BAOFENG UV-5R Mini

Contents

Baofeng UV-5R Mini Walkie Talkie User Manual

Comprehensive Guide for Setup, Operation, and Maintenance

1. Getting Started & Safety Warnings

Thank you for purchasing the Baofeng UV-5R Mini. This dual band/dual display/dual watch radio is designed for secure, instant, and reliable communications. Please read this manual carefully to ensure maximum performance and safe operation.

1.1 Important Safety Information

WARNING! European Users:

Operation of this unit in Transmit mode requires a valid Amateur Radio License from your respective Countries Amateur Radio Licensing Authority for the Frequencies and Transmitter Power levels that this Radio transmits on. Failure to comply may be unlawful and liable for prosecution. Refer to the "EU" specification guide 2014/53/EU.

ATTENTION! Programming the Radio:

When programming the radio, start by reading the factory software data, then rewrite this data with your desired frequency, etc., to a new saved code plug. Otherwise, errors may occur. Use the programming cable with a PC to program the authorized frequency, bandwidth, power, etc. Your programming must comply with your FCC (or EU other country) license certification.

ATTENTION! RF Energy Exposure and Product Safety:

Before using this product, read the RF Energy Exposure and Product Safety Guide that ships with the radio, which contains instructions for safe usage and RF energy awareness and control for compliance with applicable standards and regulation.

1.2 FCC Part 15 / IC Compliance

This device complies with Part 15 of the FCC rules and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

  1. This device may not cause harmful interference.
  2. This device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.

1.3 FCC RF Exposure Guidelines

WARNING!

It is up to the user to properly operate this radio transmitter to ensure safe operation. Please adhere to the following:

  • Do not use the radio with a damaged antenna. If a damaged antenna comes into contact with the skin, a minor burn may result.
  • Please contact your local dealer for a replacement antenna.

Hand-Held Operation (Held-to-Face)

This device was evaluated for typical hand-held (held-to-face) operations with a 1-inch spacing from the front of the radio. For hand-held operation, the radio should be held 1 inch from the user's face to comply with FCC RF exposure requirements.

Body-Worn Operation

This device was evaluated for body-worn operations with the supplied belt-clip accessory. All necessary accessories are included in the package; any additional or optional accessories are not required for compliance with the guidelines. Third-party accessories (unless approved by the manufacturer) should be avoided as these might not comply with FCC RF exposure guidelines.

1.4 Precautions for Portable Terminals

Operating Prohibitions

To protect against property loss, bodily injury, or even death, observe the following safety instructions:

  1. Do not operate the product in a location containing fuels, chemicals, explosive atmospheres, or other flammable or explosive materials. In such locations, only an approved Ex-protection model is allowed for use, and any attempt to assemble or disassemble it is strictly prohibited.
  2. Do not operate the product near or in any blasting area.
  3. Do not operate the product near any medical or electronic equipment that is vulnerable to RF signals.
  4. Do not hold the product while driving.
  5. Do not operate the product in any area where use of wireless communication equipment is completely prohibited.

Important Tips

To help you make better use of the product, observe the following instructions:

  1. Do not use any unauthorized or damaged accessory.
  2. Keep the product at least 2.5 centimeters away from your body during transmission.
  3. Do not keep the product receiving at high volume for a long time.
  4. For vehicles with an airbag, do not place the product in the area over the airbag or in the airbag deployment area.
  5. Keep the product and its accessories out of reach of children and pets.
  6. Operate the product within the specified temperature range.
  7. Continuous transmission for a long time may lead to heat accumulation within the product. In this case, keep it at a proper location for cooling.
  8. Handle the product with care.
  9. Do not disassemble, modify, or repair the product and its accessories without authorization.

2. Setup

2.1 Package Contents

The standard package for the Baofeng UV-5R Mini includes the following items:

Standard Package Contents

Image: Standard Package Contents including radio, battery, antenna, Type-C cable, lanyard, belt clip, user manual, and box.

