BAOFENG UV-17H GPS

Contents

Baofeng UV-17H GPS Walkie Talkie User Manual

Model: UV-17H GPS

Brand: BAOFENG

1. Safety Warnings and Regulations

Thank you for purchasing this product. This dual-band/dual-display/dual-watch radio provides secure, instant, and reliable communications. Please read this manual carefully before use to ensure maximum performance and safe operation.

1.1 General Safety Warnings

  • WARNING! European Users should note that operation of this unit in Transmit mode requires a valid Amateur Radio License. Failure to comply may be unlawful and liable for prosecution. Refer to the “EU” specification guide 2014/53/EU.
  • ATTENTION! When programming the radio, always read the factory software data first, then rewrite with your desired frequency. Use a programming cable with a PC for authorized frequency, bandwidth, and power settings. Programming must comply with your FCC (or EU other country) license certification.
  • ATTENTION! Before using this product, read the RF Energy Exposure and Product Safety Guide that ships with the radio. This guide contains instructions for safe usage and RF energy awareness and control for compliance with applicable standards and regulations.
  • PMR446, FRS, GMRS, MURS: Using these bands may be subject to restrictions that make this transceiver illegal for use.

1.2 FCC Part 15 / IC Compliance

This device complies with Part 15 of the FCC rules and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.

1.3 RF Exposure and Hand-Held/Body-Worn Operation

  • WARNING! Operate this radio transmitter properly to ensure safe operation. Do not use with a damaged antenna.
  • Hand-Held Operation (Held-to-Face): This device was evaluated for typical hand-held operations with a 1-inch spacing from the front of the radio. Maintain this distance to comply with FCC RF exposure requirements.
  • Body-Worn Operation: This device was evaluated for body-worn operations with the supplied belt-clip accessory. Use only manufacturer-approved accessories to ensure compliance with FCC/Industry Canada RF exposure guidelines.

1.4 Operating Prohibitions and Precautions for Batteries

  • Do not operate the product in locations with fuels, chemicals, explosive atmospheres, or other flammable/explosive materials.
  • Do not operate near blasting areas or medical/electronic equipment vulnerable to RF signals.
  • Do not hold the product while driving.
  • Do not operate in areas where wireless communication equipment is prohibited.
  • Do not use unauthorized or damaged accessories.
  • Keep the product at least 2.5 cm from your body during transmission.
  • Avoid continuous high-volume reception.
  • In vehicles with airbags, do not place the product in the airbag deployment area.
  • Keep the product and accessories out of reach of children and pets.
  • Operate within the specified temperature range.
  • Continuous transmission may cause heat accumulation; allow for cooling.
  • Handle with care; do not disassemble, modify, or repair without authorization.

Battery Charging Prohibitions

  • Do not charge or replace batteries in locations with fuels, chemicals, or explosive materials.
  • Do not charge wet batteries; dry them first.
  • Do not charge deformed, leaking, or overheated batteries.
  • Do not use unauthorized chargers.
  • Do not charge in areas with strong radiation.

2. Product Features

The Baofeng UV-17H GPS Walkie Talkie is a versatile communication device with a range of advanced features:

  • Frequency Range: FM radio 65-108 MHz (RX); VHF1: 136-174MHz (RX&TX); VHF2: 220-260MHz (RX&TX); UHF: 400-520MHz (RX&TX); Police Band: 350-390MHz (RX); Air Band: 108-136MHz (RX).
  • GPS Functionality: Obtain location information for improved coordination efficiency.
  • High Capacity Battery: Equipped with an upgraded 3800mAh thickened Li-ion battery for extended standby time.
  • Type-C Charging: Convenient Type-C USB charging port for flexible charging options (car, power bank, laptop).
  • Wireless Copy Frequency: Easy one-touch search and copy of frequencies from other radios.
  • Large Color Screen: 1.77-inch TFT large screen with full keyboard and fully open menu operation.
  • NOAA Weather Channels: Support for NOAA weather reception in the United States and Canada, with 10 dedicated weather channels.
  • AM/FM Multi-band Function: Broadcast FM radio receiver (65-108 MHz) and AM air band reception (108-136 MHz).
  • DTMF: Dual-Tone Multi-Frequency encoder and manual dial for advanced signaling.
  • VOX Function: Voice-activated transmit for hands-free communication.
  • LED Flashlight: Built-in LED flashlight for emergency lighting.
  • Memory Channels: Up to 999 memory channels for storing frequencies.
  • Scanning Modes: Channel scan, frequency scan, CTCSS/DCS scan with various recovery methods (TO, CO, SE).
  • Power Output: Selectable high or low power (5W/2W).
  • Other Features: Power-on password management, alarm function, programmable repeater offset, transmission time-out timer, busy channel lock out, 10 levels of Squelch adjustment, Roger Beep, Kenwood accessory port (2-pin).
Icons representing key features: Wireless Copy Frequency, 6 Bands, 999 Channels, High Power, 1.77 inch Color Large Screen, GPS, DTMF, Type-C Charging, LED Flashlight, VOX Function, FM Radio, Large Battery.
Key features of the Baofeng UV-17H GPS Walkie Talkie.

