1. Introduction
The Rakoncnc 6090 Mini CNC Wood Router is a versatile machine designed for engraving and carving various materials, including wood, MDF, PVC, metal, and aluminum. This manual will guide you through the safe operation, setup, maintenance, and troubleshooting of your machine to ensure optimal performance and longevity.
The machine is delivered securely packaged in a wooden crate, as shown below, to ensure its protection during transit.
Figure 1: Rakoncnc 6090 Mini CNC Wood Router in shipping crate.
2. Safety Precautions
2.1 Hazard: Mechanical Injury
- Never touch the cutting tool with your hands while the spindle is rotating.
- No part of your body may enter the work area while the machine is running.
- Protective covers or safety light curtains must be installed and must not be removed.
- Long hair must be tied up. Never wear gloves while operating rotating equipment.
2.2 Warning: Fire Risk
- Wood chips and dust are flammable. Smoking is strictly prohibited in the work area.
- Fire extinguishers must be available (carbon dioxide or dry powder recommended).
- Clean the dust collection box daily. Do not leave it overnight.
- Do not leave the machine while the spindle is cutting at high speed.
2.3 Note: Other Hazards
- Equipment must be reliably grounded.
- The spindle and drive are high-voltage components. Unauthorized personnel must not open the electrical control box.
- The dust collection hose must not be entangled in moving parts.
- Workpieces must be reliably fixed. Processing without securing the workpiece is strictly prohibited.
3. Equipment Components
The Rakoncnc 6090 Mini CNC Wood Router consists of the following main components:
- Bed: Cast iron/steel gantry frame for stability.
- Spindle: Air-cooled or water-cooled spindle motor (3.2kw water cooling spindle for RCM1212 model).
- Control System: Handle or Computer control card + driver (e.g., Nc studio controller, parallel interface).
- Transmission System: Lead screw/rack + guide rail (Rack and pinion on X,Y axis, Z axis ball screw transmission).
- Accessories: Cutting tools, tool setter, clamping fixture, dust hood.
Figure 2: Key components of the CNC Router.
4. Setup and Preparation
4.1 Startup Procedure
- Confirm emergency stop button is pressed.
- Turn on main power switch.
- Release emergency stop button.
- Turn on control computer/handheld.
- Open control software.
- Reset alarm (if any).
- Start spindle cooling system (water chiller).
- Start vacuum cleaner.
- Startup complete.
4.2 Workpiece Clamping Fixing Principles
- Sheet metal must be clamped on all four sides or using vacuum-adhesive.
- Temporary fixing with nails or double-sided tape is strictly prohibited.
- Lightweight, thin sheets must be protected from vibration during cutting.
4.3 Tool Installation
- Clean the tool holder and spindle collet (free of oil and wood chips).
- Tool Extension Length: Just penetrate the workpiece + 3~5mm; excessive extension may break the tool.
- Tighten the Locking Nut: Apply force with a wrench until locked; never start the machine without tightening.
- Manually rotate the spindle to check for tool eccentricity and whether it is hitting the workpiece.
4.4 Tool Setting (Setting the Workpiece Zero Point)
Recommended Method: Automatic Tool Setter
- Place the tool setting block on the workpiece surface.
- Execute the "Automatic Tool Setting" command in the control software.
- The system automatically records the Z-axis zero point.
Manual Tool Setting:
- X/Y Zero Point: Align the tool tip with the lower left edge of the workpiece.
- Z Zero Point: Using a feeler gauge/tool setting block, lift the tool 0.1~0.2mm after it contacts the surface.
- Zeroing: Set the current position as the workpiece coordinate in the software.
5. Operating Instructions
5.1 Control System Interface (e.g., Weihong/Baoyuan/Xindai)
- Manual Mode: X/Y/Z axis jogging, spindle start/stop.
- Automatic Mode: Load G-code, start machining.
- Parameter Settings: Machining speed, spindle speed, origin setting.
5.2 Program Loading
- Generate toolpaths using software such as ArtCAM / AlphaCAM / Jingdiao / Wentai.
- Post-process to machine tool recognition formats (.nc/.cnc/.u00/.tap, etc.).
- Transfer to the controller via USB flash drive/network.
- Dry Run Verification: Raise the Z-axis by 30mm, simulate operation, and confirm no collisions.
5.3 Start Machining
- Close the safety door.
- Reconfirm the vacuum is on.
- Press "Cycle Start".
- Pay close attention to the first cut: Observe the cutting sound and whether chip removal is normal.
- If any abnormal noise, smoke, or displacement occurs, immediately press emergency stop.
Video 1: Demonstration of the CNC router carving an intricate design of a dragon and phoenix on a wooden surface.
6. Maintenance
6.1 Shutdown Procedure
- Stop the machining program.
- Raise the tool to a safe height.
- Shut down the spindle.
- Exit the control software.
- Turn off the computer/handheld.
- Press the emergency stop button.
- Turn off the main power switch.
- Clean the worktable and dust collection box.
- Apply guide rail oil.
6.2 Weekly Maintenance
- Clean rack and pinion; apply lithium grease.