Item Quantity (PCS)
Radio1
Battery1
Antenna1
Lanyard1
Operation Manual1
Belt Clip1
Type-C Cable1
Box1

*Charger and power adapter are subject to the final configuration of the dealer. The charging instructions in this manual may not be appropriate if Type-C charging method is used.

2.2 Attaching the Antenna

Turn the antenna clockwise until it is tight. To remove the antenna, turn it counterclockwise.

CAUTION:

  • Do not hold the radio antenna in your hand, as this will reduce the performance of the radio and the life of the antenna.
  • Do not shake the radio with the top of the antenna in your hand, as this will degrade the performance and life of the radio antenna.

2.3 Battery Installation and Charging

The UV-5R Mini radio uses a Type-C charging port, allowing for convenient charging from various sources.

Type-C Charging Methods

Image: Various Type-C charging methods including USB, car charger, power bank, and computer charging.

When using the terminal for the first time, a low battery warning may occur. It is recommended to turn off the radio during charging. The battery's LEDs provide an indication of the current state of charge:

Indicator Light Charging Status
Red light is always onCharging
Green light is always onCharging complete

2.4 Wireless Programming Software

The UV-5R Mini supports advanced Bluetooth frequency programming. This feature allows you to customize and adjust frequencies easily without cables. Simply pair your device via Bluetooth and program the frequencies to suit your specific needs.

Bluetooth Programming Interface

Image: Smartphone screen showing the Bluetooth programming interface for the 5R Mini.

To program the radio wirelessly, you need to install the dedicated APP program. Download it by scanning the QR codes below:

QR Codes for Programming Software

Image: QR codes for downloading the programming software for iOS and Android devices.

Wireless Programming Steps:

  1. Press [MENU] + [4] to enter Wireless CPS.
  2. Press [MENU] + ▲/▼ to select "On"; the Bluetooth icon will be displayed on the first line of the screen.
  3. After the APP is opened, allow Bluetooth and location functions on your cell phone.
  4. Select the walkie-talkie model (5Rmini Series), connect the radio, and click "Walkie-talkie". A connection success prompt will appear, and you will return to the home page.
  5. Read the radio data: After finishing the frequency reading, click the program to enter the program details. In the program details interface, you can program channel information, frequency mode, and optional functions.
  6. Save Profile: The programmed profile allows you to save the profile as a new profile and name it. If you select Replace Program, click Replace Program and save.
  7. Write data to radio: Click home page, select program, click 'Write' to enter write frequency. The radio will restart automatically when finished writing frequency.

3. Operating Instructions

3.1 Basic Operations

Turning Your Radio On and Off

  • To turn your radio ON, turn the [Volume/Power] rotary knob clockwise.
  • To turn your radio OFF, turn the [Volume/Power] rotary knob counterclockwise.

Setting the Volume

  • Increase volume by turning the [Volume/Power] rotary knob clockwise.
  • To decrease volume, turn the [Volume/Power] rotary knob counterclockwise.
  • Do not hold the radio close to your ear. If the volume is set to an uncomfortable level, it could hurt your ear.

Locking or Unlocking Keypad

To avoid accidentally changing radio settings:

  1. Press and hold the [ * ] key to lock the keypad until the screen displays the "6" icon.
  2. In lock mode, you can turn the intercom on and off, adjust the volume, receive, transmit, send call tones, send emergency alerts, and listen to channels. All other functions remain locked.
  3. In lock mode, press and hold the [ * ] key to unlock the keypad until the "6" icon is no longer displayed.

3.2 Keypad Entry

You can enter radio aliases, channel aliases, numbers, etc., using the radio's numeric keypad.

  1. To switch between input methods, press [#] key.
  2. Press 1 to enter a special character (except in numeric input mode, where the number 1 is entered).
  3. Press 0 to enter a space (except in the numeric input mode, in which special characters are entered).

