CARABC Sync2 Wireless CarPlay/Android Auto Decoder Box

Contents

CARABC Wireless CarPlay & Android Auto Decoder Box for Ford Sync2

Model: Sync2 Wireless CarPlay/Android Auto Decoder Box

Brand: CARABC

1. Introduction

This manual provides detailed instructions for the installation and operation of the CARABC Wireless CarPlay & Android Auto Decoder Box. This device integrates Apple CarPlay and Android Auto functionalities into your Ford vehicle's existing Sync2 system, enhancing your driving experience with modern smartphone connectivity.

2. Safety Information

  • Ensure the vehicle's ignition is off and the battery is disconnected before beginning any installation to prevent electrical shorts or damage.
  • If you are unsure about any step of the installation process, consult a professional installer.
  • Do not attempt to modify the device or its components, as this may void the warranty and cause damage.
  • Keep the device away from water, moisture, and extreme temperatures.

3. Package Contents

Please check the package for the following items:

  • CarPlay Decoder Box
  • Power Cable
  • CAN Cable
  • USB Cable
  • AUX Cable
  • External Microphone
  • PCB Board
Package contents and decoder box dimensions

Image: Decoder box dimensions (143mm x 98mm x 23mm) and included cables/components.

4. Compatibility

This product is compatible with Ford models equipped with the Sync2 system and an original 8-inch LCD screen. It is not compatible with Sync1 (2007-2012) or Sync3 (2016-2019) systems, or vehicles with non-8-inch screens.

Compatibility table for Ford Sync2 models

Image: Compatibility table showing supported Ford models, Sync2 system, year ranges, and 8-inch LCD screen requirement.

Compatible Ford Models (Sync2 with 8-inch LCD)
ModelSystemYearScreen
FocusSYNC 22012-20158 inch LCD screen
EscapeSYNC 22013-20158 inch LCD screen
FiestaSYNC 22015-20168 inch LCD screen
C-maxSYNC 22013-20158 inch LCD screen
MondeoSYNC 2Various8 inch LCD screen
KugaSYNC 2Various8 inch LCD screen
TaurusSYNC 2Various8 inch LCD screen
EdgeSYNC 2Various8 inch LCD screen
MustangSYNC 2Various8 inch LCD screen
ExplorerSYNC 2Various8 inch LCD screen
Visual compatibility guide for Ford Sync systems

Image: Visual guide showing compatible Sync2 8-inch LCD screens and incompatible Sync3 or smaller screens.

5. Setup and Installation

5.1 Pre-installation Check

  • Verify your car model and year match the compatibility list.
  • Ensure your car dashboard is the same as shown in compatible images.
  • Disconnect the car battery before starting the installation.

5.2 Dial Setup (DIP Switches)

The toggle switches on the decoder box need to be configured based on your vehicle's features. The TF card slot is for software upgrades only.

Smart Link System Dial Setup
Switch No.Function/ConditionSetting (ON/OFF)
1Car has original cameraON
1, 5, 7, 8Manual transmission car with original reversing cameraON
1, 4, 7, 8Automatic transmission car with original reversing cameraON
All othersDefault / Not specifiedOFF

5.3 Installation Videos

For detailed visual guidance on dashboard removal and cable connections, please refer to the official installation videos. Scan the QR codes provided in the original user manual for specific Ford models (F-Series, Kuga, Mondeo) and PCB board installation.

5.4 Cables Connection

Carefully connect all cables as per the provided diagram. Ensure all connections are secure and correctly oriented.

5.5 PCB Board Installation

When installing the PCB board, ensure the letters on the FPC cable are facing upwards. The ribbon cable and slot need to be neat and snapped correctly. It is crucial to mount the new PCB circuit board onto the original FPC circuit board of the car.

5.6 CarPlay Box & Wi-Fi Antenna Placement

  • The CarPlay decoder box can be installed inside the storage box in front of the passenger seat or other suitable, secure locations.
  • The Wi-Fi antenna (integrated into the module) should not be placed close to metal objects, as this can significantly degrade signal quality.

5.7 Microphone Installation

Install the external microphone in a suitable location, such as near the rearview mirror or on the headliner, for optimal voice pickup. Route the cable discreetly.

6. Sound Setup

To ensure audio output from the CarPlay/Android Auto system, follow these steps:

  1. Disconnect Bluetooth: Disconnect or remove any existing Bluetooth connection between your phone and the car's original system.
  2. Connect Audio Cable: Connect the provided AUX cable. If the system automatically returns to the original page, unplug and re-plug the AUX cable into the AUX socket in your car's handlebar box.
  3. Set AV IN: Before using CarPlay/Android Auto, you must set the car's audio input to 'AV IN'.
    1. On your car's Sync2 screen, navigate to the 'Entertainment' interface.
    2. Select 'Entertainment' again.
    3. Select 'A/V In'.

7. Camera Setup

7.1 Original Reverse Camera

If your car has an original reverse camera, ensure DIP switch NO.1 on the decoder box is set to 'ON'.

