- Input Voltage Range: The module accepts a DC input voltage between 4.6V and 16V.
- Output Current: It delivers a peak current of 5A and a sustained high-current output of 3.8A.
- Thermal Performance: At an ambient temperature of approximately 25°C, with a 12V input and 5V/3.8A output, the chip temperature typically reaches around 100°C. The chip maintains stable operation even at 120°C. For continuous operation at maximum current (5A), especially in enclosed spaces, consider adding a heat sink to ensure optimal performance and longevity.
- Hot-Swapping: This module has been optimized for reliability and includes dedicated testing for hot-swapping at 16V, minimizing the risk of damage during power connection changes.

The module provides 3.3V/5V output options to meet the power needs of various devices with up to 5A output.
4. Maintenance
The Diymore Mini DC-DC Step-Down Converter module is designed for reliable, long-term operation with minimal maintenance.
- General Care: Keep the module in a dry environment and protect it from dust, moisture, and extreme temperatures.
- Cleaning: If necessary, gently clean the module with a soft, dry brush. Avoid using liquids or abrasive cleaners.
- Physical Damage: Avoid dropping or subjecting the module to physical shock, which can damage internal components.
- No User-Serviceable Parts: There are no user-serviceable parts inside the module. Do not attempt to disassemble or repair it.
5. Troubleshooting
If you encounter issues with your module, consider the following troubleshooting steps:
- No Output Voltage:
- Check that the input voltage (VIN) is within the specified range (DC 4.6-16V).
- Verify all connections (VIN, GND, OUT) are secure and correctly polarized.
- Ensure the output voltage selection (3.3V/5V) is correctly configured.
- Unstable Output Voltage:
- Check the quality of your input power supply; ensure it is stable and can provide sufficient current.
- Verify that the load connected to the output does not exceed the module's maximum current rating (5A peak, 3.8A sustained).
- Inspect all solder joints and connections for any loose or poor contacts.
- Module Overheating:
- Ensure the load current does not exceed the module's specifications.
- Provide adequate ventilation around the module.
- For continuous high-current operation (e.g., 5A), consider attaching a small heat sink to the main chip to improve thermal dissipation.
6. Specifications
Detailed technical specifications for the Diymore Mini DC-DC Step-Down Converter A0004:
| Parameter | Value |
|---|---|
| Input Voltage | DC 4.6V - 16V |
| Output Voltage | 3.3V / 5V (Selectable) |
| Output Current | 5A (Peak), 3.8A (Sustained) |
| Switching Frequency | 580kHz |
| Converter Chip | TPS565201 |
| Protection | Built-in TVS (Surge and Anti-static) |
| Dimensions (L x W) | 24mm x 15mm (0.94in x 0.59in) |
| Features | Ring connector for SMD/wire bonding, Double-sided board, Tantalum capacitors |

Summary of key electrical specifications.

The module measures 24mm in length and 15mm in width.

The module utilizes the TPS565201 chip for high conversion efficiency and low temperature rise.

Built-in TVS protection provides surge and anti-static protection, enhancing system reliability.
7. User Tips
Here are some friendly tips for getting the most out of your Diymore DC-DC converter module:
- Common Application: This module is primarily used to interface 12V power systems with 5V and 3.3V power systems, providing a reliable power bridge.
- Sustained Current: While capable of a 5A peak, the module is designed for a long-term sustained output current of 3.8A. Plan your projects accordingly.
- Thermal Management: For applications requiring continuous 5A output or operating in high ambient temperatures, attaching a heat sink is highly recommended. Tests show that with a heat sink, the module can deliver 5V at 5A (25W) for over 30 minutes without issues.
- Reliability: The design includes separate 16V hot-swap testing, ensuring enhanced reliability compared to many modules that may be susceptible to damage during hot-swapping.
8. Warranty and Support
For any technical assistance, warranty claims, or support inquiries regarding your Diymore Mini DC-DC Step-Down Converter A0004, please contact the seller or manufacturer directly through your purchase platform. Please provide your order details and a clear description of the issue to facilitate prompt support.
9. Product Video
Watch the official product video for a visual overview of the Diymore Mini DC-DC Step-Down Converter module.
Product showcase video of the Diymore Mini DC-DC Step-Down Converter module.