3. Package Contents

The standard package for the Baofeng UV-17H GPS Walkie Talkie includes:

  • 1 x Baofeng UV-17H GPS Radio
  • 1 x Antenna
  • 1 x 3800mAh Li-ion Battery Pack
  • 1 x Fast Desktop Charger
  • 1 x Type-C Charging Cable
  • 1 x Belt Clip
  • 1 x Sling
  • 1 x User's Manual (this document)
  • 1 x Box

Note: Different sets may contain different accessories. Please verify your chosen set before use.

Image showing the contents of the Baofeng UV-17H package, including the radio, battery, antenna, charger, belt clip, sling, and manual.
Typical package contents for the UV-17H GPS Walkie Talkie.

4. Radio Overview

4.1 Buttons and Controls

Diagram of the Baofeng UV-17H radio showing numbered parts and their functions.
Front, back, top, and side views of the radio with numbered components.
  1. Antenna
  2. Flashlight/Emergency Alert Key (SK1)
  3. PTT Key
  4. Color LCD
  5. MIC Input
  6. MENU Key
  7. Power/Volume Knob
  8. Numeric Keypad
  9. Accessory Jack
  10. Type-C Charging Port
  11. Battery Pack
  12. Navigation Keys (Up/Down)
  13. Battery Tightening Screw
  14. LED Status Indicator
  15. TX/RX Status LED
  16. LED Flashlight

4.2 LCD Display Icons

IconDescription
RSSISquelch Open/Close Indicator
H/LTransmit power level indicator (High/Low)
DDCS enabled
CCTCSS enabled
+Enables access of repeaters in VFO/Frequency Mode (TX shifted higher than RX)
-Enables access of repeaters in VFO/Frequency Mode (TX shifted lower than RX)
DDual watch enabled
.Keypad lock enabled
NNarrowband enabled
RReverse function enabled
Battery IconBattery level indicator

4.3 Status Indications (LED)

LED IndicatorRadio Status
Constant RedTransmitting
Constant GreenReceiving

5. Setup and Installation

5.1 Charging the Battery Pack

The Li-ion battery pack is not fully charged at the factory. Charge it before first use. For optimal performance, fully charge/discharge the battery two or three times. Use only the specified charger. If the radio displays low battery, charge it immediately.

How to Charge:

  1. Plug the AC adaptor into an AC outlet, then connect the adaptor cable to the DC jack on the charger. The indicator blinks orange, ready to charge.
  2. Plug the battery or the radio (with battery) into the charger. Ensure good contact with charging terminals. The indicator turns red (charging).
  3. Charging takes approximately 2-5 hours. When the lamp turns green, charging is complete. Remove the battery/radio from the charger.

LED Indicator during Charging:

STATUSLED
No BatteryGreen and red alternately flashing
Charge NormallyRed
Fully ChargedGreen
TroubleRed blinks fast for a long time

NOTE: Trouble indicates battery too warm, short-circuited, or charger short-circuited.

Using the Type-C USB Charger:

The Type-C USB port allows convenient charging of your Li-ion battery pack.

  1. Ensure your radio is turned OFF.
  2. Plug the Type-C USB cable into the Type-C charging port on your battery. Connect the other end to a wall power outlet.
  3. An empty battery will fully charge in approximately 4 hours.
  4. The battery meter on the LCD will indicate charging progress.

Note: It is recommended to power OFF your radio while charging. For optimal battery life, remove the radio from the charger within 6 hours. Do not store the radio connected to the charger.

Diagram showing Type-C charging methods for the radio, including USB charging, computer charging, power bank charging, and car charging.
Type-C charging options for your radio.