7.2 Aftermarket Rear Camera

For aftermarket rear cameras, connect the camera's power to the decoder box's designated output. Connect the camera's video signal to the 'REVERSE CAMERA IN' input on the decoder box. Ensure proper grounding (GND 12V-) and connect to the reverse lamp 12V+ signal for automatic activation.

7.3 Aftermarket 360 Camera

For aftermarket 360-degree camera systems, connect the camera's video input to cable NO. 3 ('REVERSE CAMERA IN') and the control signal to cable NO. 9 ('360CAMERA CONTROL') on the decoder box harness.

8. Operating Instructions

8.1 System Switching

To switch between the original Sync2 system and the CarPlay/Android Auto system:

  • Long-press the 'previous' or 'next' button on your steering wheel for 2 seconds.
  • Alternatively, long-press the 'OK' or 'Sound' button on your car's console (if available).

8.2 Wireless CarPlay / Android Auto

  1. Disconnect or remove any existing Bluetooth connection between your phone and the car's original system.
  2. Turn on Wi-Fi on your mobile phone.
  3. Turn on Bluetooth on your mobile phone.
  4. On your phone, search for the product's Bluetooth device, which will appear as 'Car Audio_XXXX'.
  5. Pair your phone with 'Car Audio_XXXX'.
  6. Allow any sync requests on your phone.
  7. The system will automatically connect to CarPlay or Android Auto.

8.3 Wired CarPlay / Android Auto

  1. Connect your mobile phone to the decoder box using a USB cable.
  2. The system will automatically activate wired CarPlay or Android Auto.

8.4 Wireless AirPlay (for iPhone)

  1. If CarPlay is active, disconnect it by turning off your iPhone's Wi-Fi.
  2. On the decoder box interface, click the 'Mirroring' icon. The hotspot name and password will be displayed.
  3. Select 'iPhone' on the mirroring interface.
  4. On your iPhone, connect to the Wi-Fi network named 'CarPlay_XXXX' (as displayed on the screen). The password is '88888888'. (Only required for the first connection).
  5. Open your iPhone's Control Center, select 'Screen Mirroring', and choose the displayed device to start AirPlay.

8.5 Wireless Android Mirroring

  1. Download and install the 'M-link' app on your Android phone.
  2. If CarPlay/Android Auto is active, disconnect it.
  3. On the decoder box interface, click the 'Mirroring' icon.
  4. Select 'Android' on the mirroring interface.
  5. Turn on Bluetooth on your Android phone, search for 'Car Audio_XXXX', and pair.
  6. On your Android phone, go to 'Mobile network' settings > 'Tethering & personal hotspot' > 'Portable WLAN hotspot'.
  7. Configure the WLAN hotspot: Set the hotspot name and password to be consistent with what is shown on the decoder box's 'Mirroring' interface.
  8. In the hotspot settings, select 'Show advanced options' and choose '5.0 GHz Band'.
  9. Turn on the 'Personal Hotspot' on your phone, then open the 'M-link' app to initiate mirroring.

9. Troubleshooting (FAQ)

  • Q: Car screen touch does not work after installation?
    A: This is usually caused by reverse installation of the FPC touch cable. Ensure the letters on the cable are facing upwards during installation.
  • Q: No sound after installation?
    A: Check if the AUX cable is installed correctly and if the car's audio input is set to AUX mode. Also, delete any previous Bluetooth connections between your mobile phone and the car.
  • Q: No touch on the screen after installation?
    A: Check the small FPC cable connection; ensure the letters are on the front side for correct installation.
  • Q: Reverse camera does not show after installation?
    A: Check the DIP switch settings. For original cameras, switch 1 should be ON. For automatic gear cars, switches 1, 4, 7, 8 should be ON. For manual gear cars, switches 1, 5, 7, 8 should be ON.
  • Q: How to connect wireless CarPlay/Android Auto?
    A: Your mobile phone only needs to connect to the decoder box's Bluetooth. Ensure your phone's Bluetooth is in an idle state (not connected to other devices like a watch recorder). Connecting via Bluetooth will automatically initiate Wi-Fi transmission; you cannot manually enter the Wi-Fi password.

10. Specifications

  • Dimensions: 143mm (Length) x 98mm (Width) x 23mm (Height)
  • Connectivity: Wireless CarPlay, Wireless Android Auto, Wired CarPlay, Wired Android Auto, AirPlay, Android Mirroring
  • Camera Support: Original Reverse Camera, Aftermarket Rear Camera, Aftermarket 360 Camera
  • System Compatibility: Ford Sync2 with 8-inch LCD screen

11. User Tips

  • For manual transmission Ford models with a reversing camera, ensure DIP switch 5 is set to 'ON' for proper camera functionality, in addition to other required switches.
  • Always double-check cable connections and DIP switch settings if you encounter unexpected behavior.

12. Warranty and Support

This product comes with a manufacturer's warranty. For warranty claims, technical support, or any inquiries, please contact CARABC customer service.

Contact Information:

  • WhatsApp: +8618923410098
  • E-mail: 5660103@qq.com

Please have your product model and purchase details ready when contacting support.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.