Godox IT32

Contents

Godox iFlash IT32 TTL Camera Flash & X5 Wireless Trigger User Manual

Model: IT32 & X5 Series

1. Important Safety Instructions

This product is a professional photographic equipment, to be operated by professional personnel only.

All transport protective materials and packaging on the product must be removed before use.

The following basic safety precautions must be followed when using this product:

  1. Carefully read and fully understand the instruction manual before use and strictly follow the safety instructions. Failure to do so may result in serious injury, damage to the product, or other property damage.
  2. High voltage exists when the flash is powered on. Internal capacitors will remain charged for some time after power off.
  3. This product is a professional lighting fixture, children are prohibited from using it. Children must be closely supervised by adults when approaching the fixture, to prevent collisions with the fixture or unauthorized use that could cause personal injury.
  4. This is not an ordinary lighting fixture and must not be used for general illumination. Anyone with a history of eye damage or sensitivity should avoid using this fixture or looking directly at it.
  5. Extreme caution must be exercised when using it, do not touch high-temperature parts such as flash tubes to avoid burns.
  6. Do not point the flash directly at the eyes (especially baby's eyes) under any circumstances, as this could impair vision in a short time. Turn off immediately if discomfort occurs, stop using, and seek medical attention promptly.
  7. When using the camera flash with a reflector at a focal length of 14mm, continuous use of 1/1 step for a long time is strictly prohibited due to the extremely close focal length. After reaching the maximum number of flashes before over-temperature protection activates, a pause of 10 minutes is required before resuming use.
  8. If the flash tube is damaged, stop using it immediately and contact the manufacturer, service agent, or qualified repair personnel for a replacement to prevent accidents.
  9. Do not use damaged equipment or accessories. Allow professional repair technicians to inspect and confirm normal operation before continuing use after repairs.
  10. Disconnect power source or remove batteries (if it has one) before replacing flash tube, protective glass, or fuses. Allowing 10 minutes to cool before replacing flash tube, and wear insulated or heat resistant gloves when operating.
  11. Stop using immediately if the product shell is cracked due to falling, squeezing, or strong impact, to avoid touching the internal electronic components and getting an electric shock.
  12. This device is not waterproof. Keep it dry and avoid immersing it in water or other liquids. It should be installed in a ventilated and dry location and avoid using in rainy, humid, dusty, or overheated environments. Do not place items above the device or allow liquids to flow into it to prevent danger.
  13. Do not disassemble without authorization. If the product malfunctions, it must be inspected and repaired by our company or authorized repair personnel.
  14. Before storing the device, make sure it is completely cooled, then put it in the protective case or a ventilated dry location.
  15. Do not place the device near alcohol, gasoline, or other flammable volatile solvents or gases such as methane and ethane.
  16. Do not use or store this device in potentially explosive environments.
  17. Do not use accessories not been approved by our company, as this may cause fire, electric shock or personal injury.
  18. Clean gently with a dry cloth. Do not use a wet cloth as it may damage the device.
  19. Some products are equipped with protective covers that must be removed before use.
  20. This instruction manual is based on rigorous testing. Changes in design and specifications are subject to change without notice. Check official website for latest instruction manual and product updates.
  21. Use only specified charger and follow proper usage instructions for certain products with built-in lithium batteries, within the rated voltage and temperature range.
  22. This product is powered by lithium batteries, who have limited lifespans and will gradually lose their charging capacities, which is irreversible. As the battery ages, the product's battery life will decrease. The lifespan of lithium battery is estimated to be 2 to 3 years.
  23. Some products are equipped with lithium batteries. The following are the storage recommendations: Charge the battery to about 50% before storage. Charge it to about 50% at least every six months. Removable batteries should be stored separately. The storage temperature should be between 0°C and 40°C.
  24. For products powered by lithium batteries. Please note:
    • Do not disassemble, crush, or puncture the battery;
    • Avoid short-circuiting the battery contacts;
    • Do not expose the battery to fire or water;
    • Do not expose the battery to temperatures above 60°C;
    • Keep out of reach of children;
    • Protect the battery from excessive shock or vibration;
    • Do not use a damaged battery;
    • If the battery leaks, avoid contact with the leaking fluid;
    • If the battery fluid comes into contact with your eyes, immediately rinse with water for at least 15 minutes. Lift your eyelids until there are no signs of fluid and seek medical attention promptly.
  25. Confirm and comply with all relevant local laws and regulations when handling any batteries.
  26. The warranty period for this device as a whole is one year. Consumables (such as batteries), adapters, power cords, and other accessories are not covered by the warranty.
  27. Unauthorized repairs will void the warranty and will incur charges.
  28. Please check the status and power of the lithium battery upon receipt. If there are any quality issues, please contact Godox or our authorized dealer within the warranty period.
  29. Failures from improper operation is not covered under warranty.

2. Introduction

Thank you for purchasing the Godox iFlash IT32 TTL Camera Flash! The iT32 is a powerful and compact flash product with excellent performance. With a built-in Godox 2.4G wireless X system, integrated Wi-Off/Sender/Receiver modes, it is fully compatible with TTL/M/Multi modes across mainstream camera brands like Canon, Sony, Nikon, OM SYSTEM, and Fujifilm. This allows for convenient shooting even in frequently changing lighting conditions.

