I. Safety Information
Please read this manual carefully before using the device and follow the instructions for proper operation. Damage caused by non-compliance with the instructions will not be covered by warranty.
WARNING
-
Fingerprint Sensor Care:
- Do not scrape the fingerprint sensor with sharp objects to avoid permanent damage.
-
Water Exposure:
- Do not expose the product to environments with water leakage or splashing.
-
Password Security:
- Please modify the default administrator PIN code immediately after installation and configuration. Keep the mechanical key properly.
-
Battery Requirements and Management:
- Use alkaline batteries for the device (batteries not included).
- Do not remove the battery during setup and operation.
-
Low Battery Replacement:
- Replace all batteries immediately if there is a low battery alarm. Ensure correct polarity (+/-) when installing batteries.
II. Package Contents
This packaging list is for reference only. Please refer to the actual packaging contents.
-
User Manual (PDF available at this link)
-
1. Front Panel
-
2. Back Panel
-
3. Mortise Installation kit
-
4. Smart Lock Installation kit (screws and components)
-
5. Mechanical key x2
-
6. Drilling Template
-
7. IC Card x2
III. Product Overview
Diagram
This diagram illustrates the key components of the smart door lock, including the screw holes, battery cover, reset button, indoor handle, indoor deadbolt, password area, IC card area, doorbell, fingerprint area, handle, backup power port, and keyhole.
Parameters
| Feature | Specification |
|---|---|
| Model | H1 |
| Product Material | Aluminum Alloy Body, Tempered Glass Panel |
| Unlock method | Fingerprint/Password/IC card/Mechanical key/APP |
| Recognition Time | ≤0.5s |
| False Acceptance Rate | ≤0.001% |
| Operating Temperature Range | -10°C-65°C |
| Operating Humidity | 45%-90%RH |
| Emergency Power | DC 5V (TYPE-C interface, can be connected to a power bank for power supply) |
| Power Supply | 6V (1.5V 4pcs AA batteries) |
| Current | Quiescent current≤70µA, Dynamic current≤200mA |
| Compatible Door Thickness | 40-60mm wooden door |
| Protection Level | IP66 |
Other Notes
-
User Capacity: 300
- Administrator: Capacity: 9, IDs: 001-009, Access Methods: Password, Fingerprint, IC Card
- Ordinary Users: Capacity: 291, IDs: 010-300, Access Methods: Password, Fingerprint, IC Card
- Remark: Maximum capacity of passwords, fingerprints, and IC cards is 100 for each.
-
Emergency Power Port:
- When the door alarm indicates low battery power, power the lock through the emergency power port.
-
Security Features:
- If any user attempts to open the lock using a password, fingerprint, or card, after 3 consecutive errors, the system will prompt an alarm.
- After 5 consecutive errors, the system will lock for 30 seconds and trigger an alarm. If there is no operation for more than 10 seconds, the system will automatically exit.
-
Password Peeping Prevention Function:
- You can add extraneous codes before and after the password to prevent peeping. For example: XXX password XXX, then press # to confirm. The correct password must be included in the input.
-
Remote Unlock Request:
- Press # directly to trigger the doorbell and request a remote unlock if Wi-Fi is configured.
-
Unlocking Log:
- After configuring Wi-Fi, the unlocking log will be reported to the Tuya App.
-
Combination Unlock Mode:
- Combination unlock must be opened with 2 types of unlock mode, such as password + fingerprint, password + IC card, and fingerprint + IC card.
- Administrator can unlock directly without verifying the second user.
-
Restoring to Factory Mode:
- Remove the battery cover and keep pressing the "Reset" key until you hear "operation successful". The lock will then be restored to factory mode.
IV. Installation
Overall Pre-installation Instructions
- It is recommended that the installation be performed by professionals, and the door thickness requirement is 40mm-60mm.
- Before installing the lock, please attach the mat to the front/back lock.
- Do not squeeze the connecting wires during installation to avoid line failure.
- During the installation and debugging process, please keep the door half-open until the debugging is completed.
- After installation, please test whether functions such as fingerprint, password, IC card, key, and front/rear handle unlocking are working properly.
- If the door lock cannot be used normally, please check whether it is improperly installed or the connecting wire is loose, etc., and reinstall it according to the installation instructions.
