1. Product Overview
The XIAOMI MIJIA Graphene Heater Fan is a versatile and efficient heating solution featuring PTC ceramic heating technology, smart control capabilities, a built-in timer, and 70° wide-angle oscillation. Designed for desktop installation, it offers rapid heating and multiple safety features.
Key Features:
- PTC Ceramic Heating Element for efficient warmth.
- Smart Control via Mi Home/Xiaomi Home App.
- Adjustable Thermostat for precise temperature control.
- Overheat Protection for enhanced safety.
- Remote Controlled functionality.
- Tip-Over Protection with automatic shutdown.
- 70° Wide-Angle Oscillation for broad heat distribution.
- Built-in Timer (1, 2, 4, 8 hours).
- Multiple Speed Settings (>Fifth gear).
2. Package Contents
Upon unpacking, please ensure all the following items are present and in good condition:
- MIJIA Smart Graphene Heater × 1
- User Manual × 1
- EU Adapter × 1 (Note: The adapter is sent according to the plug type you selected.)
3. Safety Information
Please read all safety instructions carefully before using the product to prevent injury or damage.
- **Pre-Use Check:** Before first use, verify that the product is intact and the power cord is undamaged.
- **Power Supply:** Use a 220V AC socket with a carrying capacity of not less than 10A. It is recommended to use a dedicated wall socket. Do not share a power strip with other high-power electrical appliances.
- **Placement:** This product is an electrical appliance for close-range use. For direct heating, position it 1 to 2 meters away for optimal effect.
- **Overheating Protection:** The heater is equipped with an overheating protection system that automatically shuts off the device if it gets too hot.
- **Automatic Shutdown:** The device features an automatic shutdown mechanism if it is tilted, enhancing safety.
- **Materials:** Constructed with V-0 rated flame retardant materials.
4. Setup
4.1 Physical Setup
- Place the heater on a stable, level surface.
- Plug the power cord into a suitable 220V AC socket.
- Ensure the power indicator light turns on.
4.2 Connecting with Mi Home/Xiaomi Home App
This product can be controlled via the Mi Home/Xiaomi Home app. Follow these steps to connect your device:
- **Download the App:** Scan the QR code below or search for "Mi Home/Xiaomi Home" in your app store to download and install the app.
- **Open the App:** Launch the Mi Home/Xiaomi Home app.
- **Add Device:** Tap the "+" icon on the upper right corner of the app.
- **Follow Prompts:** Follow the on-screen prompts to add your device. If the QR code scan fails, you can search for the heater's name to add it manually.
Important Note for Chinese Version:
- Because this product is a Chinese version, you must change the country setting in the Mi Home/Xiaomi Home APP to "China" when connecting. The app language can be set according to your local country.
- If the device fails to connect for a certain period, the Wi-Fi of the device needs to be reset.
- Please be aware that the app's full functionality, especially Wi-Fi control, might be restricted to mainland China regions.
5. Operation
5.1 Control Panel Overview
The control panel is located on the top of the heater. Familiarize yourself with the buttons and indicators:
| Component | Function/Indication |
|---|---|
| Power indicator light | Indicates power status. |
| Wi-Fi Indicator | Indicates Wi-Fi connection status. |
| Oscillation Button | Turns the swing mode on/off. |
| Mode Button (M) | Cycles through Natural, Warm, Hot, and Constant Temperature modes. |
| Mode Indicator | Shows current operating mode (Natural Mode, Warm Mode, Hot Mode). |
| On/Standby Button | Powers the unit on or puts it into standby. |
| Temperature Button | Adjusts the target temperature in Constant Temperature mode. |
| Scheduled On/Off Button | Sets the timer for standby (1h, 2h, 4h, 8h, Off). |
| Temperature/Scheduled On/Off Indicator | Displays current temperature setting or remaining timer duration. |
5.2 Basic Operation
- **Power On/Off:** Press the On/Standby Button (power symbol) to turn the heater on or put it into standby.
- **Mode Adjustment:** Short press the Mode Button (M) to cycle through:
- **Natural Wind Mode:** Fan operates without heating.
- **Warm Air Mode:** Provides warm air, approximately 1200W power.
- **Hot Air Mode:** Provides hot air, approximately 2000W power.
- **Constant Temperature Mode:** Maintains a set target temperature.
- **Adjust Target Temperature:** In Constant Temperature Mode, short press the Temperature Button (thermometer symbol) to cycle through target temperatures: 22°C, 24°C, 26°C, 28°C.
Tip: In Constant Temperature Mode, only the corresponding temperature indicator lights up. If the room temperature exceeds the set target, the heater will stop heating.
- **Timed Standby:** Short press the Scheduled On/Off Button (clock symbol) to set a timer for standby: 1 hour, 2 hours, 4 hours, 8 hours, or Off. The indicator light will show the remaining time.
- **Swing Mode:** Short press the Oscillation Button (oscillation symbol) to turn the 70° wide-angle oscillation on or off.
- **Child Lock:** To enable or disable the child lock, press and hold the Scheduled On/Off Button (clock symbol) and the Temperature Button (thermometer symbol) simultaneously for 7 seconds.
Note: After the heater fan has been heating, it will blow for 30 seconds to dissipate residual heat before entering standby. If natural air runs for more than 30 seconds, this cool-down period is not needed.