Main Features

  • Separated Triggering: Remove the X5 trigger from the iT32 flash and insert it into the camera hot shoe mount. This enables wireless control of flash, mode switching, and power adjustment. (X5 is sold separately).
  • Convenient Operation: Features an intuitive colorful touch screen and simplified traditional buttons for easy interaction.
  • Professional and Portable: Supports auto flash, manual flash, multi flash, HSS, second-curtain sync, and FEC functions within a lightweight body of merely 169g (without X5).
  • 2.4G Wireless System: The built-in Godox 2.4G wireless X system ensures stable signal transmission and anti-interference capabilities in complex environments.
  • TTL Compatibility: Perfectly supports TTL auto flash to simplify the shooting procedure by automatically adjusting flash output.
  • Precise Lighting Control: Power adjustment range from 1/128 to 1/1, with ±1/3 increment fine-tuning.
  • Efficient Power Supply: Equipped with a 7.2V/900mAh lithium battery that supports USB-C charging, offering a 1.5s recycle time and 510 full-power flashes.
  • LED Modeling Lamp: Supports brightness adjustment from level 1 to level 10.
  • Firmware Upgrade: Firmware is updated regularly to be compatible with the latest camera models and ensure optimal performance.
Video: Godox iT32 Flashlight Product Overview - This video demonstrates the key features and usage scenarios of the Godox iT32 flashlight, including its detachable design, TTL & TCM functions, rotating head, wireless sync, diffusion panels, and magnetic accessories.

3. Product Overview

What's in the Box

Contents of the Godox iT32 package including flash body, USB-C charging cable, magnetic mini stand, and diffuser.
Figure 3.1: iT32 Package Contents - The package includes the iT32 flash body, a USB-C charging cable, a magnetic mini stand, and a diffuser.
  • Flash Body ×1
  • USB-C Charging Cable ×1
  • Magnetic Mini Stand ×1
  • Diffuser ×1
  • Magnetic Color Filter (1/2 orange) ×1
  • Magnetic Color Filter (1/1 orange) ×1
  • Storage Bag ×1
  • Instruction Manual ×1

Separately Sold Accessories

Purchase the following Godox accessories to achieve best photography effects:

Various Godox flash triggers and magnetic accessory kit.
Figure 3.2: Optional Accessories - This image shows additional accessories such as the X2T, XProII, and X3 flash triggers, and the MA02 Magnetic Accessory Kit.
  • Flash trigger X2T series
  • Flash trigger XProII series
  • Flash trigger X3 series
  • TTL wireless flash trigger X5 series (X5C/X5N/X5S/X5F/X5O)
  • Magnetic Accessory Kit MA02

Name of Parts

Diagram of the Godox iT32 flash body with numbered parts.
Figure 3.3: iT32 Flash Body Parts - A detailed diagram highlighting the components of the iT32 flash body.
  1. Flash Head
  2. Wide-angle Diffuser (Transparent, inside the flash head)
  3. Catchlight Panel (White, inside the flash head)
  4. LED Modeling Lamp
  5. Photocell Sensor
  6. Sync Cord Jack
  7. USB-C Port (Charging/firmware upgrade)
  8. Touch Screen
  9. MENU Button
  10. SET Button
  11. < - / + > Button
  12. Select Dial
  13. Select Dial Alignment Marker
Diagram of the Godox X5 wireless flash trigger with numbered parts.
Figure 3.4: X5 Wireless Flash Trigger Parts - A detailed diagram highlighting the components of the X5 wireless flash trigger.
  1. Indicator
  2. < - / > Button
  3. < + / M > Button
  4. Hot Shoe Locking Ring
  5. Hot Shoe

Note: The appearances and contacts of hot shoes vary in different models.

4. Setup

Installing the Flash Trigger (X5)

Align the flash trigger with the bottom of the flash body in the direction as shown and place it in; the flash will automatically absorb it. Once installed, the < C > icon in the menu interface will light up.

Diagram showing how to install the X5 flash trigger onto the iT32 flash body.
Figure 4.1: Installing X5 Trigger - Visual guide for attaching the X5 trigger to the iT32 flash.

Installing the Diffuser

Align the protruding side of the diffuser with the model <iT32> logo side of the flash body, then insert it firmly until fully seated.

Diagram showing how to install the diffuser onto the iT32 flash head.
Figure 4.2: Installing Diffuser - Visual guide for attaching the diffuser to the iT32 flash head.

Mounting on the Camera

Rotate clockwise the hot shoe locking ring of the flash trigger to the top and insert into the hot shoe mount of the camera, then rotate anticlockwise the hot shoe locking ring until it's firmly locked.

Diagram showing how to mount the iT32 flash onto a camera's hot shoe.
Figure 4.3: Mounting on Camera - Visual guide for securely attaching the flash to your camera's hot shoe.

Note: Please make sure the flash and camera are powered off before installing and disassembling.

5. Operation

Power Switch

  • Power on: Press and hold the < 4/0 > button until the icon appears, then slide up on the screen or rotate up the select dial to unlock. The device will turn off automatically if it stays locked for 6 seconds after power on (This function can be turned off in bootup settings, then press and hold the < 4/0 > button can directly power on the device).
  • Power off: Press and hold the < 4/0 > button until the screen blacks out.

The flash trigger X5 does not have power on/off function. Users can check its status via the indicator according to the following table:

IndicatorDescription
Flash greenUnconnected to camera in TTL mode
Constant on greenConnected to camera in TTL mode
Flash orangeUnconnected to camera in M mode
Constant on orangeConnected to camera in M mode
Flash red slowlyLow battery level
Light offSleep mode, press any button to wake

Battery Level Indication

iT32

Check the battery level indication on the panel to see the remaining battery level.

Battery Level IndicationMeaning
3 gridsFull
2 gridsMiddle
1 gridLow
Blank gridLower battery, please recharge it.
BlinkingThe battery level is going to be used out, and the flash is not functional in this status.

Note: Please recharge the battery as soon as possible (within 10 days). Then, the battery can be used or be placed for long period.

X5

  • Check on the Flash: Install X5 to iT32, slide the screen top-down to enter menu interface, find the < C > and click to check the model and battery level of flash trigger.
  • Check via the Indicator: When MG1 and iT32 are unconnected, press and hold the < - / > button of flash trigger until the indicator turns red. Then check the battery level by observing the number of red flashes from the indicator. (One flash indicates low battery, four flashes indicate full charge, and so on.)

