1. Introduction
The BRS-TS20 Reactor Head is a high-efficiency, windproof outdoor stove designed for camping, hiking, and other outdoor activities. It functions as both a heat collection pot for boiling water and a versatile heating tool. Its integrated reactor design ensures infrared combustion, high thermal efficiency, and reliable performance even at high altitudes.

Figure 1: BRS-TS20 Reactor Head (Gas tank not included)
2. Safety Warnings
Please read and understand all safety warnings before operating this product.
- This product is for outdoor or well-ventilated environments only. Do not use in tents, cars, rooms, or any other enclosed spaces.
- Avoid direct sunlight or other high-temperature environments.
- Stop use immediately if any gas leakage is detected.
- The structure is precise; do not attempt to modify the product to avoid hazards.
- Do not disassemble or install the gas tank while the stove is lit, or near open flames.
- Keep away from flammable and explosive materials.
- When lighting, do not place your head or hands directly above the stove to prevent burns.
- The metal part of the furnace head becomes extremely hot during use and for up to 5 minutes after use. Do not touch it.
- Never refill used gas tanks; this can lead to serious accidents.
- Children under 12 years of age should not use this product unsupervised.
3. Setup
3.1. Product Components
The BRS-TS20 Reactor Head consists of the following main parts:
- Metal Net: Top protective mesh.
- Metal Wool: Special heating element for infrared combustion.
- Valve Switch: Controls gas flow.
- Valve Body: Connects to the gas tank and houses the valve switch.

Figure 2: Optional Furnace Head Bracket (may be sold separately)
3.2. Gas Tank Installation
- Ensure the valve switch is fully closed by turning it clockwise.
- Connect the valve body to the gas tank and tighten it securely.
- Before ignition: Check for gas leakage. If you detect any odor (e.g., onion-like smell), immediately stop and do not ignite.

Figure 3: Reactor Head with optional bracket installed on a gas tank
4. Operating Instructions
4.1. Igniting the Stove
- Slowly turn the valve switch counter-clockwise to open the gas flow (do not open too wide initially).
- Immediately use an external fire source (e.g., lighter, match) to ignite the furnace head.
Important:
- Do not place your head or any other body part directly above the stove during ignition.
- When using a new gas tank or in high-temperature environments, the gas pressure might be too high, causing flames to float above the metal net, and the metal wool may not glow red.
Solution for floating flames:
- Reduce the gas flow by turning the valve slightly clockwise and wait 1-3 minutes for the flame to settle into the net.
- Then, adjust the gas flow to achieve optimal combustion.

Figure 4: Integrated Reactor with infrared combustion
4.2. Performance
- Thermal Efficiency: Up to 70%.
- Gas Consumption: Approximately 79g/h.
- Boiling Time: Can boil 1 liter of water in about 3 minutes under optimal conditions.
- Heating Element Temperature: Special heating metal wool can reach 800°C.

Figure 5: High thermal efficiency and heating element temperature
4.3. Using as a Heater
The BRS-TS20 Reactor Head can also be used as a flameless heater. It converts gas energy completely into infrared radiant heat, providing effective warmth in outdoor settings.

Figure 6: Using the Reactor Head as an infrared heater
4.4. Closing the Stove
- Turn the valve switch clockwise until it is fully closed and the flame extinguishes.
- Allow the stove to cool completely for at least 5 minutes before handling.
- Once cool, unscrew the stove head from the gas tank.
5. Maintenance
- Keep the stove dry and clean to prevent corrosion.
- Discoloration of the furnace surface during use is normal and does not affect performance.
- Before each use, inspect the O-ring seal at the connection between the valve body and the gas tank to ensure it is present and intact.
- Keep the connection point between the valve body and the gas tank clean to prevent airway blockages.
- For storage, always separate the stove from the gas tank.
- A small amount of gas may leak during installation or disassembly. Perform these actions in well-ventilated areas, away from open flames.
6. Troubleshooting
6.1. Gas Leakage
If you detect any gas odor (e.g., onion-like smell) during installation or before ignition, immediately stop use, ensure the area is well-ventilated, and check all connections for tightness. Do not ignite if a leak is suspected.
6.2. Flame Floating / Metal Wool Not Glowing Red
This can occur with new gas tanks or in high-temperature environments due to excessive gas pressure.
Solution:
- Slightly reduce the gas flow by turning the valve clockwise.
- Wait 1-3 minutes for the flame to settle into the metal net and for the metal wool to begin glowing red.
- Adjust the gas flow as needed for optimal performance.
7. Specifications
| Feature | Specification |
|---|---|
| Ignition Mode | External ignition source (not included) |
| Fuel Type | Butane gas, Propane gas |
| Combustion Power | 1.1 kW |
| Gas Consumption | Approx. 79 g/h |
| Material | Stainless steel, Aluminum alloy, Copper |
| Heat Efficiency | Up to 70% (CE standard not less than 50%) |
| Weight | 0.214 kg |
| Storage Size | Φ105 x H75 mm |
8. User Tips
- This reactor head is designed to fit perfectly with BRS reactor stoves and compatible heat collection pots.
- Users have found this product to offer excellent value for its price and performance.
- Consider purchasing a compatible furnace head bracket for added stability with various cookware.
9. Warranty & Support
For warranty information, please refer to the product packaging or contact your retailer. Keep your proof of purchase for any warranty claims.
A detailed user manual in PDF format is available for download: BRS-TS20 User Manual (PDF).