3.3 Channel Selection and Memory

Select a Channel

The channel is the channel through which the signal is transmitted.

  • Press the [V/M] button to toggle between VFO and channel mode to select channel mode.
  • Press the ▲/▼ buttons or the rotary encoder to select the desired channel.
  • Enter the channel number using the keypad. For example, to switch to channel 64, enter 064 (3 digits).

Channel Memory

In Frequency and Standby mode, you can store frequencies and parameters.

  1. Press [MENU] [3] [MENU] [1] [5], the screen will display "MEMCH".
  2. Press [MENU] to enter the function. Press the ▲/▼ buttons to select the channel, then press [MENU] to store it. A sound tone will confirm that the storing succeeded.
  3. Press [EXIT] to exit to return to standby mode.

NOTE:

  • If you want to set CTCSS tones, DCS codes, or the frequency offset, you must do it before storing the channel.
  • Stored channels are displayed as CH-, other channels have no CH- display.

Delete a Channel (DEL-CH)

In VFO mode and in standby mode:

  1. Press [MENU] [3] [MENU] [1] [6], the screen will display "DELCH".
  2. Press [MENU] to enter the function. Press the ▲/▼ buttons or rotate the encoder to select the channel you want to delete, then press [MENU] to confirm.
  3. To return to standby mode, press [EXIT] key.

NOTE: Channel 1 cannot be deleted.

3.4 Main Band / Sub Band Switch

In standby mode, press the [A/B] key to toggle between the A and B bands to switch between the main/sub bands. The main band is the highlighted band. The darker displayed band is the sub-band.

3.5 VFO / Channel Switch

Press the [V/M] button to switch between VFO and channel display. VFO mode will display the 'VFO' icon. MR mode will display the channel serial number.

3.6 Setting the VFO Frequency

Turn the radio to VFO mode, then press the [A/B] key to switch to the main channel.

  1. Input the VFO frequency directly with the keypad.
  2. Press the ▲/▼ button or rotary encoder to adjust the VFO frequency in the set frequency step.

3.7 Call Service (PTT)

All radios in the group must be set to the same channel and sub-code to communicate.

To ensure optimal reception volume, keep the distance between the microphone and your mouth at 2.5 cm to 5 cm when transmitting.

  • Initiate a call: Select a channel, press and hold the [PTT-A] key. The radio transmits on segment A (upper screen), and the red indicator light is always on. Then speak into the microphone with a normal voice tone. Press and hold the [PTT-B] key. The radio transmits on the B segment (lower screen), and the red indicator light is always on. Then speak into the microphone in a normal voice tone.
  • Receive a call: After releasing the [PTT] key, the radio is in a receivable state. When receiving a call, the green indicator light is always on.
Dual PTT Functionality

Image: Diagram illustrating the Dual PTT functionality with PTT 01 and PTT 02 buttons.

Note: In standby, press and hold the 8 key to toggle the transmission power.

3.8 Emergency Alarm

The emergency alarm allows the terminal to initiate an alarm to seek help from a companion or control center during an emergency.

  • In standby mode, press the preset [SOS] key to enable or disable the emergency alarm function.

3.9 Flashlight

The radio is equipped with a strong flashlight function, useful in dark environments.

Strong Flashlight Feature

Image: The radio with its flashlight function activated, illuminating a dark road.

  • In standby mode, press the preset 5 key to turn the flashlight on or off.

3.10 FM Radio Function

Set the [SK1] key to the radio function via Menu >> Radio Set >> Press SK1.

Turn on the radio and press the SK1 key [FM Radio] to enter radio mode. The screen displays the tuning frequency. The following operations can be performed:

  • Press ▲/▼ key to search for radio channels at the preset step frequency.
  • Press the [#] key to search for radio channels automatically; the screen displays 'SEEK...'.
  • Press [EXIT] key to switch frequency band between 65.0/75.0MHz.
  • Press SK1 key [FM Radio] to exit radio mode.