Charging Instructions

  • iT32: It takes approx. 1h10min to fully charge the camera flash with USB-C charging cable, and provides approx. 510 full power flashes in full battery level.
  • X5: It takes approx. 3h to fully charge the flash trigger after connected to iT32, and approx. 16h to discharge in full battery level.

Wi-Off Mode (With Flash Trigger X5)

This mode is used when the iT32 flash is mounted directly on the camera hot shoe with the X5 trigger attached.

Screenshot of the iT32 touch screen in Wi-Off mode showing TTL settings.
Figure 5.1: Wi-Off Mode Interface (TTL) - The main screen for TTL auto flash in Wi-Off mode.

TTL: TTL Auto Flash

In TTL mode, the camera's metering system detects the flash reflected from the subject and automatically adjusts the flash output so that the subject and background are evenly exposed.

  • Touch Screen: Slide the screen top-down to enter menu interface, click the <TTL/M/Multi> icon to choose <TTL> and enter TTL auto flash mode.
  • Buttons and Select Dial: Press the MENU button to enter menu interface, rotate the select dial to choose the <TTL/M/Multi> icon, then press the SET button to choose <TTL> and enter TTL auto flash mode.
  • FEC Amount Adjustment: Press the < - / + > icon or rotate the select dial in the main interface to adjust the FEC amount from -3.0 to +3.0 with ±1/3 increment each step, or directly pull the progress bar to achieve quick adjustment.

Note: When the shutter is fully pressed, the flash will fire a pre-flash that the camera will use to calculate exposure and flash output the instant before the photo is taken.

M: Manual Flash

S1 and S2 photocell functions are available in M mode, and the flash output is adjustable. To obtain a correct flash exposure, use a handheld flash meter to determine the required flash output.

  • Touch Screen: Slide the screen top-down to enter menu interface, click the <TTL/M/Multi> icon to choose <M> and enter M manual flash mode.
  • Buttons and Select Dial: Press the MENU button to enter menu interface, rotate the select dial to choose the <TTL/M/Multi> icon, then press the SET button to choose <M> and enter M manual flash mode.
  • Output Power Adjustment: Press the < - / + > icon or rotate the select dial in the main interface to adjust the power from 1/128 to 1/1 with ±1/3 increment each step, or directly pull the progress bar to achieve quick adjustment.

S1/S2 Photocell

The photocell sensor will enter standby mode to continuously monitor changes in ambient light levels after the photocell triggering is turned on.

  • S1 Photocell Unit: With this function, the flash will fire synchronously when the main flash fires, the same effect as that by the use of wireless triggers. This helps create multiple lighting effects.
  • S2 Photocell Unit (pre-flash): This is useful when cameras have pre-flash function. With this function, the flash will ignore a single "pre-flash" from the main flash and will only fire in response to the second, actual flash from the main unit.

Note: Enter setting interface to switch between S1/S2 photocell or turn off this function.

Multi: Stroboscopic Flash

In multi flash mode, a rapid series of flashes is fired. It can be used to capture multiple images of a moving subject in a single photograph. You can set the number of flashes, flash frequency (number of flashes per sec. expressed as Hz), and flash output.

  • Number of flashes: 1-100
  • Flash frequency: 1-100
  • Flash output range: 1/128-1/4
  • Touch Screen: Slide the screen top-down to enter menu interface, click the <TTL/M/Multi> icon to choose <Multi> and enter multi flash mode. Press the < - / + > icon or directly pull the progress bar can adjust the flash power. Press the times/frequency icon on the upper right corner to enter the number of flashes and flash frequency adjustment interface, slide the numbers up or down to adjust the respective parameters.
  • Buttons and Select Dial: Press the MENU button to enter menu interface, rotate the select dial to choose the <TTL/M/Multi> icon, then press the SET button to choose <Multi> and enter multi flash mode. Directly rotate the select dial can adjust the output power. Press the SET button to choose the times/frequency icon on the upper right corner, then rotate the select dial can adjust the respective parameters.
Screenshot of the iT32 touch screen in Multi flash mode.
Figure 5.2: Multi Flash Mode Interface - The main screen for stroboscopic flash settings.
Calculating the Shutter Speed in Multi Flash Mode

During multi flash, the shutter remains open until the firing stops. Use the formula below to calculate the shutter speed and set it with the camera.

Number of Flashes ÷ Flash Frequency = Shutter Speed

For example, if the number of flashes is 10 and the flash frequency is 5Hz, the shutter speed should be at least 2 seconds.

Note:

  1. Multi flash is most effective with a highly reflective subject against a dark background.
  2. Using a tripod and TTL flash trigger is recommended.
  3. A flash output of 1/1 and 1/2 cannot be set for multi flash.
  4. Multi flash can also be used with "BULB" mode.
  5. Multi flash mode cannot be set in high-speed sync, second-curtain sync and first-curtain sync modes.

Sender Mode (With Flash Trigger X5)

In Sender Mode, the iT32+X5 acts as a master unit to control other Godox flashes.

  • Touch Screen: Slide the screen top-down to enter menu interface, click the < ( (p) > icon to choose < ( (p) > and enter sender mode.
  • Buttons and Select Dial: Press the MENU button to enter menu interface, rotate the select dial to choose the < ( (p) > icon, then press the SET button to choose < ( (p) > and enter sender mode.

Gr: Sender Group

The flash mode, output power and FEC amount of receiver unit can be individually adjusted in Gr mode.