5.2 Installing/Removing the Antenna

  • Installing: Screw the antenna into the connector on top of the transceiver by holding its base and turning clockwise until secure.
  • Removing: Turn the antenna counter-clockwise to remove it.

5.3 Installing the Belt Clip

At the back of the radio, there are two parallel screws above the battery. Remove these, thread them through the belt clip holes, and screw them back into the radio body.

5.4 Installing the Battery Pack

Before attaching or removing the battery, ensure the radio is turned off by rotating the power/volume knob counter-clockwise.

  1. Align the battery in parallel with the radio body, with its lower edge about 1-2cm below the radio's edge.
  2. Slide the battery upward along the guide-rails until it clicks into place.

Removing the Battery Pack:

Press the battery release above the battery pack and slide the battery downward.

5.5 Installing Additional Speaker/Microphone (Optional)

Pry open the rubber MIC-Headset jack cover and insert the Speaker/Microphone plug into the double jack.

6. Basic Operations

6.1 Power On/Off the Radio

  • Turning On: Rotate the Volume/Power knob clockwise until you hear a "click". The radio will emit a double beep, display a message or flash the LCD, then show a frequency or channel. If voice prompt is enabled, it will announce "frequency mode" or "channel mode".
  • Turning Off: Rotate the Volume/Power knob counter-clockwise until you hear a "click". The unit is now off.

6.2 Adjusting the Volume

Rotate the Volume/Power knob clockwise to increase volume, counter-clockwise to decrease. Be careful not to turn it too far, which may turn off the radio. Use the monitor function (via [SK2] key) to hear un-squelched static for easier adjustment.

6.3 Main Band/Sub Band Select

In standby mode, press the [A/B] key to switch between the A (upper) and B (lower) displays. The selected display's frequency or channel becomes active for listening and transmitting. To save frequencies to channel memory, you must be on the A display.

6.4 VFO/Channel Switch

Press and hold the [MENU] key to switch between VFO (Frequency) mode and Channel (MR) mode. In Channel mode, the channel number is displayed. In VFO mode, 'VFO' is displayed.

6.5 Frequency (VFO) Mode

In VFO mode, navigate up/down the band using the [UP] or [DOWN] keys, incrementing/decrementing by the set frequency step. You can also input frequencies directly using the numeric keypad with kilohertz accuracy.

6.6 Channel (MR) Mode and Channel Selection

Channel (MR) mode is practical for everyday use, while VFO mode is useful for experimentation and programming. In MR mode, navigate channels using the [UP] or [DOWN] keys or by entering channel numbers directly via the keypad.

6.7 Making a Call

  • Channel Mode Call: Select a channel, then hold down the [PTT] key to transmit. Speak into the microphone with a normal tone. The red LED will be on.
  • Frequency Mode Call: Switch to frequency mode, input the desired working frequency, then hold down the [PTT] key to transmit. The red LED will be on.
  • Receive a Call: When you release the [PTT] key, you can receive calls. The green LED will be on when receiving.

NOTE: For best reception volume, keep the microphone 2.5 cm to 5 cm from your mouth during transmission.

6.8 Using the Flashlight

Press the [SK1] key momentarily to turn on the high-intensity LED flashlight. Another press will make it flash (strobe mode). A third press turns it off. The radio operates normally when the strobe is active.

6.9 Emergency Alert

Press and hold the [SK1] key for 3 seconds to activate the emergency alert. The radio will emit a loud siren and the flashlight will flash. Press [SK1] again to exit. WARNING: Use this feature only in actual emergencies.

6.10 FM Radio (FM)

The radio can receive FM broadcasts in the 65-108MHz range. Press [SK2] to switch between 65-75 MHz and 76-108 MHz bands.

  1. In frequency or channel mode, press [SK2] to turn on the radio.
  2. Select the desired radio frequency with the [UP] or [DOWN] keys or input directly. Press [#] to automatically search for a radio station.
  3. Press [SK2] to exit FM radio.

Note: While listening to FM, if a signal is received on the A/B receiving frequency/channel, the radio will automatically switch to that frequency/channel. It will return to FM mode when the signal disappears.

6.11 Monitor

In standby, press and hold the [SK2] key to enter Monitor mode. This opens the squelch, allowing you to hear weak signals or unfiltered audio. Release [SK2] to return to standby. If no signal is present, it will emit noise.

