Heltecbms HTNA-310S

Contents

Heltecbms 3-10S Sodium Ion Battery BMS Protection Board User Manual

Model: HTNA-310S Series

Brand: Heltecbms

1. Introduction

This manual provides detailed instructions for the safe and effective use of your Heltecbms 3-10S Sodium Ion Battery BMS (Battery Management System) Protection Board. This board is designed to protect sodium ion battery packs from overcharge, over-discharge, overcurrent, and short circuits, while also providing passive balancing for optimal battery performance and longevity.

Multiple Heltecbms BMS boards for 3-10S sodium ion battery packs, showing 'Max 20A current' and 'Na-ion batteries' labels.

Image: Overview of Heltecbms 3-10S Sodium Ion Battery BMS Protection Boards.

2. Safety Information

Please read and understand all safety precautions before installation and operation. Failure to follow these instructions may result in electric shock, fire, serious injury, or damage to the product and connected devices.

  • Always wear appropriate personal protective equipment (PPE), including safety glasses and insulated gloves, when working with batteries and electrical components.
  • Ensure all power sources are disconnected before performing any wiring or maintenance.
  • Verify all connections and polarity carefully before applying power. Incorrect wiring can cause severe damage to the BMS and battery pack.
  • Do not short-circuit the battery terminals or the BMS output.
  • Keep the BMS away from water, moisture, and flammable materials.
  • Do not attempt to disassemble or modify the BMS. Refer all servicing to qualified personnel.
  • Ensure adequate ventilation around the battery pack and BMS during operation.

3. Product Overview

The Heltecbms HTNA-310S series BMS is a hardware-based protection board designed for nominal 3.0V sodium ion battery cells, supporting configurations from 3S to 10S. It features a common port for both charging and discharging.

Key Features:

  • Protection Functions: Overcharge Protection, Over-Discharge Protection, Overcurrent Protection, Short Circuit Protection.
  • Passive Balancing: Ensures uniform voltage across battery cells for extended battery life.
  • Robust Design: Features a front aluminum heat sink for efficient heat dissipation and an insulated, flame-retardant back for enhanced safety.
Front view of the BMS board with aluminum heat sink.

Image: Front view showing aluminum heat sink for heat dissipation.

Back view of the BMS board, showing insulated and flame-retardant material.

Image: Back view showing insulated and flame-retardant material.

4. Specifications

Feature Specification
Model SeriesHTNA-310S
BrandHeltecbms
TypeSodium Ion Battery BMS
Applicable Battery CellsNominal 3.0V Sodium Ion Battery Cells
Strings Supported3S, 4S, 5S, 6S, 7S, 8S, 9S, 10S
Dimensions (L x W x H)60mm x 40mm x 8.5mm (±1mm error range)
Connection PortCommon Port (Charge and Discharge)
Balance FunctionPassive Balanced BMS
Continuous Charging Current15A
Charging Protection Current Limit20A
Continuous Discharge Current20A
Discharge Protection Current Limit30A
Overcharge Voltage (Single Channel)3.95V ± 0.025V
Overcharge Release Voltage (Single Channel)3.8V ± 0.05V
Overdischarge Voltage (Single Channel)1.5V ± 0.05V
Overdischarge Release Voltage (Single Channel)1.8V ± 0.05V
Balanced Current56mA
Over Temperature ProtectionNone
CertificationCE
OriginMainland China
Usage ScenarioEnergy Storage BMS

Charging Voltage per String Configuration:

String Count Charging Voltage
3S11.85V
4S15.8V
5S19.75V
6S23.7V
7S27.65V
8S31.6V
9S35.55V
10S39.5V

5. Setup and Wiring Instructions

Important: Strictly follow the wiring diagrams provided. When assembling, first check that the voltage of each individual battery cell is within the rated voltage range. If any cell voltage exceeds 3.8V (for sodium ion cells), the protection board may not be able to be awakened. Ensure all battery cells are connected in series before welding the protection board.

General Wiring Steps:

  1. The wiring starts from the B- terminal of the BMS.
  2. Connect the balance wires in sequence: B-, B1, B2, ..., up to B+.
  3. After confirming that all balance wires are correctly connected, measure the voltage between the P+ and P- terminals of the BMS. This voltage should be consistent with the total voltage of the battery pack (B+ to B-).
  4. If the voltages are not consistent, use a suitable charger to power on the battery pack and BMS to awaken the board.

Below are specific connection diagrams for different string counts. The principle remains the same for all configurations.

Wiring diagram for a 3S Sodium Ion Battery BMS.

Image: 3S Connection Diagram. Shows the BMS connected to three battery cells in series, with B- to the negative terminal of the first cell, and balance wires connecting between cells up to B+ of the last cell. Charger and Load connect to P- and Pack+.

Wiring diagram for a 4S Sodium Ion Battery BMS.

Image: 4S Connection Diagram. Illustrates the wiring for four series-connected battery cells to the BMS.

Wiring diagram for a 5S Sodium Ion Battery BMS.

Image: 5S Connection Diagram. Shows the wiring for five series-connected battery cells to the BMS.

Wiring diagram for a 6S Sodium Ion Battery BMS.

Image: 6S Connection Diagram. Details the wiring for six series-connected battery cells to the BMS.

