MOES ZS-FB-V3

Contents

MOES Tuya ZigBee Fingerbot Plus User Manual

Model: ZS-FB-V3

1. Product Introduction

The MOES Tuya ZigBee Fingerbot Plus is the world's smallest robot designed for smartly controlling various types of traditional buttons and switches. It transforms your existing home appliances into smart devices through robotic clicks. With the Fingerbot Plus, you can switch lights, schedule coffee making, activate your vacuum cleaner with voice commands, and remotely power on your office PC, making home automation effortless.

MOES ZigBee Smart Fingerbot Plus device
Figure 1: MOES ZigBee Smart Fingerbot Plus
Diagram showing Fingerbot and its replaceable arm
Figure 2: Fingerbot Plus with Replaceable Arm

2. Important Safety Information

CAUTION!

Before beginning installation or use, please read this guide and any other accompanying documents carefully and entirely. Failure to follow installation procedures could lead to malfunction, danger to your health and life, violation of law, or refusal of legal and/or commercial guarantee. MOES is not responsible for any loss or damage in case of incorrect installation or improper operation of this device due to failure to follow the user and safety instructions in this guide.

2.1. Warnings

  • The product is non-waterproof. Do not install it on an underwater appliance.
  • The product contains a lithium battery; therefore, it is prohibited in humid, high-temperature environments.
  • Do not hinder the movement of the Fingerbot's arm when it is working. Otherwise, it may cause the arm to fall off and damage the motor inside the Fingerbot.

2.2. Battery Safety Warnings

⚠ WARNING

INGESTION HAZARD: This product contains a button cell or coin battery.

DEATH or serious injury can occur if ingested. A swallowed button cell or coin battery can cause Internal Chemical Burns in as little as 2 hours. KEEP new and used batteries OUT OF REACH of CHILDREN. Seek immediate medical attention if a battery is suspected to be swallowed or inserted inside any part of the body.

  • Remove and immediately recycle or dispose of used batteries according to local regulations and keep away from children. Do NOT dispose of batteries in household trash or incinerate.
  • Even used batteries may cause severe injury or death.
  • Call a local poison control center for treatment information.
  • The battery type is CR2, and the battery voltage is 3V.
  • Non-rechargeable batteries are not to be recharged.
  • Do not force discharge, recharge, disassemble, heat above 60°C, or incinerate. Doing so may result in injury due to venting, leakage, or explosion resulting in chemical burns.
  • Ensure that the battery is correctly loaded into the battery compartment according to the polarity marked, and the positive and negative poles cannot be installed reversely.
  • Do not mix old and new batteries, different brands, or types of batteries, such as alkaline, carbon-zinc, or rechargeable batteries.
  • Remove and immediately recycle or dispose of batteries from equipment not used for an extended period of time according to local regulations.
  • Always completely secure the battery compartment. If the battery compartment does not close securely, stop using the product, remove the batteries, and keep them away from children.

3. Setup and Installation

3.1. Unboxing and Initial Device Preparation

Upon receiving your Fingerbot Plus, carefully unbox the device. The first step is to prepare the device for pairing.

Video 1: Unboxing and Initial Setup of MOES ZigBee Fingerbot Plus.

  1. Open the back cover of the Fingerbot Plus.
  2. Remove the insulation paper from the battery compartment.
  3. Long press the reset button (located near the battery) for 5 seconds until the indicator light flashes. This puts the device into pairing mode.
Fingerbot Plus with battery compartment open, showing reset button and battery
Figure 3: Battery and Reset Button Location

3.2. App Installation and Device Pairing

The Fingerbot Plus works with the MOES App. Ensure you have a ZigBee Cable Gateway for full functionality.