6.12 Keypad Lock

The keypad lock disables all keys except the three side keys. To enable/disable, press and hold the [*] key for about two seconds. The radio can also be set to automatically lock after ten seconds via the menu.

6.13 Frequency Reversal

A short momentary press of the [*] key enables the reverse function. This allows you to listen to the repeater's input frequency. The screen will display "R" when active.

6.14 TX Repeaters Tone

Press [PTT] + [MENU] key to send a 1750Hz repeater tone. This is useful for communicating through repeaters. This function works even if the keypad lock is enabled.

Step-by-step visual guide for wireless copy frequency, showing the radio display during search and confirmation.
Wireless Copy Frequency: Step-by-step guide.
  1. Press and hold the [MENU] key. The screen will display "SEARCH SEARCH...".
  2. If the transmitter continues to transmit and the unit receives an effective frequency, it will be displayed. If CTCSS or DCS is present, its value will be shown; otherwise, "NONE" is displayed.
  3. Press the [MENU] key to save the searched frequency and CTCSS or DCS to a channel.

Note: During frequency search, press the [#] key to switch between UHF or VHF bands.

6.16 NOAA Weather Channels

Your radio has a NOAA Weather Radio function to receive weather reports and a NOAA Weather Scan function to scan all 10 NOAA Weather Radio channels.

Image showing the Baofeng UV-17H radio with '10 NOAA Weather Channels' text, indicating its ability to cope with severe weather conditions.
Accessing NOAA Weather Channels for timely weather information.
  1. To turn on NOAA Weather Scan, press and hold the [0sQL] key for 3 seconds. The radio will enter Weather band mode.
  2. Press and hold the [#] key for 3 seconds to start automatic scanning of all 10 channels. It will stop on active channels. Pressing and holding [#] again stops the scan.
  3. After stopping the scan, you can manually select weather channels using the [UP] or [DOWN] keys.
  4. To exit Weather Radio broadcast mode, press the [MENU] key or [PTT] key.

Weather Channel Frequencies:

Channel NumberRX Frequency MHzChannel NumberRX Frequency MHz
Wx-01162.550Wx-06162.500
Wx-02162.400Wx-07162.525
Wx-03162.475Wx-08161.650
Wx-04162.425Wx-09161.775
Wx-05162.450Wx-10163.275

NOTE: Weather Channels Wx 1 Thru 10 are Receive-only channels for NOAA and Canadian weather broadcasts. You cannot transmit on these channels.

7. Advanced Features and Menu System

7.1 Working the Menu System

The radio's menu system allows customization of various settings. For a complete reference, refer to Appendix B. If the radio is in Memory (MR) mode, some menu items (STEP, TXP, W/N, CTCSS, DCS, S-CODE, PTT-ID, BCL, SFT-D, OFFSET, MEM-CH) will not take effect.

Basic Use with Arrow Keys:

  1. Press [MENU] key to enter the menu.
  2. Use [UP]/[DOWN] keys to navigate.
  3. Press [MENU] again to select an item.
  4. Use [UP]/[DOWN] keys to select a parameter.
  5. To confirm, press [MENU]. To cancel, press [EXIT].
  6. To exit the menu at any time, press [EXIT].

Using Shortcuts:

Each menu item has a numerical value for direct access.

  1. Press [MENU] key.
  2. Enter the menu item number using the numeric keypad.
  3. Press [MENU] to enter the item.

7.2 Scanning

The radio features a built-in scanner for VHF and UHF bands. In VFO mode, it scans in steps according to your set frequency step. In Channel (MR) mode, it scans your channels. Dual Watch is inhibited during scanning.

To Enable Scanner:

Press and hold the [#] key for about two seconds. Press and hold [#] again to exit scanning mode.

Scanning Modes (Menu 21):

The scanner can operate in three modes: Time (TO), Carrier (CO), or Search (SE).

  • Time Operation (TO): Scanner stops on a signal, resumes after a preset time.
  • Carrier Operation (CO): Scanner stops on a signal, resumes after a preset time if the signal disappears.
  • Search Operation (SE): Scanner stops on a signal and waits. Press [#] to resume.

Setting Scanner Mode:

  1. Press [MENU].
  2. Enter 21 on the numeric keypad.
  3. Press [MENU] to select.
  4. Use [UP]/[DOWN] keys to select the desired mode.
  5. Press [MENU] to confirm and save.
  6. Press [EXIT] to exit.

