1. Product Overview
The Voktta T459 is a professional digital battery voltage and internal resistance tester designed for high-precision measurements. It features a communication four-line method for accuracy, an encoder for efficient operation, and a high-gloss aluminum knob cap for a premium feel. The device supports Bluetooth connectivity to a dedicated mobile application, allowing for remote display, configuration, and access to historical data. It also supports OTA firmware updates for continuous improvement.
Figure 1: Voktta T459 Digital Battery Voltage Internal Resistance Tester with included cables.
2. Safety Information
- Do not test AC power. This device is designed for DC measurements only.
- Do not test voltages above 45V to prevent damage to the device and ensure user safety.
- Ensure the operating voltage does not exceed DC 5V to avoid overvoltage.
- Always ensure proper insulation when connecting the power supply and test leads to prevent short circuits or electrical hazards.
3. Package Contents
Please verify that all items are present in your package:
- Internal resistance tester (T459) x 1
- XH-2.54-3P red-black-yellow power cable (150mm long) x 1
- XH-2.54-4P signal acquisition cable (400mm long) x 1
4. Specifications
| Parameter | Value |
|---|---|
| Product Name | Digital Battery Tester |
| Brand Name | Voktta |
| DIY Supplies | Electrical |
| Operating Voltage | DC 5V (Do not supply power with overvoltage) |
| Testing Principle | AC 4-wire method |
| Voltage Test Range | 0.001V to 45.00V (Max resolution 0.001V) |
| Internal Resistance Measurement Range | 0.1mΩ to 7.999Ω (Max resolution 0.1mΩ) |
| Data Logging | Supports recording 20 sets of data (last 5 viewable on device, all via APP) |
| Voltage Display Fine-tuning | Supported |
| Internal Resistance Display Fine-tuning | Supported |
| Automatic Shutdown | Supports 1-9 minute standby time adjustment |
| Backlight Brightness | 1-9 levels of adjustment |
| Product Size | 79 × 43 × 26 mm |
| Installation Opening | 75 × 39 mm |
| Product Weight | Net weight 38g, with packaging 64g |
Figure 2: Detailed product parameters.
Figure 3: Dimensions of the T459 tester and recommended installation opening size.
5. Setup
5.1 Power Supply
The T459 tester can be powered by either a DC 5V power supply or an 18650 battery. An 18650 battery + power adapter board can also be used (purchased separately).
- DC 5V or 18650 Battery (Two-wire method): Connect the thin red wire to the positive electrode and the thin black wire to the negative pole. The yellow wire indicates charging status and should not be connected normally. Ensure proper insulation.
- 18650 Battery + Power Adapter Board: This method requires a separate power adapter board for the 18650 battery.
Figure 4: Diagrams illustrating the two power supply methods.
5.2 Test Connections
Before use, prepare a 5V power supply or an 18650 battery. Use the XH-2.54-4P signal acquisition cable to create a custom test fixture or purchase additional accessories like an XH2.54-4P Kelvin clamp or an XH2.54-4P battery test stand.
- Using Kelvin Clamp: Plug the XH2.54-4P cable into the 4P terminal on the back of the meter. Connect the Kelvin clamps to both ends of the component being tested.
- Using Battery Test Stand: For cylindrical batteries, press the negative pole of the top battery onto the active end of the test stand and the positive pole onto the fixed end.
Figure 5: Demonstration of connecting the Kelvin clamp for testing.
Figure 6: Instructions for testing using a battery test stand.
5.3 Bluetooth (BT) Connection
The T459 supports Bluetooth communication for mobile app integration.
- Open the Wuzhi Zhilian app on your phone and ensure Bluetooth is enabled.
- Click on "Add Device" in the app interface. The app will automatically search for "ZK-T459".
- Click on "ZK-T459" to connect. The connection should be automatic.
- Once successfully connected, click "finish" in the app.
- Click on the device icon in the app to enter the normal operation interface. Long press the product icon to change the device name or delete it.