  • Groups: M, A, B, C (iT32+X5S/N/F/O); A, B, C, D (iT32+X5C)
  • Flash Modes: TTL auto flash mode/M manual flash mode
  • Touch Screen: Slide the screen top-down to enter menu interface, click the <Gr/Multi> icon to choose <Gr>. The flash power and FEC amount are adjustable by clicking the < - / + > icon, or quickly adjustable by pulling the progress bar. Press and hold the group box to switch among M (manual) flash, TTL auto flash and OFF.
  • Buttons and Select Dial: Press the MENU button to enter menu interface, rotate the select dial to choose the <Gr/Multi> icon, then press the SET button to choose <Gr>. Press the MENU button to enter the main interface, rotate the select dial to choose a certain group. Then press the SET button to enter the group settings, and rotate the select dial to adjust the flash power and FEC amount. Press and hold the SET button to switch among M (manual) flash, TTL auto flash and OFF.

Note: If the value inside is in green color, it's in TTL auto flash mode. If the value inside is in white color, it's in M (manual) flash mode.

Receiver Mode (With Flash Trigger X5)

As a receiver unit, iT32+X5 are controllable by other Godox flash triggers with 2.4G wireless function.

  • Touch Screen: Slide the screen top-down to enter menu interface, click the < ( (p) > icon to choose < ( (p) > and enter sender mode.
  • Buttons and Select Dial: Press the MENU button to enter menu interface, rotate the select dial to choose the < ( (p) > icon, then press the SET button to choose < ( (p) > and enter sender mode.

TTL: TTL Auto Flash

  • Touch Screen: Slide the screen top-down to enter menu interface, click the <TTL/M/Multi> icon to choose <TTL> and enter TTL auto flash mode.
  • Buttons and Select Dial: Press the MENU button to enter menu interface, rotate the select dial to choose the <TTL/M/Multi> icon, then press the SET button to choose <TTL> and enter TTL auto flash mode.
  • Group Selection: Press the group icon, or press the SET button and rotate the select dial to choose a certain group.

M: Manual Flash

  • Touch Screen: Slide the screen top-down to enter menu interface, click the <TTL/M/Multi> icon to choose <M> and enter M manual flash mode.
  • Buttons and Select Dial: Press the MENU button to enter menu interface, rotate the select dial to choose the <TTL/M/Multi> icon, then press the SET button to choose <M> and enter M manual flash mode.
  • Group Selection: Press the group icon, or press the SET button and rotate the select dial to choose a certain group.
  • Output Power Adjustment: Press the < - / + > icon or rotate the select dial to adjust the power from 1/128 to 1/1 with ±1/3 increment each step, or directly pull the progress bar to achieve quick adjustment.

Multi: Stroboscopic Flash

The number of flashes, flash frequency and output power of receiver unit can be universally adjusted in multi mode.

  • Touch Screen: Slide the screen top-down to enter menu interface, click the <TTL/M/Multi> icon to choose <Multi>, then slide the screen up to enter the main interface. Press the group icon on the upper left corner to choose a certain group. Press the < - / + > icon or directly pull the progress bar can adjust the flash power. Press the times/frequency icon on the upper right corner to enter the number of flashes and flash frequency adjustment interface, slide the numbers up or down to adjust the respective parameters.
  • Buttons and Select Dial: Press the MENU button to enter menu interface, rotate the select dial to choose the <TTL/M/Multi> icon, then press the SET button to choose <Multi>. Press the MENU button to enter the main interface, directly rotate the select dial can adjust the output power. Press the SET button and rotate the select dial to choose among number of flashes, flash frequency, group and output power, then press the SET button and rotate the select dial can adjust the respective parameters.

Note: The details of which please refer to the section Wi-Off mode → multi: stroboscopic flash above.

Receiver Mode (Separated Triggering)

Remove X5 from iT32 then insert it into a camera hot shoe, iT32 will switch to receiver mode automatically, then off-camera wireless triggering is available via the camera shutter.

  • Flash Mode Switch: Press and hold the < + / M > button of the flash trigger can wirelessly control the flash to switch between TTL auto flash mode and M manual flash mode. The indicator of flash trigger will flash green in TTL auto flash mode, flash orange in M manual flash mode.
  • Output Power Adjustment: Adjust the flash to M manual flash mode, press the < - / > / < + / M > button of the flash trigger can adjust the power from 1/128 to 1/1 with ±1/3 increment each step.
  • FEC Amount Adjustment: Adjust the flash to TTL auto flash mode, press the < - / > / < + / M > button of the flash trigger can adjust the FEC amount from -3.0 to +3.0 with ±1/3 increment each step.

Sync Triggering Godox Flashes

When iT32 and X5 are separated, X5 can also sync trigger other Godox flashes.

Take AD100ProII as an example:

  1. Remove X5 from iT32, iT32 will switch to receiver mode automatically.
  2. Power off the camera, insert X5 into the camera hot shoe and power it on.
  3. Set AD100ProII: Press the MENU button to enter menu interface, rotate and press the SET dial to select and enter wireless settings, set the group, channel, ID to the same as iT32.
  4. Press the camera shutter to sync trigger iT32 and AD100PROII.

Note: Group A supports triggering, output power and FEC amount adjustment, other groups only support triggering.

High-speed Sync

High speed sync (FP flash) enables the flash to synchronize with all camera shutter speeds. This is convenient when you want to use aperture priority for fill-flash portraits.

  • Touch Screen: Slide the screen top-down to enter menu interface, click the < 4H / > icon to choose < 4H > and enter high-speed sync mode.
  • Buttons and Select Dial: Press the MENU button to enter menu interface, rotate the select dial to choose the < 4H / > icon, then press the SET button to switch to < 4H > and enter high-speed sync mode.

Note:

  1. The minimal flash power is 1/16 in HSS mode.
  2. Choose HSS mode in camera settings for iT32+X5F.
  3. When using Nikon camera with iT32+X5N, the HSS is on by default in high-speed camera shutter, while HSS is off in low-speed shutter.

Second-curtain Sync

With a slow shutter speed and second-curtain sync, you can create a light train following the subject. The flash fires right before the shutter closes.

