1. Introduction
The Radtel RT-950 PRO is a versatile multi-band handheld radio designed for professional and amateur radio enthusiasts. It features a wide frequency range, high output power, and advanced functionalities such as GPS/APRS, Bluetooth programming, real-time spectrum analysis, and cross-band repeater capabilities. This manual provides detailed instructions for the safe and effective use of your device.
Video: Overview of Radtel RT-950 PRO features, including Bluetooth programming, NOAA weather reception, power level switching, spectrum analysis, GPS positioning, APRS transmission, shortwave reception, 27MHz transmission, fast frequency copy, and Type-C charging.
2. Safety Information
This product is intended solely for professional use where RF energy radiation requirements can be met. Users must be fully aware of RF radiation hazards and take appropriate measures to comply with RF radiation limits.
2.1. RF Radiation Basics
RF (Radio Frequency) refers to electromagnetic frequencies that can radiate into space. It is a technology widely used in fields such as communications, medical, and food processing, and it generates a certain amount of RF radiation during use.
2.2. FCC Regulatory Requirements
In accordance with the regulations of the Federal Communications Commission (FCC) of the United States, this product must comply with FCC RF radiation limits to be sold in the U.S. market. Manufacturers are required to inform users of important safety precautions by labeling the product, thus enhancing user awareness of radiation protection.
2.3. RF Radiation Safety
To ensure the health and well-being of users, experts from the fields of science, engineering, medicine, health, and industry, along with relevant organizations, have jointly developed RF radiation standards and guidelines, as follows:
- Title 47, Part 2, Subpart J of the Code of Federal Regulations (CFR) by the Federal Communications Commission (FCC) of the United States.
- ANSI (American National Standards Institute) / IEEE (Institute of Electrical and Electronics Engineers) Standard C95.1-1992.
- IEEE Standard C95.1-1999.
- Standards issued in 1998 by the International Commission on Non-Ionizing Radiation Protection (ICNIRP).
2.4. RF Radiation Control and Operating Instructions
To ensure optimal performance and compliance with the radiation limits for occupational or controlled environments as specified in the standards, the transmission time should not exceed a duty cycle of 50% (i.e., a maximum of 50% transmission time). Adhere to the following instructions:
- RF energy radiation is only generated during transmission (talking), not during receiving (listening) or standby mode.
- Maintain a minimum distance of 2.5 centimeters between the device and the body during transmission.
3. Getting Started: Device Overview
Familiarize yourself with the components and controls of your Radtel RT-950 PRO radio.
Image: Front view of the Radtel RT-950 PRO Walkie Talkie, highlighting its display, keypad, and main controls.
3.1. Structure Introduction
- Channel Knob: Used for channel selection.
- Power Switch/Volume Knob: Turns the device ON/OFF and adjusts volume.
- PPT A/B/C Buttons: Programmable Push-To-Talk buttons.
- Side Key 2: Programmable function key.
- Speaker: Audio output.
- Antenna: For transmitting and receiving signals.
- Indicator Light: Shows device status (e.g., charging, transmitting).
- Display Screen: Shows frequency, channel, menu, and status icons.
- Accessory Interface: For connecting external accessories.
- Interface Cover Screw: Secures the accessory interface cover.
- Function Keypad: For menu navigation and function selection.
- Numeric Keypad: For direct frequency input and channel selection.