5.3 Wi-Fi Reset
If you encounter issues connecting to the app or need to reset network settings:
- When the power is on, press and hold the On/Standby Button (power symbol) for 7 seconds to enter network distribution mode and reset the Wi-Fi.
5.4 Factory Reset
To restore the heater to its factory settings:
- When the power is on, press and hold the On/Standby Button (power symbol) and the Mode Button (M) simultaneously for 7 seconds.
6. Care & Maintenance
Proper care and maintenance will ensure the longevity and optimal performance of your heater fan.
- **Before Cleaning:** Always turn off and unplug the heater. Allow it to cool down completely before cleaning.
- **Cleaning the Exterior:** Use a clean, soft, and damp cloth to wipe the exterior of the heater. Do not allow water to drip into the heater.
- **Disassembly:** Do not attempt to disassemble the heater for care or maintenance.
- **Drying:** After cleaning, ensure the heater is completely dry before using or storing it.
- **Protection:** Avoid bumping or scratching the heater to prevent damage to its surface coating and potential rusting.
- **Storage:** If storing the heater for an extended period, place it in its original packaging and store it in a dry place.
7. Troubleshooting
Refer to the table below for common issues and their solutions.
| Issue | Possible Cause | Solution |
|---|---|---|
| The heater is not connecting to power. | The power cord is not plugged in properly. | Check whether the plug and the power cord are plugged in properly. |
| The heater is not turned on. | Press the power button to turn the heater on. | |
| The heater is not placed steadily. | Place the heater steadily on a level surface. | |
| The heater does not work. | The heater is not started. | Press the on/standby button on the control panel to start the heater. |
| The temperature is too high, and the heater automatically turns off to ensure safety. | Keep the air inlet and the air outlet clear and unobstructed, and restart the heater after it cools down. | |
| The child lock function is enabled. | Disable the child lock. | |
| The heater cannot be found in the app. | The network connection fails. | Reset the Wi-Fi (see Section 5.3). |
| The Wi-Fi signal is weak. | Keep the phone and the heater close to the Wi-Fi signal source. | |
| The power cord is not plugged in properly. | Plug the heater in properly and turn it on again. | |
| The heater makes unusual sounds when it is moved or shaken. | The steel ball in the anti-tilt switch rattles. | Place the heater on a level surface steadily and avoid shaking it violently. |
7.1 Wi-Fi Indicator Status Description
| Product Working Status | Wi-Fi Indicator Status |
|---|---|
| Awaiting connection | Blinking slowly (on for 0.2 seconds, then off for 0.8 seconds, repeatedly) |
| Network connected successfully | On |
| Reconnecting automatically after a disconnection | Blinking quickly (on for 0.1 seconds, then off for 0.2 seconds, repeatedly) |
| Updating the firmware | Blinking (on for 0.05 seconds then off for 0.1 seconds, and on for 0.05 seconds then off for 0.8 seconds, repeatedly) |
| Network connection function disabled | Off |
8. Specifications
| Attribute | Value |
|---|---|
| Brand Name | XIAOMI |
| Model Number | LSNFJ04ZM |
| Electric Heater Type | Fan Heater |
| Heating Element | PTC |
| Power Source | AC |
| Voltage | 220 V |
| Power (W) | 1200-2000W |
| Number of Speed Settings | >Fifth gear |
| Application Area | 11 - 20 M² |
| Area Heated | ≥20㎡ |
| Installation | Desktop |
| Function | Adjustable Thermostat, Overheat Protection, Remote Controlled, Tip-Over Protection |
| Certification | RoHs, CE, EMC, RoHS |
| Use | LIVING ROOM |
| Origin | Mainland China |
8.1 Package Dimensions and Weight
- Length: 56 cm
- Width: 24 cm
- Height: 24 cm
- Weight: 3.17 kg
9. User Tips
- **App Control:** The heater is highly praised for its app control capabilities, making it convenient to operate remotely.
- **Compact and Powerful:** Despite its small footprint, users find it surprisingly powerful and effective at heating rooms.
- **Initial Use Smoke:** It is normal to observe some smoke or odor during the very first operation. This typically dissipates after a few minutes of use.
- **App Region Lock:** Be aware that the Mi Home/Xiaomi Home app, being a Chinese version, may require setting your region to "China Mainland" for full functionality. Some users report that app control via Wi-Fi might only work within mainland China.
- **Temperature Setting:** The app might have a minimum temperature setting of 22°C.
- **Noise Level:** While generally efficient, some users have noted a minimal noise level during operation.
10. Frequently Asked Questions (FAQ)
- Q: Does the app work outside of China?
- A: The Mi Home/Xiaomi Home app is a Chinese version. While the app itself can be downloaded globally, full Wi-Fi control functionality, especially for this specific model, may be restricted to mainland China regions. You might need to set your app region to "China" for it to connect.
- Q: Is this product only a heater, or does it also function as a fan?
- A: It functions as both a heater and a fan. It has a "Natural Wind Mode" which operates as a fan without heating, in addition to "Warm Air Mode" and "Hot Air Mode."
- Q: Does this heater have Alexa integration?
- A: There is no information indicating direct Alexa integration for this model. Control is primarily through the Mi Home/Xiaomi Home app.
11. Warranty and Support
For warranty information, technical support, or service inquiries, please refer to the official XIAOMI website or contact your retailer. Keep your purchase receipt as proof of purchase.
A digital version of this user manual is available for download. You can access the PDF version here.