keenkee M00149

Contents

Shelf Support Pin Instruction Manual

Brand: keenkee | Model: M00149

1. Product Overview

The keenkee M00149 Shelf Support Pins are designed to securely hold wooden or glass shelves within furniture cabinets, closets, and other units. These self-tapping metal pins provide robust support, complemented by optional silicone caps for glass shelves or a softer finish.

Two keenkee shelf support pins and one silicone cap

Figure 1: keenkee M00149 Shelf Support Pins and Cap

2. Safety & Warnings

▲ Important Safety Information

Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.

  • Warning: This product includes small components. Please keep it away from children under 3 years old. During installation, please place the accessories out of the reach of children.
  • Improper use may cause injury or damage.
  • Do not use if the product is cracked, broken, or deformed.
  • Do not place near fire or high-temperature sources.
  • Use only under normal household conditions.

3. Setup and Installation

The following steps outline the installation process. For a visual guide, please refer to the product video.

  1. Determine Shelf Position: Mark the desired locations for your shelf support pins on the interior of your cabinet or furniture unit. Ensure marks are level and evenly spaced for stable shelf placement.
  2. Install Support Pins: Using a Phillips head screwdriver, screw the self-tapping metal pins directly into the marked positions until they are firmly seated and flush with the cabinet wall. No pre-drilling is typically required for wood, but for very hard materials, a small pilot hole may be beneficial.
  3. Attach Silicone Caps (Optional): If supporting a glass shelf, or if you prefer a softer contact point for wooden shelves, place the clear silicone caps over the exposed end of the metal pins.
  4. Place Shelf: Carefully rest your shelf onto the installed support pins, ensuring it is stable and level.

Video 1: Product demonstration and installation guide.

Glass shelf supported by a keenkee shelf pin with cap

Figure 2: Example of a glass shelf installed with support pins and caps.

Wooden shelf supported by a keenkee shelf pin without cap

Figure 3: Example of a wooden shelf installed with support pins.

4. Operating Instructions

  • Use the product only as intended for supporting shelves.
  • Do not overload the shelves or apply excessive force to the support pins.
  • Inspect the product before each use to ensure pins are secure and undamaged.

5. Maintenance

  • Keep the shelf support pins clean by wiping them with a dry cloth as needed.
  • Periodically inspect the pins for any signs of looseness, wear, or damage.
  • If a pin becomes loose, re-tighten it with a Phillips head screwdriver.

6. Troubleshooting

  • Shelf is unstable or wobbly:
    • Ensure all support pins are fully screwed in and tight.
    • Verify that the pins are installed at the same height and are evenly spaced.
    • Check that the shelf is not overloaded beyond its capacity.
  • Support pin feels loose:
    • Re-tighten the pin with a Phillips head screwdriver.
    • If the screw hole is stripped, consider moving the pin slightly to a new, secure location or using a wood filler to repair the original hole before re-inserting.

7. Specifications

Model NumberM00149
Brand Namekeenkee
MaterialMetal (Iron)
StructureSingle-side Bracket
DIY SuppliesWoodworking
UseFurniture
ColorSilver
Quantity20 pieces per pack

Dimensions:

Dimensional diagram of shelf pin and cap

Figure 4: Dimensional details of the shelf support pin and cap.

  • Total Pin Length: 1 inch (25.5 mm)
  • Screw Part Length: 0.5 inch (12.5 mm)
  • Support Part Length: 0.5 inch (13 mm)
  • Silicone Cap Height: 0.63 inch (16 mm)
  • Silicone Cap Diameter: 0.35 inch (9 mm)

8. User Tips

  • These metal, self-tapping pins with silicone stoppers are noted for their superior quality and strong hold compared to other support types.
  • They are suitable for both wooden and glass shelves, providing versatile support for various furniture needs.
  • Ensure the pins are fully tightened for maximum stability, especially when supporting heavier items.

9. Warranty & Support

For product support, inquiries, or warranty information, please contact the manufacturer or authorized representative:

Manufacturer:

Company Name: Shenzhen Wenxinmeijia Household Product Co., Ltd
Full Address: B1C031 #5 Plaza, Huanancheng Pinghu, Longgang District Shenzhen City
Email: servicenter@keenkee.online
Telephone: +86-13164762726

EU Authorized Representative:

AR Company Name: GAVIMOSA CONSULTORIA, SOCIEDAD LIMITADA
Full Address: CASTELLANA 9141, 28046 Madrid, Spain
Email: compliance.gavimosa@outlook.com
Telephone: +34-688185858

Compliance:

This product complies with relevant health, safety, and environmental protection standards, indicated by the CE Mark.

For a complete user manual and additional documentation, please refer to the official PDF: keenkee M00149 User Manual (PDF)

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.