3.2. Key Functions
| Button | Function |
|---|---|
| OK | Menu Select / Confirm Key. Long press to enter spectrum mode. |
| A/B/C | Short press to switch between A/B/C segments. Long press to enter remote sub-tone scan mode. |
| < / > | Direction Keys |
| Back/Exit | Short press: Exit / Clear Key. Long press to enter frequency sweep mode. |
| V/M | Short press: Switch between Channel Mode and Frequency Mode. Long press to enter the APRS positioning interface. |
| Numeric keys (0-9, *, #) | In standby state: In Frequency Mode, used to set the working frequency; in Channel Mode, used to switch channel. After quick setup, long pressing keys 0-9 allows fast access to the assigned functions. |
3.3. Icon Description
The display uses various icons to indicate the radio's current status and active features.
| Icon | Description |
|---|---|
| VOX | Indicates that the VOX function is enabled. Transmission starts when the microphone's sound pressure level reaches the set threshold. |
| APRS | Automatic Packet Report System. |
| MO | Indicates that the monitor function is enabled. |
| TW | Tri-Watch Active, Simultaneously monitors 3 channels. |
| Lock | Keypad Lock. Appears when the keypad is locked. Long press the # key to unlock. |
| A/B/C | Frequency band selection, Band A / Band B / Band C. |
| RSSI | Signal Strength, Indicates the strength of the received signal. |
| GPS | Switch & Indicator, Toggles GPS positioning with status icon. |
| Z | Repeater Mode ON. |
| Mute | Repeater Mute Enabled, Speaker muted during repeater operation. |
| Music Note | Side Tone Enabled, Indicates that the side tone function is active, producing a tone sound when transmitting DTMF. |
| Bluetooth | Bluetooth Enabled. |
| Battery | Battery Status, Displays the remaining battery power. When the battery is nearly depleted, the outer frame of this symbol flashes, and transmission is prohibited. |
| Power Save | Power Save Icon, Energy-saving mode active. |
| Speaker | Standby Indicator, Indicates the device is in standby/monitoring mode (continuously listening for signals). |
| CT | Analog Sub-audio Tone Indicator. This symbol indicates that the current sub-audio tone is an analog tone. When this symbol appears during transmission, it signifies that an analog sub-audio signal is being transmitted. |
| DCS | Digital Sub-audio Tone Indicator. This symbol indicates that the current sub-audio tone is a digital tone. When this symbol appears during transmission, it signifies that a digital sub-audio signal is being transmitted. |
| H | High Power Indicator. This symbol indicates that the current transmission power is set to high. |
| M | Medium Power Indicator. This symbol indicates that the current transmission power is set to medium. |
| L | Low Power Indicator. This symbol indicates that the current transmission power is set to low. |
| N | Narrowband Mode Indicator. This symbol appears when the channel is operating in narrowband mode. |
| W | Wideband Mode Indicator. This symbol appears when the channel is operating in wideband mode. |
| + | Frequency Mode (+ Frequency Offset) This symbol appears in frequency mode, indicating that the transmission frequency is the reception frequency plus a frequency offset. |
| - | Frequency Mode (- Frequency Offset) This symbol appears in frequency mode, indicating that the transmission frequency is the reception frequency minus a frequency offset. |
| R | Frequency Invert, Inverts RX/TX frequencies in Frequency Mode / Channel Mode. |
| T | Configures transceiver to operate on identical transmit/receive frequencies (simplex communication). |
| Lock | Encryption On, Indicates encryption function is activated. |
| AM | AM Modulation, This icon indicates the current frequency is operating in AM (Amplitude Modulation) demodulation mode. |
| SCR | Scrambler Function: Activates voice encryption to prevent unauthorized monitoring of communications. |
4. Basic Operations
4.1. Power On/Off and Volume
- Power On: Rotate the Power Switch/Volume Knob clockwise until a "click" is heard.
- Power Off: Rotate the Power Switch/Volume Knob counterclockwise until a "click" is heard.
- Volume Adjustment: Rotate clockwise to increase volume, counterclockwise to decrease volume.
4.2. Menu Navigation
- From the home screen, briefly press the 【OK】 key to enter the menu.
- Use the arrow Direction keys (< / >) to navigate.
- Press 【OK】 again to confirm selections.
- Press the Back/Exit key to exit the menu.
4.3. Primary/Secondary Frequency Toggle
On the standby screen, briefly press the A/B/C key to select the primary frequency highlighted in blue background. Non-highlighted frequencies are secondary.