7.3 Manual Programming (Channels Memory)

The radio features 999 memory channels. Each channel can store receive/transmit frequencies, power, signaling info, bandwidth, ANI/PTT-ID, and a six-character alphanumeric name.

Example: Programming a Channel Repeater Offset with CTCSS Tone

Let's program Channel 10 with RX = 432.55000 MHz, TX = 437.55000 MHz (+5 Offset), and TX CTCSS tone 123.0.

  1. Press [MENU] to switch between menus.
  2. Press and hold [MENU] to set the radio to VFO mode.
  3. Enter [3][1][1] then [MENU] [0] to delete prior data in Channel 10.
  4. Enter [1][2] then [MENU] [123.0] to select TX encode tone.
  5. Enter RX frequency (e.g., 43255000).
  6. Enter [3][0] then [MENU] [10] to enter the desired channel (10). RX has been added.
  7. Enter TX frequency (e.g., 43755000).
  8. Enter [3][0] then [MENU] [10] to enter the same channel (10). TX has been added.
  9. Press and hold [MENU] to return to MR mode.

7.4 VOX (Voice Activated Transmit)

This function enables hands-free conversations. Speak into the microphone, and the radio will automatically transmit.

Enabling/Disabling VOX (Menu 7):

  1. In standby mode, press [MENU] + 7. The screen displays "VOX".
  2. Press [MENU] to enter.
  3. Use [UP]/[DOWN] keys to turn off VOX or select level (1-10).
  4. Press [MENU] to confirm.
  5. Press [EXIT] to return to standby.

NOTE: Level 1 is least sensitive, level 9 is most sensitive. VOX is not enabled in Scan or FM Radio mode.

7.5 Dual Watch

This feature allows monitoring two channels simultaneously. The radio can flip-flop between two frequencies at a fixed interval.

Enabling/Disabling Dual Watch (Menu 7):

  1. Press [MENU].
  2. Enter 7 on the numeric keypad.
  3. Press [MENU] to select.
  4. Use [UP]/[DOWN] keys to enable or disable.
  5. Press [MENU] to confirm.
  6. Press [EXIT] to exit.

7.6 DTMF (Dual-Tone Multi-Frequency)

DTMF is an in-band signaling method used for automation and remote control, common in amateur radio repeaters. The radio has full DTMF implementation, including A, B, C, and D codes.

DTMF Frequencies and Corresponding Codes:

1209Hz1336Hz1477Hz1633Hz
697Hz123A
770Hz456B
852Hz789C
941Hz*0#D

To send DTMF codes, press the corresponding number/symbol keys while holding down the [PTT] key. This works even with keypad lock enabled.

7.7 Customization

The radio allows customization of visual and audible features.

  • Display Backlight (ABR) - Menu 7: Set delay time (ON/5sec/10sec/15sec/20sec).
  • Beep Prompt (BEEP) - Menu 8: Enable/disable key press beep tone.
  • Voice Function (VOICE) - Menu 17: Enable/disable voice prompts.
  • Language of the Menu (LANGUAGE) - Menu 18: Select English or Chinese.
  • Working Mode (MDF-A) - Menu 24: Choose display mode (Frequency, Channel, Name).
  • Roger Beep (ROGER) - Menu 36: Enable/disable end-of-transmission tone.
  • Power On Message (POWER ON MSG) - Menu 40: Customize welcome message (Voltage, Message, Logo, Model Name).
  • Power On Password (POWER ON PWD) - Menu 43: Enable/disable password requirement at startup.

7.8 Reset - Menu 51

The transceiver has two reset modes:

  • Reset VFO: Resets all settings except channels to default.
  • Reset ALL: Resets all settings to default.

8. Maintenance

8.1 Battery Maintenance

  • Clean accumulated dust on charging connectors regularly with a clean, dry cloth.
  • Charge the battery between 5°C and 40°C.
  • Turn off the radio when charging the battery attached to it.
  • Do not remove the battery or unplug the power cord during charging.
  • Do not dispose of the battery in fire.
  • Do not expose the battery to direct sunlight or other heat sources.
  • Do not squeeze, penetrate, or remove the housing of the battery.
  • Store batteries at 80% discharged in a low-temperature, dry environment, away from hot places and direct sunlight.

