1. Product Overview
The HT-BCT50A lithium battery capacity tester is designed for battery cells within a voltage range of 0.3-5V and capacities from 1-2000Ah. This device offers high accuracy (±0.001A/V) and integrates functions for battery capacity testing, charging, discharging, and setting work steps via a connected computer. It precisely collects real-time battery voltage signals, stores data, and processes operations, ensuring high precision, timely results, simple operation, and reliable performance.
Figure 1: Heltec HT-BCT50A Battery Tester and its accessories, including cables, manual, and packaging.
2. Product Features
- Automatically collects battery voltage for analysis and continuously outputs a constant current.
- Software control via computer connection for convenient and efficient operation.
- Adjustable current with a peak value of up to 50A.
- Built-in charging system for integrated control of charging and discharging.
- Simplified operation interface, supporting both Chinese and English languages.
3. Safety Precautions and Important Reminders
WARNING: Improper use can lead to battery damage, explosion, or fire. Always follow instructions carefully.
- When setting parameters, select voltage settings that match your battery type (e.g., Ternary lithium battery 2.8V; lithium iron phosphate battery 2.5V). Incorrect settings can damage the battery.
- Do not test batteries with a voltage exceeding 5V.
- Do not connect batteries in reverse; reverse connection voids warranty.
- If a battery cell overheats or voltage fluctuates rapidly, it indicates excessive current, poor contact, or high internal resistance.
- Do not test batteries without a protection board, non-rechargeable batteries, zero-voltage batteries, or swollen/damaged batteries.
- For lithium battery packs with port protection boards, charging must be done through the charging port and discharging through the discharging port. Cycle mode is strictly prohibited.
- The radiator surface can reach high temperatures and is connected to the battery's positive terminal. Avoid short-circuiting or touching.
- Set charging and discharging cut-off voltages/currents correctly and reasonably.
- Conduct tests in an open, supervised environment, away from high-temperature, flammable, explosive, or valuable items.
- Use a well-grounded socket to prevent leakage or induced electricity.
- For batteries with capacity less than 10AH, set charging current ≤ 5A.
- Use only compatible battery clamps and connection wires. Do not extend or modify them.
- Monitor the instrument and battery during charging/discharging. Do not leave unattended.
- Do not disassemble or modify the capacity tester.
- Prevent water or mist from entering the instrument.
- Data will not be recorded if operation lasts less than 2 minutes.
4. Setup
4.1 Unpacking and Product List
Carefully unpack the HT-BCT50A Battery Pack Capacity Tester and verify all components are present.
Figure 2: HT-BCT50A Tester securely packaged in foam.
The product package typically includes:
- HT-BCT50A Tester Unit
- Testing Clips (Red and Black)
- Testing Fixture (optional accessory)
- Power Cord
- USB Data Wire
- User Manual
Figure 3: Specialized connection cable with two connectors.
4.2 Physical Connections
Familiarize yourself with the ports and controls on the tester unit.
- Power Cord Interface: Connect the provided power cord to the back of the machine.
- Data Transmission Interface: Connect the USB data wire to this port on the side of the machine for communication with a computer.
- Battery Connection Terminals: Located on the front panel. The positive terminal (red) and negative terminal (black) are clearly marked. Ensure correct polarity.
Figure 4: Front panel of the HT-BCT50A, showing the display, control knob, start/stop button, and battery connection terminals.
Critical Connection Guidelines:
- Both small and large alligator clips must be clamped onto the battery tabs. The small clip is for voltage sampling, and the large clip is for over-current.
- Ensure sufficient contact area between the large crocodile clamp and the battery tab. Do not clamp screws, nickel sheets, or wires, as this can cause overheating, damage, or testing interruption.
- The small crocodile clip must be clamped at the root of the battery terminals for accurate voltage sampling and capacity testing.
4.3 Software Installation and Connection
- Find and open the installation software (downloadable via QR code in the manual or from customer service).
- Choose an installation location (avoid C drive if possible).
- After installation, run the software for the first time and select the network (check public network if firewall is enabled).
- Click