4.4. Channel Mode / Frequency Mode Toggle
On the standby screen, briefly press the V/M key to switch between frequency mode and channel mode. Note: If no valid channels are stored, switching to Channel Mode is disabled.
4.5. Side Key Configuration
Side keys can be configured via programming software. Supported functions include RADIO/MONI/SCAN/SEARCH/SOS/SPECTRUM/Beacon TX.
4.6. Voice-Activated Transmission (VOX) Function
- Operation: Menu → VOX.
- When enabled, the radio automatically enters transmit mode if the microphone detects sufficient sound input.
- Adjustable VOX sensitivity level via menu settings.
- VOX delay time must be configured to maintain transmission continuity.
4.7. Sweep Function
- Assign a side key function as "Sweep" or long-press the Back/Exit key to quickly enter sweep mode.
- It detects the transmitter's carrier frequency and CTCSS/DCS (sub-tone) information, displaying them on the screen.
- Once the carrier frequency is detected, press the 【OK】 key to save the scanned frequency to a specified channel list.
- Supported Ranges: VHF: 136-174 MHz, UHF: 400-520 MHz.
4.8. Repeater Setup
The RT-950 PRO supports cross-band repeater functionality.
Image: Diagram illustrating the Cross-Band Repeater functionality, allowing interoperability between UHF and VHF bands.
- Activating Repeater Mode: Menu → Radio → AB RPT-Mode → ON. The standby screen will display the repeater icon (Z).
- Repeater Requirements: Devices enabling the relay function must operate on different frequency bands.
- Repeater Direction Logic:
- Default Standby State: Both primary and secondary frequencies act as receivers.
- If the primary frequency first receives a valid carrier signal, the secondary frequency automatically becomes the cross-band transmitter.
- If the secondary frequency first receives a valid carrier signal, the primary frequency automatically becomes the cross-band transmitter.
- Speaker Audio Control: Configurable option to enable/disable local speaker audio during repeater operation.
4.9. Emergency SOS Function
- Assign a side key as the [Emergency Alarm] button.
- Operation: Menu → Radio → SOS Mode.
- Local Alarm: The device sounds an alarm tone locally without transmitting any signal.
- Transmit Alarm Tone: Broadcasts the alarm tone via signal transmission.
- Transmit Alarm Code: Sends the alarm code through signal transmission.
4.10. CTCSS/DCS Settings
- Operation: Menu → CTCSS/DCS. Select desired DCS code or CTCSS frequency.
- Function: Enables selective call reception by filtering out unwanted noise signals.
4.11. Scan Function
- Side Key Shortcut: Assign a side key as the Scan Key.
- Configure via: Menu → Radio → Scan Mode.
- Channel Mode: Scans the channels listed in the channel memory (requires power-on scan to add).
- Frequency Mode: Scans frequencies based on the selected step setting.
- Scan Modes:
- Time Mode: Resumes scanning if no operation is performed within 5 seconds after detecting a carrier signal.
- Carrier Mode: Stops scanning upon detecting a carrier signal and resumes scanning 5 seconds after the carrier disappears.
- Search Mode: Stops scanning immediately upon detecting a carrier signal.
4.12. PTT-ID Function
DTMF transmit identity S-CODE or PTT-ID.
- Call Codes (15 preset groups): Menu → Signaling → S-CODE. Assign unique call codes to each segment (A/B/C) or signal type.
- ID Code Setup: Menu → Signaling → PTT-ID.
- Transmission Modes:
- Send on Press: After pressing the PTT, the call code/identity code is sent first, followed by the voice signal.
- Send on Release: After releasing the PTT, the call code/identity code is sent, then the transmission ends.
- Send Both: The call code/identity code is sent both when the PTT is pressed and released.
- Note: Since the identity code operation is independent of the call code, if there is a conflict between the identity code and the call code settings, the identity code will be sent.