This diagram shows the various components and their placement during installation, including the battery cover, fastening screws, terminal wire, installation board, silicone pad, battery spring, square shaft, mortise, handle, connecting screw tube, and front/back panels.
Step 1: Drill Holes On Door And Frame
Use the drilling template to drill the needed holes on the door.
The drilling template indicates positions for the upper through-bolt hole, wire-through hole, mortise mounting groove, handle spindle hole, and bottom through-bolt hole.
Step 2: Installation The Mortise
- Adjust the backset of Mortise (if needed).
- Tighten up the 4 fixed screws when inserting the mortise, and ensure that the lock body and door panel remain level after installation.
To adjust the mortise, push up, rotate the lock tongue 180°, then push the latch to complete the reversal.
If the mortise holes are centered in the door hole, no adjustment is required. If the latch holes are NOT centered, adjust mortise. Note: The square hole must be horizontal. When the latch bolt bevel faces outwards, it is for inward door opening. When the latch bevel faces inwards, it is for outward door opening.
Step 3: Change The Handle Direction (If Needed)
Adjust the handle direction according to the door opening direction:
- Unscrew the cross screw from the reversible hole.
- Rotate the handle 180 degrees.
- Screw the cross screw into the hole corresponding to the door opening direction: When facing the back side of the front lock, screw on the right for left-hand opening, screw on the left for right-hand opening.
- Perform the same operation for the rear panel.
Diagrams show handle orientation for right open and left open doors. Ensure the red triangle symbol on the floating rotor is at the bottom.
Step 4: Installation Front Panel
Note: Before installing the front lock, secure the bolts and screws in place and pass them through the backplate of the front lock to slide and adjust the position.
The studs can slide according to the actual situation. Ensure the arrow icon points down.
Step 5: Connect Wire Connector And Install The Back Panel
- Install the rear locking plate.
- Remove the rear lock battery cover.
- After connecting the front and rear locks, carefully arrange them and insert them into the slot holes. Then, thread the floating rotor hole of the rear lock onto the square shaft, and secure the rear lock with three screws.
Slide the screw to the front lock stud position and tighten it.
Note: The wire connectors can only be connected in one way.
Step 6: Install 4pcs AA Batteries And Battery Cover
After installing the battery, align the battery cover with the rear lock, then slide it downward to secure. To remove the battery cover, slide it upward.
Slide down to close the lid. Slide up to open the lid.
Step 7: Complete Installation
Insert the key and test the door lock.
Push down to unlock. Lift up to lock. Consistent inside and outside. Note: When testing the lock opening and closing operations, if it is not in the unlocked state mentioned above, please check whether the triangular symbol on the floating rotor of the front lock is in the downward position.
V. How to Use
Pre-Setup Instructions
- The default administrator PIN code is [123456#].
- [*] to return to the previous menu, [#] to confirm.
- Please keep your mechanical key stored outside as a backup.
- If the keyboard can't be woken up, press and hold the reset button until you hear "operation successful" to restore factory default.
Language Settings
After turning on the device, if you need to switch the language, please enter the following content in the initialized state:
- 555666880# [English]
- 555666881# [Vietnamese]
- 555666882# [Portuguese]
- 555666883# [Arabic]
- 555666884# [Russian]
- 555666885# [Thai]
- 555666886# [Spanish]
- 555666887# [Indonesia]
- 555666888# [Chinese]
Menu Structure
Wake up the keyboard. Press [* #] followed by [123456] to enter the setting menu.
- [1] Administrator Setting
- [1] Add Administrator
- [2] Delete Administrator
- [3] Network Setting
- [2] User Setting
- [1] Add User
- [2] Delete User
- [3] System Setting
- [1] Voice Setting
- [2] Verification Mode Setting.
- [4] To Restore Factory Default
Operation Manual
1. Administrator Setting:
1.1 Add Administrator
Follow the steps below to add an administrator:
- Touch the keyboard to wake up the system.
- Enter the administrator password (default: 123456).
- Press [1] for administrator setting.
- Press [1] to add an administrator.
- Please add the ID number (001-009) and press [#] to confirm.