3.11 Monitor Function

Press and hold the pre-programmed [Monitor] key to enter monitor mode and listen for weak signals on the current channel. You can also listen to the volume level of the radio when you are not receiving. This allows you to adjust the volume, if necessary. Release the [Monitor] key to exit the monitor mode.

3.12 Frequency Search (Wireless Copy Frequency)

The wireless copy frequency feature simplifies the intercom configuration process, improves work efficiency, and ensures consistency and reliability of communication.

Wireless Copy Frequency

Image: Two UV-5R Mini radios demonstrating wireless copy frequency.

Press the pre-programmed [SEARCH] key or press and hold 5 key. The radio enters frequency search state, and the screen displays "SEARCH...".

  • Press [#] key to switch the searching band, such as VHF/UHF, etc.
  • The frequency and CTCSS/DCS code will be displayed after searching is completed.
  • Press [MENU] to save the channel.

3.13 Reverse Frequency Function

Short press the [ * ] key in relay mode to invert the receive and transmit frequencies. The screen shows 'R' icon. This function is often used in repeater channels, and is effective when there is a frequency difference between the receive and transmit frequencies.

3.14 Talk Around Function

In repeater mode, press [ * ] to switch between Talkaround Mode and Repeater Mode. The screen displays between 'T' icon and 'R' icon. In Talkaround mode, the receive frequency is equal to the transmit frequency.

3.15 Repeater Activation Tone

Turn on the radio, press and hold the [PTT] key, then press the [SK1] to transmit 1750Hz audio to activate a repeater in hibernation.

3.16 Voice-Activated Transmit (VOX)

Enable VOX function to transmit automatically through voice without pressing the PTT key. After speech stops, it will stop transmitting and wait for receiving.

To enable VOX:

  1. In Standby status, press [MENU][2][MENU][4] to enter Vox Switch.
  2. Press [MENU][2][MENU][5] to enter Vox Level, press ▲/▼ to select VOX level (level 1-9). The smaller the value, the higher the sensitivity. The 'V' icon is displayed at the top of the screen. (Default is off).
  3. Press [MENU] key to save the setting and return to the upper menu.

To turn off VOX: Repeat the above operation and select OFF. The 'V' icon disappears.

3.17 Dual Watch

When in Dual Watch mode, the radio can receive the frequency set for channel A or B.

To enable Dual Watch:

  1. Press [MENU] [2] to enter Radio Set.
  2. Press [MENU] + ▲/▼ to select "15 Dual Watch".
  3. Press [MENU] key to enter Dual Watch Setting, press ▲/▼ key to select "On".
  4. Press [MENU] key to save and return to the upper menu. The dual watch function will be turned on, and the icon 'D' will be displayed on the first line of the screen.

To disable Dual Watch: Repeat the above operation and select "Off". The Dual Watch function is turned off, and the icon 'D' disappears.

3.18 Stopwatch Function

Press and hold the [MENU] key to enable the stopwatch function.

  • Press the [MENU] key to start the stopwatch.
  • Press the [MENU] key again to stop the stopwatch.
  • Press the [EXIT] key to exit the stopwatch function.

3.19 Weather Radio / Scan Weather Channel

Your radio has a NOAA Weather Radio function to receive weather reports from designated NOAA stations, and a NOAA Weather Scan function to scan all 10 channels.

To turn on NOAA Weather Scan:

  1. Press and hold the [0] key for 3 seconds. The weather icon appears. The radio will go to Weather band mode.
  2. Press and hold the [#] key for 3 seconds to start automatic scanning of all 10 channels and stop on active channels. Pressing and holding the [#] key for 3 seconds during a NOAA weather scan will stop the scan.
  3. After stopping NOAA weather scan, you can manually select the weather channel by pressing the ▲ or ▼ key.
  4. To exit the Weather Radio broadcast mode, press the 5 key or [PTT] key.
Channel Number RX Frequency MHz Channel Number RX Frequency MHz
CH-01162.550CH-06162.500
CH-02162.400CH-07162.525
CH-03162.475CH-08161.650
CH-04162.425CH-09161.775
CH-05162.450CH-10163.275

NOTE: Weather Channels Wx 1 Thru 10 are Receive-only channels for NOAA and Canadian weather broadcasts. You cannot transmit on these channels.

