GGBEE IOS Android

Contents

GGBEE Smart Tag Bluetooth Tracker User Manual

Model: IOS Android

Introduction

The GGBEE Smart Tag Bluetooth Tracker is a versatile item locator designed to help you keep track of your valuables. It supports both iOS Find My / Siri and Android Find Hub, offering a dual-system solution for global tracking. This manual provides detailed instructions for setup, operation, and maintenance to ensure optimal use of your device.

GGBEE Smart Tag Bluetooth Tracker, showing compatibility with iOS Find My and Android Find Hub

Figure 1: GGBEE Smart Tag Bluetooth Tracker with dual system compatibility.

Safety Information

WARNING: Battery Safety

  • Remove and immediately recycle or dispose of used batteries according to local regulations and keep away from children. Do NOT dispose of batteries in household trash or incinerate.
  • Even used batteries may cause severe injury or death.
  • Call a local poison control center for treatment information if ingestion is suspected.
  • Non-rechargeable batteries are not to be recharged.
  • Do not force discharge, recharge, disassemble, heat above 50°C/122°F, or incinerate. Doing so may result in injury due to venting, leakage, or explosion resulting in chemical burns.
  • The compatible battery type is CR2032.
  • The nominal battery voltage: DC 3V.
  • Ensure the batteries are installed correctly according to polarity (+ and -).
  • Do not mix old and new batteries, different brands, or types of batteries, such as alkaline, carbon-zinc, or rechargeable batteries.
  • Remove and immediately recycle or dispose of batteries from equipment not used for an extended period of time according to local regulations.
  • Always completely secure the battery compartment. If the battery compartment does not close securely, stop using the product, remove the batteries, and keep them away from children.

WARNING: Ingestion Hazard

  • This product contains a button cell or coin battery. DEATH or serious injury can occur if ingested.
  • A swallowed button cell or coin battery can cause internal chemical burns in as little as 2 hours.
  • KEEP new and used batteries OUT OF REACH of CHILDREN. Seek immediate medical attention if a battery is suspected to be swallowed or inserted inside any port of the body.

Package Contents

Upon unpacking your GGBEE Smart Tag Bluetooth Tracker, you should find the following items:

  • GGBEE Smart Tag Bluetooth Tracker (with pre-installed CR2032 battery)
  • User Manual (this document)
  • Keychain attachment
Package contents showing the Wireless Tag Dual device and a manual.

Figure 2: Typical package contents.

Specifications

Feature Specification
Brand Name GGBEE
Model Number IOS Android
Operating Language English
Waterproof No
Range 500m
Certification CE
Smart Home Platform Other (iOS Find My, Android Find Hub)
Battery Type CR2032 (3V)
Dimensions (L x W x H) 19cm x 11cm x 3cm (packaging)
Weight 0.024 kg (packaging)

Setup

1. Power On

Press the function button on your Item Locator once. It should emit a single beep, indicating it is powered on.

If the product is not paired within 10 minutes, it will automatically power off. You will need to press the function button again to re-enter pairing mode.

2. Pairing with Android (Google Find Hub)

  1. Download the Google Find Hub app from your device's app store.
  2. Open the Google Find Hub app.
  3. Press the power button on the Smart Tag.
  4. The app should detect "Sualio Tag Dual". Tap "Connect".
  5. Review and agree to the terms of use.
  6. Once connected, you can view the tag's location on the map.

Video 1: Demonstrates the setup process for both Android and iOS devices.

3. Pairing with iOS (Apple Find My)

To use the Apple Find My app, ensure your iOS device is running the latest version of iOS, iPadOS, or macOS.

  1. Open the Find My app on your iPhone or iPad.
  2. Navigate to the "Items" tab and tap the "Add Item" (+) symbol.
  3. Select "Other Supported Items".
  4. Ensure your Item Locator is close to your phone. Wait until you see "S Tag", then tap "Connect".
  5. Follow the on-screen prompts to name your item and select an emoji, then tap "Continue".
  6. Link the item to your Apple ID by tapping "Continue" on the pop-up.
  7. Tap "Finish" to complete the setup. Your Item Locator is now connected.
Step-by-step guide for installing the Smart Tag with iOS Find My app.

Figure 3: Visual guide for iOS Find My app setup.