8.2 General Radio Maintenance

  • Keep the radio dry; moisture can corrode electronic circuits.
  • If the radio emits a peculiar smell or smoke, immediately shut off power and remove the charger/battery.
  • Do not transmit without an antenna.
  • Do not attempt to open or realign the radio; this will void the warranty.
  • Do not store the radio in direct sunlight, hot areas, or dusty/dirty environments.

9. Troubleshooting Guide

PhenomenaAnalysisSolution
Cannot turn on the radio.Battery installed improperly, power run out, or dirty/damaged contacts.Remove/reattach battery, recharge/replace battery, clean contacts.
Weak or intermittent voice during reception.Battery voltage low, volume low, antenna loose/incorrectly installed, speaker blocked.Recharge battery, increase volume, reattach antenna, clean speaker.
Cannot communicate with other group members.Inconsistent frequency/signaling type, too far from others.Verify TX/RX frequency/signaling type, move closer to others.
Hear unknown voices or noise.Interrupted by radios on same frequency, analog mode without signaling.Change frequency, adjust squelch level, set signaling for current channel.
Unable to hear due to too much noise/hiss.Too far from others, unfavorable position (blocked by buildings), external disturbance.Move closer, move to open/flat area, restart radio, stay away from interference.
Radio keeps transmitting.VOX turned on, headset not in place.Turn off VOX, check headset.

NOTE: If these solutions do not resolve your problems, contact your dealer for technical support.

10. Technical Specifications

General
Frequency Range136-174MHz(TX&Rx), 220-260MHz(TX&Rx), 400-520 MHz(TX&Rx), FM65-108MHz
Power5W/2W
Channel Spacing25.0KHz(Wide)/12.5KHz(Narr)
Memory Channel999 Groups
Operation VoltageDC 7.4 V ±10%
Transmission current≤1800mA
Dimensions132x56x35mm (no include antenna)
MaterialPlastic
Waterproof / Water-ResistantIP45
CertificationCE, Dot, EAC, EPA, FCC, GMP, RoHS, TGA, UL, KC, pse, weee
Transmitter
Output Power(w)5w-10w
Modulation16K0F3E/11K0F3E
Spurious Emission-16 dBm<1GHz, -16 dBm>1GHz
Frequency Stability±2.5 ppm
Audio Distortion≤5%
FM Hum & Noise40 dB
Receiver
Receive Sensitivity0.25μV (12dB SINAD)
Rated Audio Power Output1W @16 ohms
Receive current≤380mA
Intermodulation and Rejection-70 dBm
Rated Audio Distortion≤5%
Antenna Impedance50 Ohm
Connection for accessories2 pin Kenwood jack

NOTE: All specifications may be modified without prior notice or liability.

Diagram showing the dimensions of the Baofeng UV-17H radio, including height with antenna, body height, width, and thickness.
Physical dimensions of the Baofeng UV-17H GPS Walkie Talkie.

11. User Tips

  • Battery Care: To maximize battery life, avoid overcharging. Remove the radio from the charger once the green light indicates a full charge, especially for Type-C charging.
  • Antenna Handling: Always screw the antenna securely into place. A loose or damaged antenna can affect performance and potentially cause burns if it contacts skin during transmission.
  • Frequency Modes: Understand the difference between VFO (Frequency) mode for direct frequency input and MR (Channel) mode for pre-programmed channels. Use VFO mode for programming new channels.
  • Keypad Lock: Utilize the keypad lock feature (press and hold [*]) to prevent accidental key presses, especially when carrying the radio.
  • NOAA Weather: Regularly check NOAA weather channels for critical updates, especially during outdoor activities or in areas prone to severe weather. Remember these are receive-only channels.
  • Programming: For complex programming, such as repeater offsets or custom channel names, using the PC programming software is recommended for accuracy and ease.

12. Warranty and Support

The Company endeavors to achieve the accuracy and completeness of this manual, but no warranty of accuracy or reliability is given. All specifications and designs are subject to change without notice due to continuous technological development. No part of this manual may be copied, modified, translated, or distributed in any manner without the prior written consent of the Company.

We do not guarantee, for any particular purpose, the accuracy, validity, timeliness, legitimacy, or completeness of the third-party products and contents involved in this manual.

For technical support or warranty inquiries, please contact your original point of purchase or the manufacturer's authorized service center. Keep your purchase receipt as proof of purchase.

Print version: BF-17L_V1.0

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.