1. Introduction
This manual provides instructions for the proper installation, operation, and maintenance of your new gas spring lift supports for the engine bonnet of your Audi A8 D3. These components are designed to assist in lifting and securely holding the bonnet open, ensuring safe access to the engine compartment. Please read this manual thoroughly before proceeding with installation or use.
2. Specifications
| Feature | Detail |
|---|---|
| Product Name | Gas Spring Engine Bonnet Lift Support |
| Fitting Position | Front Bonnet (Left and Right) |
| Quantity | 2 pieces |
| Reference Part Numbers | 4E0823359C, 4E0823359D |
| Force Rating | 280N |
| Extended Length | Approximately 39.5 cm |
| Package Weight | 0.6 kg |
| Package Dimensions | 40 cm (L) x 5 cm (W) x 5 cm (H) |
Note: Specifications are approximate and may vary slightly.
3. Vehicle Compatibility
These gas spring lift supports are compatible with the following Audi A8 D3 models manufactured between October 2002 and December 2010:
- AUDI A8 D3 (4E2, 4E8) 2.8 FSI (BDX) 2773cc, 154kW, 6 Saloon (2007-2010)
- AUDI A8 D3 (4E2, 4E8) 3.0 (ASN) 2976cc, 162kW, 6 Saloon (2003-2005)
- AUDI A8 D3 (4E2, 4E8) 3.0 (BBJ) 2976cc, 160kW, 6 Saloon (2003-2006)
- AUDI A8 D3 (4E2, 4E8) 3.0 Long quattro (ASN) 2976cc, 160kW, 6 Saloon (2003-2004)
- AUDI A8 D3 (4E2, 4E8) 3.0 TDI quattro (ASB) 2967cc, 171kW, 6 Saloon (2003-2010)
- AUDI A8 D3 (4E2, 4E8) 3.0 TDI quattro (BNG) 2967cc, 155kW, 6 Saloon (2003-2010)
- AUDI A8 D3 (4E2, 4E8) 3.2 FSI (BPK) 3123cc, 191kW, 6 Saloon (2005-2010)
- AUDI A8 D3 (4E2, 4E8) 3.2 FSI quattro (BPK) 3123cc, 191kW, 6 Saloon (2005-2010)
- AUDI A8 D3 (4E2, 4E8) 3.7 quattro (BFL) 3697cc, 206kW, 8 Saloon (2002-2006)
- AUDI A8 D3 (4E2, 4E8) 4.0 TDI quattro (ASE) 3936cc, 202kW, 8 Saloon (2003-2005)
- AUDI A8 D3 (4E2, 4E8) 4.2 FSI quattro (BVJ) 4163cc, 257kW, 8 Saloon (2006-2010)
- AUDI A8 D3 (4E2, 4E8) 4.2 quattro (BFM) 4172cc, 246kW, 8 Saloon (2002-2010)
- AUDI A8 D3 (4E2, 4E8) 4.2 TDI quattro (BMC) 4134cc, 235kW, 8 Saloon (2005-2007)
- AUDI A8 D3 (4E2, 4E8) 4.2 TDI quattro (BVN) 4134cc, 240kW, 8 Saloon (2007-2009)
- AUDI A8 D3 (4E2, 4E8) 6.0 W12 quattro (BHT) 5998cc, 331kW, 12 Saloon (2003-2010)
- AUDI A8 D3 (4E2, 4E8) S8 quattro (BSM) 5204cc, 331kW, 10 Saloon (2006-2010)
4. Package Contents
Your package should contain:
- 2 x Gas Spring Engine Bonnet Lift Supports
Inspect all components for any signs of damage upon receipt. If any parts are missing or damaged, please contact customer support immediately.
5. Safety Information
WARNING:
- Gas springs contain high-pressure gas. Do not heat, puncture, or open the gas spring.
- Do not attempt to repair damaged gas springs.
- Proper disposal is required. Follow local regulations for disposing of gas-filled components.
- Always wear appropriate personal protective equipment (PPE), such as safety glasses and gloves, during installation.
- Ensure the bonnet is securely supported before removing old gas springs to prevent accidental closure and injury.
6. Installation Instructions
Installation of gas springs typically involves a few simple steps, but professional installation is recommended if you are not familiar with automotive repairs. Refer to the diagram below for general mounting points.
- Prepare the Vehicle: Park the vehicle on a level surface and ensure the engine is off and cool.
- Secure the Bonnet: Have a helper securely hold the bonnet open, or use a sturdy prop rod to prevent it from falling unexpectedly.
- Remove Old Gas Springs:
- Locate the attachment points of the old gas spring. These are typically ball joints.
- Using a small flat-head screwdriver or a specialized tool, carefully pry open the retaining clips on both ends of the old gas spring.
- Once the clips are disengaged, gently pull the gas spring off the ball studs.
- Install New Gas Springs:
- Align one end of the new gas spring with its corresponding ball stud. Push firmly until it snaps into place. You may hear a click.
- Repeat for the other end of the gas spring. Ensure both ends are securely attached.
- Repeat the process for the second gas spring on the other side of the bonnet.
- Test Operation: Carefully remove the prop rod (if used) and slowly lower and raise the bonnet to ensure the new gas springs function correctly and hold the bonnet securely in the open position.
7. Operating Instructions
Once installed, the gas springs will assist in lifting the engine bonnet and holding it in the fully open position. To open the bonnet, release the primary and secondary latches as per your vehicle's owner's manual. The gas springs will then smoothly lift the bonnet. To close, gently pull the bonnet down until the latches engage. Do not force the bonnet down, as this can damage the springs or hinges.
8. Maintenance
Gas springs are generally maintenance-free. However, regular inspection is recommended:
- Visual Inspection: Periodically check the gas springs for any signs of damage, corrosion, leaks, or bent rods.
- Attachment Points: Ensure the attachment points (ball joints and clips) are secure and free from excessive wear.
- Cleanliness: Keep the gas springs clean and free from dirt, grime, or debris, especially around the rod and seals.
- Functionality: If the bonnet does not stay open reliably or is difficult to open/close, the gas springs may need replacement.
9. Troubleshooting
- Bonnet does not stay open: This typically indicates that the gas springs have lost pressure and need to be replaced.
- Bonnet is difficult to close: This could mean the gas springs are too strong for the application (unlikely if correct part number is used) or are binding. Check for proper alignment and ensure no obstructions.
- Unusual noises (squeaking, grinding): Inspect attachment points for wear or lack of lubrication. A small amount of silicone grease can be applied to the ball joints if needed.
10. User Tips
To ensure you purchase and install the correct parts for your vehicle:
- Always verify the goods description carefully against your vehicle's specifications.
- If you are uncertain about compatibility, provide all known information about your car, such as the part number of the old component, the car's VIN (Vehicle Identification Number), and clear photos of the used part, to your supplier for confirmation.
11. Warranty and Support
For any questions regarding product functionality, installation, or potential defects, please contact the seller or manufacturer's customer support. Keep your purchase receipt as proof of purchase.
Further documentation, including a user manual in PDF format, may be available. Please refer to the product listing or contact support for access to these resources.
12. Frequently Asked Questions (FAQ)
No specific FAQs are available at this time. For common inquiries, please refer to the troubleshooting section or contact customer support.