Operating Instructions

1. Locate Your Item (Nearby)

If your item is nearby, you can make the Smart Tag beep to help you find it:

  • In the Find My (iOS) or Find Hub (Android) app, select your Smart Tag.
  • Tap "Play Sound" to make your Item Locator beep.
Screenshot of a phone showing 'Play Sound' mode with a Smart Tag beeping.

Figure 4: Using the 'Play Sound' feature to locate a nearby item.

2. Locate Your Item (Long Distance)

When your item is out of Bluetooth range, you can use the map feature:

  • Open the Find My (iOS) or Find Hub (Android) app and select your Smart Tag.
  • The app will display the Item Locator's last known location on the map.
  • Tap "Directions" to navigate to the last known location using your device's map application.
Screenshot of a phone showing map directions to a lost item attached to luggage.

Figure 5: Navigating to a lost item's last known location.

3. Left Behind Reminder

Enable the "Notify When Left Behind" toggle in the app. You will receive a notification when you leave your Item Locator behind and it is no longer in range of your device.

A person receiving a 'keys left behind' notification on their phone.

Figure 6: Example of a 'Left Behind' notification.

4. Lost Mode

If you lose your item, you can enable "Lost Mode" to help others find it and contact you:

  1. In the app, under "Lost Mode", tap the "Enable" tab.
  2. A screen detailing Lost Mode will pop up; tap "Continue".
  3. You can enter your phone number or email address and tap "Next".
  4. You may also enter a message that will be shared with the person who finds your item.
  5. Tap "Activate" to enable "Lost Mode".

Note: When "Lost Mode" is enabled, "Notification When Found" is automatically enabled. When "Lost Mode" is enabled, your Item Locator is locked and cannot be paired to a new device.

5. Button Functions

  • Power On (Find My function is on): Press the function button once. It will emit a ringing chime. If not paired, it will close within 10 minutes.
  • Power Off (Find My function is off): Hold the function button for three seconds, then release it. You will hear two beeps.
  • Enable Learn More Information Query: Press the function button two times rapidly. You will hear a confirmation sound. This allows others who find the device to obtain information like the owner's contact (if in Lost Mode) and the device's serial number via the Find My app.
  • Restore Factory Settings (Reset): Press the function button four times rapidly and then hold it a fifth time until you hear a ringing chime. A reset is required to re-enter pairing state and rebind to a new Apple ID account (synchronization of Find My also requires simultaneous unbinding).

Maintenance

1. Battery Replacement

The GGBEE Smart Tag uses a CR2032 3V battery. To replace it:

  1. Use your fingernails at the small gap on the side of your Item Locator to carefully open the case.
  2. Replace the battery with a new CR2032 battery (positive pole upward).
  3. Carefully close the Item Locator, ensuring the compartment is securely fastened.
Smart Tag with keychain, showing its compact design.

Figure 7: The Smart Tag is designed for easy battery access.

Troubleshooting

1. Pairing Issues

If you experience difficulty pairing your device:

  • Network Problems: Pairing may fail due to network issues. Try changing your phone's network (e.g., switch between Wi-Fi and mobile data).
  • First-time Pairing: The first pairing may take a longer time; please wait patiently.
  • Reset Device: If issues persist, reset your item to factory settings (refer to "Button Functions" section) and attempt to pair again.

2. Unwanted Tracking Detection

If your iPhone detects an unknown Item Locator traveling with you, it will send a notification. A sound will start playing from the unknown device to help you find it. These alerts are only activated when an Item Locator is not connected to its owner's phone. Therefore, a friend's Item Locator will not trigger a sound if they are with you.

User Tips

  • Easy Installation: Users report the device is easy to install and pairs quickly.
  • Frequent Updates: The tracker updates frequently, providing accurate location information.
  • Dual System Integration: The device integrates seamlessly with both Apple Find My and Android Find Hub, offering correct positions on both platforms.
  • Versatile Use: Attach it to keys, wallets, backpacks, or even pets for peace of mind.
Examples of the Smart Tag being used on a dog, car keys, a wallet, and a backpack.

Figure 8: The Smart Tag is wearable and suitable for various items.

Regulatory Information

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

FC CE UK CA

Made in China

Warranty and Support

For warranty information and technical support, please refer to the seller's policies or contact their customer service directly. Keep your proof of purchase for any warranty claims.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.