  • Touch Screen: Slide the screen top-down to enter menu interface, click the < 4H / / > icon to choose < > and enter second-curtain sync mode.
  • Buttons and Select Dial: Press the MENU button to enter menu interface, rotate the select dial to choose the < 4H / / > icon, then press the SET button to switch to < > and enter second-curtain sync mode.

Note:

  1. Choose < REAR > REAR flash mode in the settings of Sony camera for iT32+X5S.
  2. Choose MENU>Flash Light Function Setting>REAR < REAR > flash mode on Fujifilm cameras for iT32+X5F.
  3. For iT32+X5N, press < > button on Nikon camera, rotate the dial until the < REAR > appears on the control panel to enter rear-curtain sync mode, set the camera shutter.
  4. For iT32+X5O, press <OK> button on OM SYSTEM camera or <MENU> button on Panasonic camera to enter rear curtain sync mode setting. When the < > appears on the display, set the camera shutter.

First-curtain Sync

With a first-curtain sync, you can create a light train leading the subject. The flash fires when the shutter starts.

  • Touch Screen: Slide the screen top-down to enter menu interface, click the < 4H / / > icon to choose < > and enter first-curtain sync mode.
  • Buttons and Select Dial: Press the MENU button to enter menu interface, rotate the select dial to choose the < 4H / / > icon, then press the SET button to switch to < > and enter first-curtain sync mode.

Note: Please refer to the second-curtain sync section above for the settings of different cameras.

Modeling Lamp

  • Touch Screen: Slide the screen top-down to enter menu interface, click the < > icon to enter modeling lamp settings, in which you can turn on or off the modeling lamp. Pull the progress bar to adjust its brightness from level 1 to level 10.
  • Buttons and Select Dial: Press the MENU button to enter menu interface, rotate the select dial to choose the < > icon, then press the SET button to enter modeling lamp settings, press the SET button again can turn on or off the modeling lamp. Rotate the select dial to choose the progress bar, then press the SET button and rotate the select dial can adjust its brightness from level 1 to level 10.

Screen Lock

  • Touch Screen: Slide the screen top-down to enter menu interface, click the < > icon to turn on the screen lock function. Press and hold the SET button for 2s to unlock.
  • Buttons and Select Dial: Press the MENU button to enter menu interface, rotate the select dial to choose the < > icon, then press the SET button to turn on the screen lock function. Press and hold the SET button for 2s to unlock.

Wireless Settings

The wireless sync function helps the sender and receiver to quickly set the same channel and ID.

  • Touch Screen: Slide the screen top-down to enter menu interface, click the < ( (p) > icon to enter wireless settings.
  • Buttons and Select Dial: Press the MENU button to enter menu interface, rotate the select dial to choose the < ( (p) > icon, then press the SET button to enter wireless settings.

Channel Settings

If there are other wireless flash systems nearby, you can change the wireless channels to prevent signal interference. The wireless channels (01-32) of the sender unit and the receiver unit(s) must be set to the same.

  • Touch Screen: Slide the "Channel" box to choose your desired channel.
  • Buttons and Select Dial: Rotate the select dial to choose "Channel" box, then press the SET button to enter channel settings, rotate the select dial and press the SET button to choose your desired channel.

ID Settings

Change the wireless ID to avoid interference for it can only be triggered after the wireless IDs (OFF/01-99) of the sender unit and the receiver unit are set to the same.

  • Touch Screen: Slide the "ID" box to turn off the ID, or choose your desired ID.
  • Buttons and Select Dial: Rotate the select dial to choose "ID" box, then press the SET button to enter ID settings, rotate the select dial and press the SET button to choose your desired ID.

Wireless Sync

The wireless sync function helps the sender and receiver to quickly set the same channel and ID.

Note: Wireless sync function is only available in sender mode and receiver mode.

  • Receiver Wireless Sync:
    1. Set iT32+X5 to sender mode, details of which please refer to the sender mode above.
    2. Assume retro camera flash Lux Master as the receiver.
    • Touch Screen: Click the "SYNC" icon on both iT32 and Lux Master.
    • Buttons and Select Dial: Rotate the select dial on iT32 to choose "SYNC" icon, then press the SET button. Rotate the select dial on Lux Master to choose "SYNC" icon, then press the SET button.
  • Sender Wireless Sync:
    1. Set iT32+X5 to receiver mode, details of which please refer to the receiver mode above.
    2. Assume flash trigger X3 as the sender.
    • Touch Screen: Click the "SYNC" icon on both iT32 and X3.
    • Buttons and Select Dial: Rotate the select dial on iT32 to choose "SYNC" icon, then press the SET button. Rotate the select dial on X3 to choose "SYNC icon, then press the select dial.
  • iT32+X5 Wireless Sync: When the sender unit and receiver unit are both iT32+X5, wireless sync is also available.

Custom Function Settings

Users can set the parameters of the following custom functions.

IconFunctionOptionsDescription
Trigger Dist0-30mFor extremely close distance triggering in a range from 0 to 30m (in sender mode)
1-100mFor far distance triggering in a range from 1m to 100m (in sender mode)
Sender Flash (only available in iT32+X5C)OnSender flash off
OffSender flash on
PhotocellOFFTurn off photocell
S1The flash will fire synchronously when the main flash fires, only available in M manual flash mode.
S2The flash will ignore a single "pre-flash" from the main flash and will only fire in response to the second, actual flash from the main flash, only available in M manual flash mode.
TCMOnFlash value of TTL mode can be converted to the power value of M mode (only available in wi-off mode)
OffTurn off this function
StandbyOnAutomatically standby after the set time (90 seconds) of idle use, and auto power off after 8 hours of idle use.
OffDo not automatically standby after the set time (90 seconds) of idle use.
Auto OffOffTurn off auto power off function
30 minThe flash will automatically shut down after 30 minutes of idle use.
60 minThe flash will automatically shut down after 60 minutes of idle use.
90 minThe flash will automatically shut down after 90 minutes of idle use.

