1. Introduction
The IKSLED AC7036T-F100 is a hidden touch sensor switch designed to control lighting or other compatible loads. It features the ability to sense touch through non-metallic materials such as wood or glass, up to a thickness of 5cm, allowing for discreet installation. This switch operates on AC 110V-240V and provides a simple on/off function.
2. Important Safety Warnings
Please read and understand all safety instructions before installation and use.
- The sensor cable carries high voltage. Always ensure the power supply is disconnected before attempting any installation, removal, or maintenance.
- The circuit board inside the sensor also carries high voltage. Do not disassemble the housing or attempt to directly touch the circuit board.
- This product is non-dimmable. Do not connect to dimmable circuits or attempt to use with dimmable loads.
- Do not exceed the maximum power rating of 400 Watts.
3. Package Contents
Please verify that all items are present in your package:
- 1 x IKSLED AC Sensor Control Switch (Model: AC7036T-F100)
- 1 x Touch Sensor Pad with connecting wires
4. Specifications
| Feature | Specification |
|---|---|
| Model Number | AC7036T-F100 |
| Brand Name | IKSLED |
| Switch Type | Touch On/Off Switch |
| Voltage | 100V-240V AC |
| Max Power | 400 Watt |
| Function | Touch to turn on; touch again to turn off. Non-dimmable. |
| Sensor Diameter | 98mm |
| Sensor Thickness | 8mm |
| Penetration Depth | Up to 5cm (through wood/glass) |
| Material | Plastic |
| Is Smart Device | No |
| Origin | Mainland China |
| Certification | RoHS, LVD, EMC, CE, CCC |
| EU LVD Voltage | High voltage: Above 50Vac or 75Vdc |
| High-concerned chemical | None |
| Package Dimensions (L x W x H) | 17cm x 12cm x 2cm |
| Package Weight | 0.079 kg |
5. Setup and Installation
Follow these steps carefully to install your IKSLED Hidden Touch Sensor Switch. Ensure power is disconnected before starting.
5.1 Wiring Diagram
The sensor control switch supports various load types, including LED lights, energy-saving lamps, exhaust fans, water pumps, and high-power lamps, provided the total power does not exceed 400W.
Wiring Instructions:
- Wiring 1 (AC100V-240V Lamp): Connect the Live (L) and Neutral (N) wires from your AC power source to the 'L in' and 'N in' terminals of the control switch. Connect the lamp's Live and Neutral wires to the 'L out' and 'N out' terminals respectively.
- Wiring 2 (12V/24V Lamps with Constant Voltage Adapter): Connect the AC power source to the 'L in' and 'N in' terminals of the control switch. Connect the output of the control switch ('L out' and 'N out') to the input of a constant voltage adapter (DC12V-24V). Then connect the 12V/24V lamps to the output of the adapter.
- Wiring 3 (AC100V-240V Load): Connect the AC power source to the 'L in' and 'N in' terminals of the control switch. Connect the AC100V-240V load directly to the 'L out' and 'N out' terminals.
Always ensure correct polarity and secure connections.
5.2 Sensor Pad Placement
- Peel off the backing from the double-sided tape on the sensor pad.
- Mount the sensor pad on the back side of the panel (e.g., inside a cabinet door, under a wooden surface, or behind glass).
- Ensure the sensor pad is securely fixed in place before powering on for testing. The touch-sensitive area should be aligned with where you intend to touch on the front surface.
6. Operating Instructions
Once installed and powered on, the IKSLED AC7036T-F100 switch operates as follows:
- To Turn On: Lightly touch the designated touch-sensitive area on the surface (wood, glass, etc.) where the sensor pad is mounted. The connected load will turn on.
- To Turn Off: Touch the same designated area again. The connected load will turn off.
This switch provides a simple ON/OFF function and is not designed for dimming. Repeated touches will toggle the power state.
7. Maintenance
- Keep the switch and sensor pad dry. Avoid exposure to moisture or liquids.
- Clean the exterior of the control module and the surface above the sensor pad with a soft, dry cloth. Do not use abrasive cleaners or harsh chemicals.
- Ensure proper ventilation around the control module to prevent overheating.
8. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Light/Load does not turn on/off. | No power supply. Incorrect wiring. Sensor pad not securely fixed. Material too thick or unsuitable. |
Check if the power supply is connected and active. Verify all wiring connections according to the diagram. Ensure the sensor pad is firmly attached to the surface. Confirm the material thickness is within 5cm and is non-metallic. |
| Light/Load flickers or behaves erratically. | Load exceeds maximum power. Loose connection. Interference. |
Ensure the connected load does not exceed 400 Watts. Check all wiring connections for tightness. Relocate the sensor or switch away from potential sources of electromagnetic interference. |
| Sensor is unresponsive. | Sensor pad damaged. Control module malfunction. |
Inspect the sensor pad for visible damage. If damaged, replacement may be necessary. If all other troubleshooting fails, contact customer support. |
9. User Tips
- Ensure the sensor pad is placed on a clean, flat surface for optimal touch response.
- Test the switch thoroughly before final installation to confirm proper functionality through your chosen material.
- For best results, avoid placing the sensor directly over metal objects or within close proximity to strong electrical fields.
10. Warranty and Support
This IKSLED product comes with a 1-year warranty from the date of purchase, covering manufacturing defects. Please retain your proof of purchase for warranty claims.
For technical support, troubleshooting assistance, or any questions regarding your product, please contact us:
- Support Contact: 0086 13421343580
A detailed user manual (PDF) is available for download. Please refer to the seller's product page for the link to the official PDF document.