- Enter 6 or more digits new password twice and press [#] to confirm.
- Broadcast current operation is successful.
Remark: Fingerprint: Enter 5 times. Password: Enter 6 or more numbers twice. IC Card: Enter once.
1.2 Delete Administrator
Follow the steps below to delete an administrator:
- Touch the keyboard to wake up the system.
- Enter the administrator password.
- Press [1] for administrator setting.
- Press [2] to delete the administrator.
- Please enter ID number (e.g., 002) and press [#] to confirm.
- Operation successful.
Remark: Cannot delete the current administrator ID you are using.
1.3 Network Setting
Follow these steps to pair your device with your application:
- Touch the keyboard to wake up the system.
- Enter the administrator password.
- Press [1] for administrator setting.
- Press [3] for network setting.
- Press [1] for hotspot connection or [2] for intelligent connection.
2. User Setting:
2.1 Add User
Follow the steps below to add a user:
- Touch the keyboard to wake up the system.
- Enter the administrator password.
- Press [2] for user setting.
- Press [1] to add user.
- Please enter ID number (010-300) and press [#] to confirm.
- Enter 6 or more digits new password twice and press [#] to confirm.
- Broadcast current operation is successful.
Remark: Fingerprint: Enter 5 times. Password: Enter 6 or more numbers twice. IC Card: Enter once.
2.2 Delete User
2.2.1 Delete User by ID Number
Follow the steps below to delete a user by ID:
- Touch the keyboard to wake up the system.
- Enter the administrator password.
- Press [2] for user setting.
- Press [2] to delete user.
- Enter the ID number (010-300) and press [#] to confirm.
- Operation successful.
2.2.2 Delete All Users
Follow the steps below to delete all users:
- Touch the keyboard to wake up the system.
- Enter the administrator password.
- Press [2] for user setting.
- Press [2] to delete all.
- Press [#] to confirm.
- Operation successful.
3. System Setting:
3.1 Voice Setting
Follow the steps below to adjust voice settings:
- Touch the keyboard to wake up the system.
- Enter the administrator password.
- Press [3] for system setting.
- Press [1] for voice setting.
- Press [1] for opening volume or [2] for closing volume.
- Operation successful.
3.2 Verification Mode Setting
Follow the steps below to adjust verification mode settings:
- Touch the keyboard to wake up the system.
- Enter the administrator password.
- Press [3] for system setting.
- Press [2] for verification mode setting.
- Press [1] for single unlock mode or [2] for combination unlock mode.
- Enter the number of the unlock mode that you want to use.
- Operation successful.
4. Restore Factory Default:
Follow the steps below to restore the lock to factory defaults:
- Touch the keyboard to wake up the system.
- Enter the administrator password.
- Press [4] to restore factory default.
- Press [4] and then confirm.
- Operation successful.
VI. Software Installation
1. Download App:
Search and download "Smart Life" or "Tuya Smart" in major application markets.
Look for the Smart Life app on Google Play or the App Store.
2. Registration:
If you don't have an App account, you may choose to register or log in by authentication code. If you have an account already, please login.
VII. Add The Smart Lock to The APP
Use Intelligent Setting Connect (Preferred Mode)
Note: This smart lock only supports 2.4G network and won't work with 5G network. Please check if your home network is 2.4G and make sure that your phone has been connected to the 2.4G WiFi router.
- Follow the steps in the "Operation Manual, section 1.3 Network Setting". Press [2] for intelligent connection. The keypad display will be gone, indicating it has entered pairing mode.
- Turn on the Bluetooth on your phone.
- Turn on the Smart Life App, Tap '+' then "Add Device" at the top right corner of the App homepage. The app will automatically discover the device.
- Join your network.
- Device is added successfully when you hear "operation successful".
Use Hotspot Setting to Connect (Alternative)
Note: This smart lock only supports 2.4G network and won't work with 5G network. Please check if your home network is 2.4G and make sure that your phone has been connected to the 2.4G WiFi router.
- Follow the steps in the "Operation Manual, section 1.3 Network Setting". Press [1] for hotspot connection.
- Turn on the Smart Life App, Tap '+' then "Add Device" at the top right corner of the App homepage. Add Manually → Camera/Lock → Smart Lock → Lock (WiFi).