3.20 Using Menu Functions

The radio features a full keyboard and open menu operation. You can navigate menus using arrow keys or numerical shortcuts.

Basic Use with Arrow Keys

  1. Press the [MENU] button to enter the menu.
  2. Use the ▲/▼ buttons or the encoder to navigate between menu items.
  3. Once you find the desired menu item, press [MENU] again to select that menu item.
  4. Use the ▲/▼ buttons or the encoder to select the desired parameter.
  5. To confirm your selection, press [MENU] to save your setting and return to the main menu. To cancel changes, press [EXIT] to reset the item and exit the menu.
  6. To exit the menu at any time, press the [EXIT] button.

Using Menu with Shortcuts

  1. Press the [MENU] button to enter the menu.
  2. Use the numerical keypad to enter the number of the menu item.
  3. To enter the menu item, press the [MENU] button.
  4. For entering the desired parameter, you can use arrow buttons or the numerical keypad for the short-cut code.
  5. Confirm selection with [MENU] or cancel with [EXIT].
  6. To exit the menu at any time, press the [EXIT] button.

4. Maintenance

4.1 General Maintenance

Your Two Way Radio is an electronic product of exact design and should be treated with care. The suggestions below will help you to fulfill any warranty obligations and to enjoy this product for many years.

  • Do not attempt to open the radio for any reason! The radio's precision mechanics and electronics require experience and specialized equipment; for the same reason, the radio should under no circumstances be realigned as it has already been calibrated for maximum performance. Unauthorized opening of the transceiver will void the warranty.
  • Do not store the Radio under direct sunlight or in hot areas.
  • High temperatures can shorten the life of electronic devices and warp or melt certain plastics.
  • Do not store the radio in dusty and dirty areas.
  • Keep the Radio dry. Rainwater or damp will corrode electronic circuits.
  • If the Radio diffuses a peculiar smell or smoke, please shut off its power immediately and take off the charger or battery from the radio.
  • Do not transmit without an antenna.

4.2 Battery Maintenance

Charging Prohibitions

To protect against property loss, bodily injury, or even death, observe the following safety instructions:

  1. Do not charge or replace your battery in a location containing fuels, chemicals, explosive atmospheres, or other flammable or explosive materials.
  2. Do not charge a wet battery. Please dry it with a soft and clean cloth prior to charging.
  3. Do not charge a battery suffering deformation, leakage, or overheat.
  4. Do not charge your battery with an unauthorized charger.
  5. Do not charge your battery in a location where strong radiation is present.
  6. Overcharge is prohibited as it may shorten the life of your battery.

Maintenance Instructions

To help your battery work normally or prolong its life, observe the following instructions:

  1. Accumulated dust on the charging connector may affect normal charging. Please use a clean and dry cloth to wipe it regularly.
  2. It is recommended to charge the battery between 5°C and 40°C. Violation of this limit may cause battery life reduction or even battery leakage.
  3. To charge a battery attached to the product, turn it off to ensure a full charge.
  4. Do not remove the battery or unplug the power cord during charging to ensure a smooth charging process.
  5. Do not dispose of the battery in fire.
  6. Do not expose the battery to direct sunlight for a long time, nor place it close to other heating sources.
  7. Do not squeeze and penetrate the battery, nor remove its housing.

4.3 Transportation Instructions

  1. Damaged batteries must not be transported.
  2. To avoid short circuits, separate the battery from metal parts or from each other if two or more batteries are transported in one packaging.
  3. The radio must be switched off and secured against switch-on if the battery is attached.