  1. Download the "MOES" App from the Google Play Store or Apple App Store.

    QR code for MOES App download Google Play and App Store logos

    Figure 4: MOES App Download QR Code and App Store Links

  2. Register or log in to your MOES account.
  3. Ensure your MOES App is successfully connected to a ZigBee Cable Gateway.
  4. On the "Multimode gateway" page in the MOES App, click "add device".
  5. The app will discover nearby devices. Once the Fingerbot Plus is found and added successfully, you can edit its name.
  6. Click "Done" to enter the device page and begin using your smart home automation.
Screenshot of MOES App showing Fingerbot added to gateway
Figure 5: Fingerbot with Gateway and App Control Interface

3.3. Physical Installation of Fingerbot Plus

To ensure optimal performance and adhesion, follow these steps for physical installation:

  1. Clean the surface of the button or switch panel where you intend to install the Fingerbot Plus.
  2. Attach the Fingerbot Plus to the panel using the double-sided tape provided in the package.
  3. After installation, connect your Fingerbot with the App and calibrate the movement of its robotic arm to fit your specific switches and buttons.
  4. For maximum adhesion, it is recommended to let the Fingerbot rest for 24 hours after installation before heavy use.
Fingerbot Plus being manually pressed on a light switch
Figure 6: Fingerbot Plus on a light switch, demonstrating manual touch control.

4. Operating the Fingerbot Plus

4.1. Basic Control

  • App Control: You can control the Fingerbot directly via Bluetooth using the MOES App.
  • Manual Control: The Fingerbot Plus features a touch button on the device itself, allowing for manual ON/OFF control of the robotic arm.
Comparison of Fingerbot (App only) and Fingerbot Plus (App and Touchpad)
Figure 7: Fingerbot Plus offers both App and Touchpad control.

4.2. Advanced Control Features

  • Scheduler: Set schedules in the App to automatically activate the Fingerbot at specific times (e.g., 7:00 AM ON / 5:30 PM OFF for curtains). A ZigBee hub is required for timing schedules.
  • Remote Control: With a Fingerbot Bridge (purchased separately), you can control your Fingerbot through the Internet from anywhere.
  • Voice Control: With a Fingerbot Bridge, you can connect Fingerbot with voice assistants such as Google Home Assistant and Amazon Alexa. Set up voice commands in the App to activate voice-control functions.
Fingerbot Plus with Alexa and Google Home logos, showing voice command example
Figure 8: Voice Control with Alexa and Google Home.
Fingerbot Plus controlling a traditional curtain switch with a scheduled timer
Figure 9: Timer your schedule for automatic ON/OFF. Note: The ZigBee hub is a must for timing schedule.
Fingerbot Plus turning on a floor cleaning robot remotely
Figure 10: Smartly turn on your house floor cleaning robot outdoors in Smart Life App. Note: Zigbee gateway is required for wireless control.

4.3. Using Various Tool Arms

The Fingerbot Plus features a modular design, allowing its arm to be replaced with various tool arms to fit different button and switch types.

Fingerbot Plus applied to different types of switches: buttons, rocker switches, and toggle switches
Figure 11: Fingerbot Plus suits 99% scenarios (Available in all kits).
Diagram showing dimensions of Fingerbot Plus and various tool arms
Figure 12: Dimensions of Fingerbot Plus and various tool arms. Note: You need a separate purchase of the fingerbot tool packs.

4.3.1. Straight Arm

We provide three straight arms with different lengths to assist Fingerbot in better fitting various button-control cases. Install the arm by following the picture below.

4.3.2. Rocker Arm

The rocker arm is used to push and pull switch buttons to change the status of equipment. Follow these instructions to install the rocker arm:

  1. After connecting Fingerbot with the App, set Fingerbot to the 'Switch' mode.
  2. Move the arm of Fingerbot to the bottom and fix the Fingerbot on the switch panel.
  3. Tear off the tape covering on the rocker arm to stick the arm to the switch button.
  4. After ensuring firmness, use the App to adjust the rising range of Fingerbot's arm so that its movement range can be adapted to the switch button.
  5. If the app is showing the opposite status to the actual status, please use the 'invert' function to invert the display mode.
Diagram showing installation of rocker arm with 3M tapes
Figure 13: Rocker Arm Installation.

4.3.3. Ring Arm

The ring arm is used to push and pull toggle switches to change the status of equipment. Follow these instructions to install the ring arm:

  1. After connecting Fingerbot with the App, set Fingerbot to the 'Switch' mode.
  2. Following the picture, fix two cushion blocks to Fingerbot with tape.
  3. Put the ring of the arm on the toggle button, and tear off the tape covering on the other side of the cushion block to fix the Fingerbot on the switch panel.
  4. After ensuring firmness, use the App to adjust the movement range of Fingerbot's arm so that its movement range can be adapted to the toggle.
Diagram showing installation of ring arm with cushion block and 3M tapes
Figure 14: Ring Arm Installation.