Figure 7: Steps for connecting the T459 to the mobile app via Bluetooth.
6. Operating Instructions
6.1 Basic Operation
- Power On/Off: Use the ON/OFF button on the device.
- Encoder Knob: The exquisite high-gloss aluminum knob cap allows for efficient and fast operation, providing a good operating feel.
Figure 8: The encoder knob for efficient operation.
6.2 Interface Display
The device features various display interfaces:
- Main Interface 1: Shows voltage and resistance data when not measured and during measurement.
- Main Interface 2: Provides automatic judgment of measurement results (successful/PASS or failed/FAIL) based on set upper and lower thresholds.
- Set Parameter Menu: Allows selection of parameters (green display) and editing of parameters (red display).
Figure 9: Examples of the T459's various display interfaces.
6.3 Measurement and Data Management
- Voltage and Internal Resistance Display Calibration: The device supports fine-tuning of measurement results to ensure accurate readings.
- Data Storage: The tester can record up to 20 sets of internal resistance measurement data. The most recent 5 sets can be viewed directly on the device, while all 20 sets can be accessed via the mobile application.
- Threshold Setting: Upper and lower threshold values can be set for automatic judgment of whether a component is qualified (PASS) or not (FAIL).
6.4 Display and Power Settings
- Backlight Brightness Adjustment: Customize screen brightness with 1-9 levels to suit different environments and user preferences.
- Standby Time Settings: The standby time can be set flexibly from 1 to 9 minutes, which helps in extending battery life and overall service life.
7. Firmware Update (OTA)
The T459 supports Over-The-Air (OTA) firmware updates, enabling remote upgrades or customization without needing to physically connect the device to a computer.
- Ensure the ZK-T459 device is already added to the Wuzhi Zhilian APP.
- In the app, click on the device icon to enter the normal operation interface.
- Click on "OTA". If a new firmware prompt appears, click "confirm". The app will return to the device list, and a 'firmware update' button will appear.
- Alternatively, press and hold the knob button on the device to enter the OTA mode interface.
- In the app, click "Firmware Update" in the top right corner of the device list interface to enter the OTA operation interface. The BT connection icon will be displayed on the device screen.
- Click "Get device information", then "Firmware Update". The app will automatically complete the firmware upgrade.
- Once the progress bar shows complete, the app will automatically disconnect the BT connection. Click the back arrow to return to the APP device list interface.
Figure 10: The OTA firmware update screen on the device and app.
Figure 11: Step-by-step guide for performing an OTA firmware update.
8. Maintenance
- Keep the device clean and dry. Avoid exposure to dust, moisture, and extreme temperatures.
- Use a soft, dry cloth to clean the display and casing. Do not use abrasive cleaners or solvents.
- Store the device in a safe place when not in use to prevent physical damage.
- Regularly check connection cables for any signs of wear or damage. Replace if necessary.
9. Troubleshooting
- Device not powering on: Check power supply connections and ensure the DC 5V input is stable and within limits.
- Inaccurate readings: Ensure proper calibration is performed. Check test lead connections for good contact. Verify the AC 4-wire method is correctly implemented.
- Bluetooth connection issues: Ensure Bluetooth is enabled on your mobile device and the T459. Restart both the app and the tester. Make sure the app is the latest version.
- "FAIL" result on display: This indicates the measured values are outside the set upper and lower thresholds. Review your thresholds or the component being tested.
10. User Tips
- For consistent and accurate results, always use the 4-wire measurement method.
- Utilize the app's historical data feature to track battery performance over time.
- Adjust the backlight brightness to conserve power, especially when operating on battery.
- Take advantage of the automatic judgment feature by setting appropriate upper and lower thresholds for quick quality checks.
11. Warranty and Support
For any warranty claims, technical support, or inquiries regarding your Voktta T459 tester, please refer to the official seller's contact information or the platform where the product was purchased. A detailed user manual in PDF format is available for download: User manual (PDF).