The content of the shipment must be declared in the shipping documents and by a Battery Shipping Label on the packaging. Contact your hauler for local regulations and further information.

5. Troubleshooting

This section provides guidance for common issues. If you encounter a problem not listed here, or if the issue persists, please refer to the full PDF manual or contact customer support.

Problem Possible Cause / Solution
Radio does not power onBattery is depleted or not properly installed. Ensure battery is charged and correctly seated.
Cannot transmit or receiveIncorrect frequency/channel selected. Antenna not properly attached. Power output too low. Check settings and antenna connection.
Poor audio quality / StaticWeak signal, interference, or squelch level set too high. Adjust squelch or move to a clearer area.
Keypad is unresponsiveKeypad might be locked. Press and hold the [ * ] key to unlock.
Radio emits peculiar smell or smokeImmediately shut off power and remove the battery. Do not attempt to use the radio further. Contact support.

6. Specifications

The Baofeng UV-5R Mini is a compact and versatile amateur radio. Below are its key technical parameters:

UV-5R Mini Features and Dimensions

Image: Mini Shape Ultra-thin Body with key features and dimensions.

Parameter Value
Brand NameBAOFENG
ModelUV-5R Mini
Tuner TechnologyVHF, UHF
Receiver FrequencyFM 76-108 MHz; AM 108-136 MHz; VHF 136-174 MHz, UHF 400-520 MHz, 350-390 MHz
Transmit FrequencyVHF 144-148 MHz; UHF 420-450 MHz
Output Power (w)5w-10w (Adjustable 5W/2W RF output)
Channel Spacing25.0KHz (Wide) / 12.5KHz (Narrow)
Storage Channel999 Channels
Operation VoltageDC 7.4 V ±10%
Battery Capacity1600 mAh
Dimensions67x182x41mm (Antenna Not Included) / 108x52x37mm (No antenna)
WeightApprox. 200g (Battery pack included)
Transmission Current≤1600mA
Receive Sensitivity0.25µV (12dB SINAD)
Rated Audio Power Output1W @16 ohms
Receive Current≤380mA
Connection for accessories2 pin Kenwood jack
Antenna impedance50 Ohm
WaterproofIP45
Display ScreenYes (1.44" TFT large screen)
CertificationCE, Dot, EAC, EPA, FCC, GMP, RoHS, TGA, UL, KC, pse, weee
FCC ID2AJGM-5RMINI

NOTE: All specifications may be modified without prior notice or liability.

7. Warranty & Support

The accuracy and completeness of the contents are sought in the process of compilation, but we do not bear any responsibility for possible errors or omissions. With the continuous development of technology, we reserve the right to change the design and specification of the product without notice. No copy, modification, translation, and dissemination of this handbook may be made in any form without the prior written authorization of our department.

For detailed information and further assistance, please refer to the comprehensive user manual available in PDF format: Baofeng UV-5R Mini User Manual (PDF).

If you have any questions or require support, please contact the seller or manufacturer directly.

8. User Tips

Based on user feedback and general best practices for walkie-talkies:

  • Portability: The UV-5R Mini is noted for its compact and lightweight design, making it very comfortable and easy to carry for various activities like outdoor rescue, maritime transport, or hotel use.
  • Versatility: Users appreciate its versatile features, including Dual PTT, Type-C charging, Bluetooth programming, and a strong flashlight.
  • Wireless Copy Frequency: Utilize the wireless copy frequency feature to quickly and easily set up communication with other radios without complex manual programming.
  • Battery Life: To maximize battery life, ensure you charge the radio within the recommended temperature range (5°C to 40°C) and avoid overcharging.
  • Programming: Take advantage of the Bluetooth programming via the mobile app for convenient frequency management.
  • Safety First: Always adhere to the safety guidelines, especially regarding antenna handling and operating in hazardous environments.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.