4.4. Customizing Control

  • Sustain Time: You can set a "Sustain Time" in the App for more flexible and accurate control, useful for actions requiring a longer press.
  • Touch Control Disable: Disable the Touch Control in the Smart Life APP to avoid misoperations, especially by children.
App screenshot showing sustain time setting for a coffee maker
Figure 15: Set the Sustain Time for More Flexible and Accurate Control.
Child near a fan, with app screenshot showing touch control disabled
Figure 16: Disable the Touch Control in Smart Life APP to Avoid Misoperations by Kids.

5. Maintenance

To ensure the longevity and proper functioning of your Fingerbot Plus, follow these maintenance guidelines:

  • Keep the device clean and free from dust.
  • Avoid exposing the device to extreme temperatures or direct sunlight.
  • Do not attempt to disassemble or repair the device yourself, as this may void the warranty.
  • Regularly check the battery level in the app and replace the CR2 battery when necessary, following the safety warnings in Section 2.2.

6. Troubleshooting

If you encounter problems installing or operating your device, please review its product data sheet for detailed solutions.

For further assistance, you can refer to the product data sheet online: https://www.moestech.com/blogs/news/zs-fb-v3

7. Product Specifications

Feature Specification
Model ZS-FB-V3
Dimensions 34.5 x 34.5 x 34.5 mm
Weight 38g
Communication Protocol ZigBee 3.0
Functionalities App Control, Voice Control, Cloud Control, Scheduler
Stall Torque 2.0 kgf·cm
Working Temperature -10 ~ 55°C / 14°F ~ 131°F
Battery Capacity 500 mAh
Frequency Band 2.4GHz
Maximum Radio Transmit Power +4dbm

8. User Tips

No specific user tips were found in the provided reviews or Q&A content.

9. Warranty and Support

9.1. Warranty Instructions

The product is covered by a 24-month warranty, effective from the date of purchase by a retail customer. To exercise warranty rights, the purchaser must present a warranty card and proof of purchase (VAT invoice, financial receipt, or other document confirming the actual date of purchase).

If product quality problems occur within 24 months from the date of receipt, prepare the product and packaging and go to the place or store where you purchased it to apply for after-sales maintenance. If the product is damaged due to personal reasons, a certain maintenance fee will be charged.

The warranty does not cover:

  • Mechanical damage caused by the user's fault and product defects caused by such damage.
  • Damage caused by improper use of the product.
  • Removal of the warranty seal or serial number from the product.
  • Actions to eliminate physical defects in the product outside of authorized service.
  • Use of non-original parts and consumables.

9.2. Declaration of Conformity

WENZHOU NOVA NEW ENERGY CO.,LTD declares that the radio equipment type ZS-FB-V3 is in compliance with Directive 2014/53/EU, 2014/30/EU, and 2011/65/EU. The full text of the EU declaration of conformity is available at: https://www.moestech.com/blogs/news/zs-fb-v3

9.3. Recycling Information

All products marked with the symbol for separate collection of waste electrical and electronic equipment (WEEE Directive 2012/19/EU) must be disposed of separately from unsorted municipal waste. To protect your health and the environment, this equipment must be disposed of at designated collection points for electrical and electronic equipment designated by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences for the environment and human health. To find out where these collection points are and how they work, contact the installer or your local authority.

WEEE symbol and recycling symbols
Figure 17: Recycling Symbols.

9.4. Contact Information

Manufacturer: WENZHOU NOVA NEW ENERGY CO.,LTD
Address: Power Science and Technology Innovation Center, NO.238, Wei 11 Road, Yueqing Economic Development Zone, Yueqing, Zhejiang, China
Tel: +86-577-57186815
After-sale Service: service@moeshouse.com

EU Representative: AMZLAB GmbH
Address: Laubenhof 23, ESSEN 45326
Email: info@amz-lab.de
Tel: +491745298066

UK Representative: EVATOST CONSULTING LTD
Address: Suite 11, First Floor, Moy Road Business Centre, Taffs Well, Cardiff, Wales, CF15 7QR
Tel: +44-292-1680945
Email: contact@evatost.com

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.