Wireless Flash Shooting (2.4G Wireless Transmission)

This chapter mainly explains how to perform wireless multiple shooting with 2.4G wireless transmission by using iT32+X5 as the sender unit (refer to as "sender unit" below) and Godox flashes with 2.4G wireless receiving function as the receiver unit (refer to as “receiver unit” below).

As a sender unit, iT32+X5 can control various receiver units with Godox wireless X system such as AD100Pro II, AD200Pro II, AD600Pro II, AD600BM II, iT32, iT30Pro, V100, V480 and Lux Master.

Note:

  1. The channel, group, and ID of the sender and receiver units should be set to the same, details of which please refer to the wireless settings section above.
  2. The above listed are only popular models that can be controlled by iT32+X5, please refer to the official website for more controllable models.

TTL: Wireless Multiple Flash Shooting in TTL Auto Flash Mode

Set the flash groups (A, B and C) of iT32+X5 (sender unit) as <TTL>, either the same or different FEB value, no need to set the receiver units and they will perform wireless multiple flash shooting in auto flash.

Diagram showing TTL wireless multiple flash shooting setup.
Figure 5.3: TTL Auto Flash Shooting with Multiple Receiver Units - Illustration of a sender unit controlling multiple receiver units in TTL mode.

M: Wireless Multiple Flash Shooting in M Manual Flash Mode

Set the flash groups (A, B and C) of iT32+X5 (sender unit) as <M>, either the same or different flash output power, no need to set the receiver units and they will perform wireless multiple flash shooting by following the sender.

Wireless Multiple Flash Shooting in Different Flash Modes

Set the flash groups (A, B and C) of iT32+X5 (sender unit) as the different flash modes, no need to set the receiver units and they will perform wireless multiple flash shooting in different flash modes.

Control with the Camera's Menu (only available in iT32+X5C)

If the camera flash is attached to an EOS camera which has a camera control function, the flash can be controlled using the camera's menu screen.

The functions that can be set are as follows. The available settings vary depending on the flash mode, wireless flash function settings, and other conditions.

FunctionSettings
Flash FiringOn/Off
E-TTL BalanceAmbience priority/Standard/Flash priority
TTL MeteringEvaluative (Face priority) / Evaluative / Average
Continuous Flash ControlE-TTL shooting every time / E-TTL shooting for the first time
Flash ModeTTL flash metering (auto flash) /manual flash/multi flash (stroboscopic)
Wireless FunctionsWireless flash: Off/Radio transmission
Shutter SyncFirst-curtain Sync/Second-curtain Sync/High-speed Sync
Flash Exposure CompensationAdjustable

Global Shutter Sync Shooting (only available in iT32+X5S)

By using a combination of iT32+X5S and a camera equipped with global shutter image sensor, flash photography can be synchronized with the entire range of shutter speeds available on the camera, enabling more effective flash exposures than conventional high-speed sync photography (HSS).

  1. When iT32+X5S is used in TTL auto flash mode with a global shutter camera, the flash will be synchronized properly at both low and high shutter speeds. Compared to a non-global shutter camera, with a global shutter camera, the HSS flash time is shorter (about 2-5 milliseconds), the recycle time is faster, and the camera can take more shots.
  2. When iT32+X5S is used in M (manual) flash mode and you want to use single pulse flash (not HSS) in high-speed shutter (with a shutter speed faster than 1/600), you can adjust the camera's flash delay time to match the exposure time, so that you can shoot with a more appropriate amount of light. Compared to HSS mode, this mode has a better flash index with the same power.

Flash timing settings: Camera Menu → (Exposure/Color) → [Flash] → [Flash Timing Setting] → [On] → Set the flash timing to the desired value.

ADJ flash timing settings menu:

  • On: Adjusts the flash timing manually (0 microseconds to 1000 microseconds).
  • Off: Does not adjust the flash timing (the flash will fire in non-single pulse flash when the shutter speed is 1/600).

How to Match the Flash and the Shutter

High-speed shutter single pulse flash requires very strict time alignment. As shown in the figure, the shutter needs to be turned on at the optimal light effect of the flash. Matching method is as follows:

Set the flash to M (manual) flash mode and enter the menu, turn on ADJ in the camera flash timing settings. Input ADJ parameter which is related to the camera and flash used. If you are using iT32+X5S with A9MIII, this parameter is about 140 microseconds when iT32+X5S is wireless off, and about 540 microseconds when iT32+X5S is wireless on (if you are using other global shutter cameras, you need to full-time match to determine the time). After setting the above parameters, adjust the camera shutter to 1/80000 and the flash power to 1/128 (The matching requirements are higher for faster shutter speed and lower power, if you adjust the right combination, other combinations are usually suitable. When set to a fast shutter speed and high power, since the flash timing is much longer than the shutter time, you can move the time back and select the peak of the flash.), you can finetune the ADJ parameters to the optimal exposure time in case the flash is out of sync, then you can test the shootings under other shutters.

Flash power curve diagram showing flash amount, time, shutter speed, and flash starting timing.
Figure 5.4: Flash Power Curve - Illustrates the relationship between flash amount, time, shutter speed, and flash starting timing.

Note:

  1. If you set the camera's shutter speed to faster than 1/10000 and take a picture, the brightness and color may vary.
  2. For camera equipped with a global shutter image sensor, the HSS icon will not be displayed on the panel regardless of whether the high-speed sync setting is [ON] or [OFF].
  3. When the flash is connected to the camera using a sync cord, the camera shoots with a traditional high-speed sync instead of using the global shutter sync, so the distance that the flash's light can reach is shortened.

Sync Triggering

Insert a sync cord or trigger plug here into the sync cord jack, the flash will be fired synchronously with the camera shutter.