- Join your network.
- Choose AP mode and connect your mobile phone to the device's hotspot.
- Join the network "Smart Life-xxxx" to connect the door lock.
- Device is added successfully when you hear "operation successful".
VIII. Smart Features
1. Remote Unlock
- Touch the keyboard to wake up the system, then press [#]. The app will receive a request to allow or refuse door opening.
2. Online Password
- Click to get a dynamic password for temporary, time-sensitive use, allowing one-time access or access within 1 year.
3. Temporary Password
- Click to set a temporary password for temporary, time-sensitive use, allowing one-time access or access within a limited time frame.
4. Alarm Record Notification
- The system will automatically record the doorbell call history and incorrect unlocking attempts and push notifications to the software.
5. History of Unlocking Operation
- The system will automatically record the lock's operational history, including records of the user's name and user actions.
6. Member Management
- Users can be added or deleted in the app. Click the corresponding user to add fingerprints, passwords, and cards.
IX. User Tips
- Mortise Size Check: Before installation, verify that the included 50x50mm mortise (22x195mm) is compatible with your door's existing latch mechanism to avoid gaps.
- Careful Installation: The assembly instructions can be detailed. Take your time, follow each step precisely, and ensure all wires are connected correctly and not pinched.
- Fingerprint Setup: Setting up fingerprints can be tricky. Ensure you follow the instructions for entering your fingerprint multiple times (5 times for administrators and users) for better accuracy.
- Volume Adjustment: If the lock's voice prompts are too loud, you can adjust the volume through the System Settings menu (Press [* #] + [123456], then [3] for System Setting, [1] for Voice Setting, and choose [1] for opening volume or [2] for closing volume).
- Remote Unlock Functionality: If the unlock button in the Tuya app is not working, ensure your Wi-Fi configuration is correct and the lock is properly connected to the app.
- Mechanical Key Backup: Always keep your mechanical keys in a safe, accessible location outside the property for emergency access.
X. Troubleshooting
- Lock Not Unlocking Normally: Check if the installation was done correctly, especially the handle direction and the position of the triangular symbol on the floating rotor of the front lock (it should be in the downward position when unlocked). Ensure connecting wires are secure.
- Low Battery Warning: If the lock issues a low battery alarm, replace all 4 AA batteries immediately. Ensure correct polarity. You can also use a USB power bank for emergency charging via the Type-C port.
- System Alarm Triggered: If the lock alarms after incorrect attempts, it will lock for 30 seconds after 5 consecutive errors. Wait for the lockout period to end before trying again.
- Fingerprint Reader Inaccuracy: Ensure the fingerprint sensor is clean and free from debris. Re-enroll your fingerprint, making sure to follow the instructions for multiple scans (5 times) to capture a comprehensive print.
- Loud Operation: Adjust the voice prompt volume through the System Settings menu as described in the User Tips section.
- Tuya App Unlock Button Not Responding: Verify the lock's Wi-Fi connection status in the app. Ensure your phone has a stable internet connection. If the issue persists, try re-adding the lock to the app.
- No Amazon Alexa Support: This product is primarily designed for Tuya Smart Life integration. Direct Amazon Alexa support may not be available.
XI. Maintenance
- Battery Replacement: Replace all 4 AA alkaline batteries when a low battery warning is issued. Do not mix old and new batteries.
- Cleaning: Wipe the lock's surface and fingerprint sensor with a soft, dry cloth. Avoid using abrasive cleaners or solvents that could damage the finish or electronic components.
- Environmental Protection: Protect the lock from direct water exposure or splashing. Ensure the operating temperature and humidity are within specified ranges.
- Fingerprint Sensor Care: Avoid scratching the fingerprint sensor with sharp objects.
XII. Warranty and Support
For warranty information and technical support, please refer to the seller's policies or contact Milfra Official Store directly. Keep your purchase records for any warranty claims.
XIII. Disclaimer
1. THE MANUFACTURER assumes no responsibility for any errors and reserves the right to change the information in this document without notice.
2. Failure to comply with the recommendations in this manual may result in accidents or damage. THE MANUFACTURER will not be held responsible for any loss or damage. Please use this product with care and at your own risk.
Made in China