4.13. FM Radio Function
Customize a side key as a radio shortcut or long-press a number key to enter radio mode.
- Short press the OK button to access the radio menu and select modulation mode. Set the radio frequency directly using the numeric keys.
- In radio mode, press V/M to toggle between Frequency Mode (VFO) and Channel Mode (MR).
- In Frequency Mode, short press the # key to activate auto-scan for stations.
5. Advanced Features
5.1. GPS/APRS Functionality
The RT-950 PRO supports real-time GPS tracking and APRS (Automatic Packet Reporting System) for location sharing and transmission.
Image: Display showing real-time GPS coordinates and APRS position transmission data.
- One-click GPS Positioning: Quickly obtain your current GPS coordinates.
- APRS Position Transmission: Transmit your location data to other APRS-enabled devices.
5.2. Bluetooth Programming
Program your radio's settings and frequencies conveniently via Bluetooth using a compatible smartphone application.
5.3. Real-time Spectrum Analysis
Visualize radio signals in real-time with the built-in spectrum analyzer, helping you identify active frequencies and signal strength.
Image: Radio display showing real-time spectrum analysis, visualizing signal activity across frequencies.
5.4. Wireless Frequency Copy
Quickly copy frequencies and CTCSS/DCS tones from another radio instantly, simplifying setup for new channels.
Image: Illustration of the Quick Copy Frequency feature, demonstrating how to clone settings from one radio to another.
5.5. NOAA Weather Forecast Reception
Receive NOAA (National Oceanic and Atmospheric Administration) weather forecasts to stay informed about local weather conditions.
5.6. Shortwave (SW), Medium Wave (MW), Long Wave (LW) Reception
The RT-950 PRO supports reception across a broad range of frequencies, including Shortwave (SW), Medium Wave (MW), and Long Wave (LW) bands, with various modulation types (LSB/USB/CW/AM/FM).
5.7. 27MHz TX/RX
The radio is capable of 27MHz transmission and reception, specifically in FM modulation only.
5.8. High Power Output
With 10W high power output, the RT-950 PRO can reach farther and penetrate obstacles more effectively, offering a communication range of 5-15KM.
Image: Illustration demonstrating the extended communication range (5-15KM) achieved with 10W high power output.
6. Maintenance
To ensure optimal performance and extend the lifespan of this product, please follow the guidelines below for daily maintenance and cleaning.
6.1. Daily Maintenance
- Do not pierce or scratch the product with hard objects.
- Do not store the product in environments containing chemical corrosive substances.
- Do not carry or use the product by pulling the earphone cable.
- When not using the earphone jack, cover the interface with the protective cap.
6.2. Cleaning Procedure
Before cleaning, please power off the device and remove the battery:
- Regularly use a dry, clean, lint-free cloth or a soft brush to remove dust from the product surface and charging terminals.
- If the buttons or casing become dirty, use a neutral detergent and a non-woven cloth for cleaning. Do not use detergents, alcohol, sprays, or petroleum-based chemicals as they may damage the surface casing.
- After cleaning, ensure the product is completely dry before use.
7. Troubleshooting
This section addresses common issues you might encounter with your Radtel RT-950 PRO.
- Poor or no reception on MW/LW bands: Some users have reported limited reception on Medium Wave (MW) and Long Wave (LW) bands. Ensure you are using an appropriate antenna for these frequencies and are in an area with good signal strength. If issues persist, this may be a known characteristic of the device.
- Squelch too tight, even on low settings: If the squelch is too aggressive, preventing weaker signals from being heard, try adjusting the squelch level in the menu. If the lowest setting is still too tight, this might be a characteristic of the radio's squelch circuit.
- Radio not turning on: Ensure the battery is fully charged and properly inserted. Check the power switch for proper operation.
- No audio: Check the volume level. Ensure no headphones are connected if you expect sound from the speaker. Verify the squelch setting is not too high.