Over-Temperature Protection

  • To avoid overheating and deteriorating the flash head, do not fire more than the mentioned below continuous flashes in fast succession at 1/1 full power, or fire more than 40 continuous flashes in fast succession at 1/1 full power in HSS mode.
  • If you fire more than the mentioned below continuous flashes and then fire more flashes in short intervals, the inner over-temperature protection function may be activated and make the recycle time over 10 seconds. If this occurs, allow a rest time of about 10 minutes, and the flash unit will then return to normal.
  • When the over-temperature protection is started, < > is shown on the display.

Number of flashes that will activate over-temperature protection:

Power Output LevelNumber of Flashes
1/140
1/260
1/4120
1/8200
1/16300
1/32600
1/641200
1/1282000

Number of flashes that will activate over-temperature protection in HSS mode:

Power Output LevelNumber of Flashes
1/140
1/275
1/4100

6. Maintenance

Clean the device gently with a dry cloth. Do not use a wet cloth as it may damage the device.

7. Troubleshooting

If there is a problem, refer to this troubleshooting guide.

The camera flash does not fire.

  • Attach the camera's mounting foot securely to the camera.
  • If the electrical contacts of the camera flash and camera are dirty, clean the contacts with dry cloth.
  • If the < > or < 4H > is not displayed in the view finder of camera. Wait until the flash is fully recycled and the flash ready indicator lights up.
  • If the flash ready indicator does not light up after a long wait, check whether the battery power is enough. If the battery power is low, please replace or charge the battery immediately.

The power turns off by itself.

  • Setting as wi-off/sender mode when the standby function is on, the flash will enter sleep mode automatically after 90 seconds of idle use. Press the camera shutter halfway or press any button will wake up the flash unit.
  • Setting as wi-off/sender mode when the standby function is off while the auto off function is on, the flash will automatically shut down after 60 minutes (or 30 minutes, 90 minutes) of idle use. Restart the flash unit.
  • Setting as receiver mode when the auto off function is on, the flash will automatically shut down after 60 minutes (or 30 minutes, 90 minutes) of idle use. Restart the flash unit.

The flash exposure is underexposed or overexposed.

  • You used high-speed sync. With high-speed sync, the effective flash range will be shorter. Make sure the subject is within the effective flash range displayed.
  • The subject appears too dark or too bright. Set the proper FEC value.

The Reason & Solution of Not Triggering in Godox 2.4G Wireless

  1. Disturbed by the 2.4G signal in outer environment (e.g. wireless base station, 2.4G wifi router, Bluetooth, etc.)
    → To adjust the channel CH setting on the flash trigger (add 10+ channels) and use the channel which is not disturbed. Or turn off the other 2.4G equipment in working.
  2. Please make sure that whether the flash has finished its recycle or caught up with the continuous shooting speed or not (the flash ready indicator is lightened) and the flash is not under the state of over-heat protection or other abnormal situations.
    → Please downgrade the flash power output. If the flash is in TTL mode, please try to change it to M mode (a pre-flash is needed in TTL mode).
  3. Whether the distance between the flash trigger and the flash is too close or not (<0.5m).
    → Please turn on the “close distance wireless mode". Set the triggering distance to 0-30m.
  4. Whether the flash trigger and the receiver end equipment are in the low battery states or not
    → Please replace the battery or charge it in time.
  5. The flash trigger's firmware is an older version
    → Please upgrade the firmware of the flash trigger referring to the instruction manual for specific firmware upgrades.
  6. The camera's firmware is an older version
    → Please upgrade the firmware of the camera referring to its instruction manual.

8. Specifications

ModeliT32+X5SiT32+X5C/N/O/F
Global Shutter Sync ShootingProvidedUnprovided
Radio Wireless Global Shutter SyncProvidedUnprovided
Guide Number (1/1 step)Approx. GN18 (ISO 100, in meters)
Flash Duration (t0.1)1/1000s ~ 1/30000s
Exposure Control
Exposure Control SystemTTL auto flash and manual flash
Flash Exposure Compensation (FEC)±3 steps with 1/3 increment each step
Sync ModeHigh-speed sync (up to 1/8000 seconds, or 1/80000 seconds with Sony cameras equipped with global shutter), first-curtain sync, and second-curtain sync
Multi FlashProvided (up to 100 times, 100Hz)
Wireless Flash (Radio 2.4G Transmission)
Wireless FunctionSender, Receiver
Sender GroupsM, A, B, C (iT32+X5S/N/F/O)A, B, C, D (iT32+X5C)
Receiver GroupsA, B, C, D
Transmission Range (approx.)Max. 80m (Max. 20m in separated triggering)
Channels32: 1-32
IDOFF/1-99
Power Supply
Lithium BatteryiT32: 7.4V/900mAh; X5: 3.8V/100mAh
Recycle Time (1/1 step)Approx. 1.5s
Number of Flashes (1/1 step)Approx. 510
Power SavingProvide standby and auto off functions
Sync Triggering ModeHot shoe, 2.5mm sync cord
Dimension and Net Weight
DimensioniT32: 56*39*101mmX5: 32*32*27mm
Net WeightiT32: 169gX5: 23g

Specifications and data may subject to changes without notice.