Wiring diagram for a 7S Sodium Ion Battery BMS.

Image: 7S Connection Diagram. Illustrates the wiring for seven series-connected battery cells to the BMS.

Wiring diagram for an 8S Sodium Ion Battery BMS.

Image: 8S Connection Diagram. Shows the wiring for eight series-connected battery cells to the BMS.

Wiring diagram for a 9S Sodium Ion Battery BMS.

Image: 9S Connection Diagram. Details the wiring for nine series-connected battery cells to the BMS.

Wiring diagram for a 10S Sodium Ion Battery BMS.

Image: 10S Connection Diagram. Illustrates the wiring for ten series-connected battery cells to the BMS.

6. Operating Instructions

Once correctly installed and connected to your sodium ion battery pack, the BMS operates automatically to provide protection and balancing. No user intervention is typically required during normal operation.

  • Charging: Connect your charger to the designated charging terminals (P+ and P-). The BMS will manage overcharge protection.
  • Discharging: Connect your load to the designated discharging terminals (P+ and P-). The BMS will manage over-discharge, overcurrent, and short circuit protection.
  • Balancing: The passive balancing function will automatically work to equalize cell voltages when the battery pack is at a higher state of charge, typically during charging or when resting.

7. Maintenance

  • Regularly inspect the BMS and all wiring for any signs of damage, corrosion, or loose connections.
  • Keep the BMS clean and free from dust and debris.
  • Ensure the operating environment is within the recommended temperature range for both the BMS and the battery cells.
  • Periodically check the individual cell voltages of your battery pack to confirm proper balancing.

8. Troubleshooting

Refer to the table below for common fault phenomena, their causes, and recommended solutions.

Troubleshooting table for BMS issues including failure to discharge, failure to charge, wiring errors, and component failures.

Image: Troubleshooting Guide for BMS Protection Board.

Fault Phenomenon Fault Inspection and Cause Treatment Method and Maintenance
Failure to Discharge First, connect a suitable charger to charge and wake up. Then, measure the voltage of each battery separately. If the voltage of any battery is lower than 3.0V, the protection board will activate over-discharge protection. If any battery is lower than 3.0V, charge the battery to about 3.7V and balance them. Do not mix good batteries with substandard ones. (If the problem cannot be solved, please contact after-sales service.)
Failure to Charge Measure the voltage of each battery. If the voltage of any battery is higher than about 4.0V, the protection board will activate over-charge protection. If any battery is higher than 4.0V, charge the battery to about 3.7V and balance them. Do not mix good batteries with substandard ones. (If the problem cannot be solved, please contact after-sales service.)
Charge/Discharge Failure Wrong wiring of B-(0V), B1(3.7V), B2(7.4V), B3(11.1V), ……B+ Re-wire or replace with a new board. (If the problem still cannot be solved, please contact after-sales service.)
Over-charge/Over-discharge Failure Wrong wiring of B-(0V), B1(3.7V), B2(7.4V), B3(11.1V), ……B+ Re-wire or replace with a new board. (If the problem still cannot be solved, please contact after-sales service.)
Discharge Protection Check whether the starting power of the load exceeds the over-current protection current of the protection board. Replace with a protection board with larger current. (If the problem cannot be solved, please contact after-sales service.)
Component Cold Solder Joint No connection between one pin of the component and the PCB pad. Can be soldered by yourself. (If the problem cannot be solved, please contact after-sales service.)
Component Short Circuit Short circuit connection between two or more pins of the component. Remove the component and re-solder. (If the problem cannot be solved, please contact after-sales service.)
Electrostatic Breakdown Measure the G pole, D pole, and S pole of the MOS tube in the non-powered state. The forward resistance and reverse resistance of any two pins are both 0. Can remove and replace the MOS tube by yourself. (If the problem cannot be solved, please contact after-sales service.)

9. User Tips

  • Users have reported high satisfaction and excellent performance when the BMS is correctly installed.
  • Double-check all wiring connections, especially the balance leads, to ensure proper functionality and prevent issues.
  • For optimal performance, ensure your battery cells are healthy and balanced before connecting the BMS.

10. Frequently Asked Questions (FAQ)

Q: What type of batteries is this BMS compatible with?
A: This BMS is specifically designed for nominal 3.0V sodium ion battery cells.
Q: Can I use this BMS for LiFePO4 or Li-ion batteries?
A: No, this BMS is optimized for sodium ion battery characteristics and should not be used with other battery chemistries like LiFePO4 or Li-ion, as voltage parameters differ significantly.
Q: What does 'passive balanced BMS' mean?
A: A passive balanced BMS uses resistors to dissipate excess energy from higher voltage cells, bringing them down to match lower voltage cells. This helps maintain overall pack balance.
Q: What should I do if the BMS is not working after installation?
A: First, re-check all wiring according to the diagrams. Ensure individual cell voltages are within the specified range. If the issue persists, refer to the Troubleshooting section or contact customer support.

11. Warranty and Support

For warranty information, technical support, or any inquiries not covered in this manual, please contact the Heltecbms Official Store directly. Ensure you provide your product model and purchase details for efficient assistance.

This product is CE certified, indicating compliance with relevant European health, safety, and environmental protection standards.

© 2024 Heltecbms. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.