- Unable to transmit: Check if the keypad is locked. Ensure you are on a valid transmit frequency and have sufficient power.
8. Specifications
| Attribute | Value |
|---|---|
| Radtel Model | RT-950PRO |
| Output Power(w) | 5w-10w (Max 10W) |
| Battery Capacity(mAh) | 2600mAh |
| Waterproof / Water-Resistant | No |
| Battery Included | Yes |
| Storage Channel | 64*15 ZONE |
| Frequency Range | 108-136MHz (RX), 2.3-30MHz (RX), 27MHz (TX/RX), 400-520MHz (TX/RX), 136-174 MHz (TX/RX), 520-1710KHz (RX), 153-279KHz (RX) |
| Dimensions | 130*57*36mm |
| Walkie Talkie Type | Portable |
| Is_Display | Yes |
| Maximum Range | 5km-10km |
| Brand Name | radtel |
| Origin | Mainland China |
| Certification | CE, FCC |
| Air Band | Yes, 108-136Mhz RX |
| Bluetooth Programming | Yes |
| Shortwave RX | LSB/USB/CW/AM/FM |
| Modulation | AM/FM/SSB |
| GPS/APRS | YES |
| SPECTRUM | YES |
| Wireless Frequency Copy | YES |
| NOAA Weather | YES |
| Cross-Band Repeater | YES |
| 27mhz TX/RX | Yes, In FM modulation ONLY |
| Package Length | 28 cm |
| Package Width | 23 cm |
| Package Height | 8 cm |
| Package Weight | 0.699 kg |
9. Warranty and Support
9.1. Warranty Terms
The warranty period for this product starts from the date of sale (based on the date on the sales invoice). The main unit is covered for 12 months, and the battery and charging accessories are covered for 6 months. The following cases will require paid repair services during the warranty period:
- Failure to present this warranty card and the purchase invoice.
- This card shows signs of alteration or does not match the product.
- Defects and damages caused by using this product under non-standard conditions.
- Defects and damages caused by misuse, accidents, water ingress, or negligence.
- Defects and damages resulting from improper testing, operation, repair, installation, modification, or adjustment.
- Defects and damages caused by unauthorized repairs or disassembly.
- Defects and damages caused by force majeure.
- Normal wear and tear from regular use.
9.2. Additional Resources
A detailed user manual in PDF format is available for download. You can access it here: Radtel RT-950 PRO User Manual (PDF).
10. User Tips
- Antenna for HF: For optimal performance on HF bands (e.g., 2.3-30MHz), consider using a suitable external antenna, as the stock antenna may be optimized for VHF/UHF.
- Squelch Adjustment: If you find the squelch too sensitive or too tight, experiment with different squelch levels in the menu to find a balance that allows you to hear weaker signals without excessive noise.
- Bluetooth Programming: Utilize the Bluetooth programming feature with a compatible smartphone app for easier and more flexible radio configuration.
- Explore Features: The RT-950 PRO is feature-rich. Take time to explore functions like Spectrum Analysis, GPS/APRS, and Cross-Band Repeater to maximize your radio experience.
11. Frequently Asked Questions (FAQ)
- Q: What is included in the package?
- A: The standard package typically includes the Radtel RT-950 PRO radio unit, antenna, charging dock, USB charging cable, power adapter, belt clip, and a user manual.
- Q: Is this the new batch with known issues resolved?
- A: While manufacturers continuously improve products, some users have reported that reception on Medium Wave (MW) and Long Wave (LW) bands might still be limited. For specific hardware versions (V1 or V2) and their associated fixes, please refer to the official Radtel support channels or the detailed PDF manual.
- Q: How do I program the radio?
- A: The radio can be programmed manually via the keypad and menu, or more conveniently via Bluetooth using a dedicated smartphone application. Refer to section 5.2 for more details on Bluetooth programming.