- Check spindle cooling system (water level/air filter).
- Inspect all bolts and fasteners for looseness.
- Test all axis movements for abnormal noise.
- Clean dust collector filter.
6.3 Monthly Maintenance
- Replace cooling water (water-cooled spindle).
- Clean or replace spindle air filter (air-cooled).
- Check drive belt tension.
- Inspect electrical cabinet cooling fan.
- Verify machine leveling.
6.4 Quarterly Maintenance
- Deep clean electrical cabinet with dry compressed air (power off).
- Check all limit switches and sensors.
- Inspect ball screw nuts for backlash.
- Test ground continuity.
- Professional inspection of spindle bearings.
7. Troubleshooting
7.1 Common Errors and Solutions
- Forgetting to Lift the Tool: Starting machining directly after tool setting can lead to tool collision. Always ensure the tool is lifted to a safe height before starting.
- Forgetting Material Thickness Difference: Not accounting for shim height can cause the tool to cut through the worktable. Always verify material thickness and adjust Z-axis settings accordingly.
- Abnormal Noise, Smoke, or Displacement: If any of these occur during machining, immediately press the emergency stop button. Investigate the cause before resuming operation.
8. Specifications
The following table outlines the key specifications for the Rakoncnc RCM1212 model (specifications may vary slightly for other models like RCM6090):
| Attribute | Value |
|---|---|
| Model | RCM6090 (RCM1212 shown in table) |
| Working Area | 600x900mm (RCM1212: 1200×1200×200mm) |
| Spindle Motor | 3.2kw water cooling spindle |
| Working Mode | Stepper motor (servo is optional) |
| Control System | Nc studio controller, parallel interface |
| Drive Mechanism | Rack and pinion on X,Y axis, Z axis ball screw transmission |
| Table Surface | T-slot table (vacuum table optional) |
| Frame | Seamless welded steel structure |
| Motion Positioning Accuracy | ± 0.03/300mm |
| Repositioning Accuracy | ± 0.05mm |
| Max Motion Speed | 30,000mm/min |
| Max Engraving Speed | 25,000mm/min |
| Rotating Speed of Spindle | 24,000rpm |
| Z-axis setting | Auto Z origin tool sensor |
| Dictate Format | G code, *.u00, *.mmg, *.plt |
| Operating Voltage | 220V/ 380V |
| Software | Type3, ArtCAM software |
| Packing Size | 3100*2250*1850mm |
| Lubrication System | Oil lubrication system |
| Gross Weight | 350kg |
9. User Tips
- Always confirm the machine's cutting depth capabilities against your material's thickness. For example, if you intend to cut natural wood of 5 cm thickness, ensure your specific machine configuration supports this depth.
- For complex projects or specific material requirements, consult the detailed specifications and consider contacting support for tailored advice.
- Regularly check for software updates for your control system (e.g., Nc studio, MACH3) and CAM software (e.g., ArtCAM, Type3) to ensure compatibility and access to new features.
10. Warranty and Support
The machine and spindle come with a 1-year warranty. For technical support, detailed instructions, or operation videos, please contact us at: info@honorfuturecnc.com.
Our qualified mechanical engineers are available to provide free technical advice.
11. Prohibited Operations
To ensure safety and prevent damage to the machine, the following operations are strictly prohibited:
- NEVER change tools while the spindle is rotating.
- NEVER reach into the work area during machine operation.
- NEVER wear gloves while operating.
- NEVER run the machine with safety guards removed.
- NEVER start a water-cooled spindle without coolant.
- NEVER machine unsecured workpieces.
- NEVER use compressed air to blow down the machine table (this creates a dust hazard).
- NEVER leave the machine unattended overnight (essential woodworking rule).
- NEVER modify system parameters without authorization.
12. Machine Applications
The Rakoncnc 6090 Mini CNC Wood Router is suitable for a wide range of applications and materials:
12.1 Suitable Materials
- Acrylic sheet
- ABS double color sheet
- PVC foam sheet
- Wooden sheet
- PCB
- Aluminum
- Brass
- Steel
- And other similar materials.
12.2 Application Areas
- Wood Furniture Industry: Wave plates, fine patterns, antique furniture, wooden doors, screens, craft sashes, composite gates, cupboard doors, interior doors, sofa legs, headboards, game cabinets, computer tables, sewing machine tables, instruments, etc.
- Advertising Industry: Advertising identification, sign making, Acrylic engraving and cutting, crystal word making, blaster molding, and other advertising material derivatives making.
- Crafts: Engraving characters of any language and patterns on gifts and souvenirs, primitive processing and shaping of artistic crafts, and stiletto.
- Moulding: Engraving delicate letter and flower patterns, primitive and fine processing of small molds.
- Architectural Models: Engraving fine window, fencing, and wall patterns, etc.
Figure 3: Furniture industry applications.
Figure 4: Diverse material processing examples.
Figure 5: Additional application examples.
13. Additional Resources
A detailed user manual in PDF format is available for download. This document provides more in-depth information on specific operations and advanced features.
User Manual (PDF): For a comprehensive guide, please refer to the official PDF manual: Download User Manual (PDF)