9. Firmware Upgrade

  • This product supports firmware upgrade through the USB-C port, please use a USB-C cable (sold separately).
  • As the firmware upgrade needs the support of Godox G3 V2.0 software, please download and install the "Godox G3 V2.0 firmware upgrade software" before upgrading. Then, choose the related firmware file.
  • Press the MENU button and insert into the USB-C port for upgrade.
  • Please refer to the latest electronic version of the instruction manual.
  • The download website of firmware upgrade is: https://www.godox.com.cn/firmware-G3/

10. Compatible Camera Models

iT32+X5C can be used on the following Canon camera models:

80D, 90D, 7D, 6D, 70D, 750D, 760D, 5DMarkIV, EOS 1DX, 6DMarkII, 77D, 800D, 5DMarkIII, 5DMarkII, 60D, 7D MarkII, 600D, 50D, 30D, 40D, 500D, M5, M3, M50, R, RP, M6II, R5, 1500D, 3000D, R7, R6II, R50, R8, R5C, R10, R100, R5II, R3, 200DII

iT32+X5S can be used on the following Sony camera models:

a77II, a99, a77, DSC-RX10, a6000, a7R, a350, a7RII(4.0), a7RIII, a7M3, a9, a7RIV, α7R5, a7MIV, ZV-E10, A9III, A7C, A7CII, a6400, a6500

iT32+X5N can be used on the following Nikon camera models:

D800, D750, D700, D610, D500, D200, D300S, D5, D4, D810, D780, D5300, D5200, D5100, D5000, D3300, D3100, D60, Z6, Z7II, Z8, ZFC

iT32+X5O can be used on the following OM SYSTEM or Panasonic camera models:

OM SYSTEM: E-M1, PEN-F, E-M10II, E-PL8, E-P5, E-M10III
Panasonic: GH4, LX100, DMC-GF1, DMC-G85, DMC-GX85, DMC-LX100, DMC-FZ2500GK, S1

iT32+X5F can be used on the following Fujifilm camera models:

A: X-Pro2, X-T20, X-T2, X-T1, GFX50s, GFX50R, X-T30, X-T4, X-T3, X-S2O, X-T5
B: X-Pro1, X-T10, X-E1, X-A3
C: X100F, X100T

Compatible camera models & functions support

CameraCamera Flash
TTL FlashM Manual FlashMulti Flash
FrontRearHSSFrontRearHSS
A√√√√√√√
B√√--√----√
C√√--√√--√
Camera2.4G Wireless Control
TTL FlashM Manual FlashMulti Flash
FrontRearHSSFrontRearHSS
A√√√√√√√
B√√--√----√
C√√--√√--√

Note: X100T do not have second curtain sync (REAR) function.

Note:

  1. These tables only list the tested camera models, not all cameras. For the compatibility of other camera models, a self-test is recommended.
  2. Rights to modify these tables are retained.

11. User Tips

  • Portability: Users appreciate the lightweight and compact design, making it ideal for travel and easy to carry in a camera bag.
  • Versatility: The detachable X5 trigger offers flexible lighting options, allowing for both on-camera and off-camera use.
  • Indoor Use: Effective for indoor photography to prevent high ISO settings and improve image quality.
  • Quick Charging: The flash charges quickly, even when taking multiple pictures in a row.
  • Compatibility: Ensure to select the correct X5 trigger version (e.g., X5C for Canon, X5S for Sony, X5N for Nikon, X5F for Fujifilm, X5O for Olympus/Panasonic) for proper camera compatibility.
  • Magnetic Accessories: The magnetic mounting system and accessories (like color gels) are praised for unlocking creative lighting possibilities.

12. Frequently Asked Questions (FAQ)

Q: Which X5 trigger is compatible with my Canon T5, T6i, and RP?
A: You should choose the X5C version for compatibility with your Canon cameras.
Q: Is the X5L suitable for Leica Q3?
A: Yes, the X5L is designed for Leica Q3.
Q: Is the iT32 flash suitable for Lumix cameras?
A: Yes, you can choose the X5O version for compatibility with your Lumix camera.
Q: Why is my flash not firing when mounted on my camera?
A: Ensure the flash is securely attached to the hot shoe, clean electrical contacts, check battery level, and verify that the flash is not in sleep mode or overheating. Also, confirm camera compatibility and firmware versions.
Q: How can I prevent overheating during continuous use?
A: Avoid firing more than the recommended number of continuous flashes at full power. If the over-temperature protection activates, allow the flash to cool down for at least 10-15 minutes before resuming use.

13. Warranty & Support

Warranty Period

The warranty period for products and accessories is implemented according to the relevant Product Maintenance Information. The warranty period is calculated from the day (purchase date) when the product is bought for the first time, and the purchase date is considered as the date registered on the warranty card when buying the product.

Product TypeNameMaintenance Period (month)Warranty Service Type
PartsCircuit board12Customer sends the product to designated site
Battery3
Electrical parts e.g. battery charger, etc.12
Other ItemsFlash tube, modeling lamp, lamp body, lamp cover, locking device, package, etc.NoWithout warranty

How to Get the Maintenance Service

If maintenance service is needed, you can directly contact the product distributor or authorized service institutions. You can also contact the Godox after-sale service call and we will offer you service. When applying for maintenance service, you should provide a valid warranty card. If you cannot provide a valid warranty card, we may offer you maintenance service once confirmed that the product or accessory is involved in the maintenance scope, but that shall not be considered as our obligation.

Inapplicable Cases

The guarantee and service offered by this document are not applicable in the following cases:

  1. The product or accessory has expired its warranty period;
  2. Breakage or damage caused by inappropriate usage, maintenance or preservation, such as improper packing, improper usage, improper plugging in/out external equipment, falling off or squeezing by external force, contacting or exposing to improper temperature, solvent, acid, base, flooding and damp environments, etc;
  3. Breakage or damage caused by non-authorized institution or staff in the process of installation, maintenance, alternation, addition and detachment;
  4. The original identifying information of product or accessory is modified, alternated, or removed;
  5. No valid warranty card;
  6. Breakage or damage caused by using illegally authorized, nonstandard or non-public released software;
  7. Breakage or damage caused by force majeure or accident;
  8. Breakage or damage that could not be attributed to the product itself.

Once any of these situations are met, you should seek solutions from the related responsible parties and Godox assumes no responsibility. The damage caused by parts, accessories and software that beyond the warranty period or scope is not included in our maintenance scope. The normal discoloration, abrasion and consumption are not the breakage within the maintenance scope.

Godox After-sale Service Call: +86-755-29609320 (8062)

For the full user manual in PDF format, please refer to the official PDF document.

© 2023 Godox. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.