1. Introduction
This manual provides essential information for the safe and efficient operation of your Hikvision DS-KV8113-WME1(C) Video Intercom Villa Door Station. Please read this manual thoroughly before installation and use, and retain it for future reference.
Key Features:
- 2 MP camera with IR supplement for clear night vision.
- One nametag button calling design for straightforward visitor interaction.
- Built-in card reader module for convenient access control.
- Standard Power over Ethernet (PoE) for simplified installation.
- IK08 and IP65 protection levels, ensuring durability against vandalism and weather.
- Convenient mobile control via the Hik-Connect APP.
2. Setup and Installation
2.1 Package Contents
Please check the package for the following items:
- DS-KV8113-WME1(C) Video Intercom Villa Door Station
- Mounting accessories (screws, anchors)
- Quick Start Guide (refer to the PDF for full details)
2.2 Physical Installation
The door station is designed for surface mounting. Ensure the mounting surface is flat and secure.
- Choose a suitable location near your entrance, ensuring clear visibility for the camera and accessibility for visitors.
- Use the provided mounting template (if available in the full manual) to mark drilling points.
- Drill holes and insert wall anchors if necessary.
- Secure the mounting bracket (if separate) to the wall.
- Connect all necessary cables before attaching the device to the bracket.
- Mount the door station onto the bracket and secure it with the provided screws.
Dimensions:
The device dimensions are 174 mm x 91 mm x 29 mm (6.9" x 3.6" x 1.1"). Ensure adequate space for installation.
2.3 Wiring Connections
Refer to Figure 3 for the terminal layout on the back of the device. Make connections as follows:
- LAN: Connect an Ethernet cable for network connectivity and Power over Ethernet (PoE).
- LOCK: Connect to your electronic door lock system.
- ALARM IN: Connect external alarm sensors (e.g., door contact, PIR sensor).
- VIDEO: (If applicable for external video input/output, refer to full manual for specifics).
2.4 Power Supply
The DS-KV8113-WME1(C) supports standard Power over Ethernet (PoE). Connect the device to a PoE-enabled switch or PoE injector using an Ethernet cable. No separate power adapter is required, simplifying wiring.
2.5 Initial Configuration
After physical installation and power-up, use the Hik-Connect mobile application or Hikvision client software (e.g., iVMS-4200) to activate and configure the device. Follow the on-screen instructions within the application for network settings, user management, and linking to indoor stations.
3. Operating Instructions
3.1 Making a Call
Visitors can press the nametag button on the door station to initiate a call to the linked indoor station or the Hik-Connect mobile app.
3.2 Two-Way Audio Communication
Once a call is established, you can engage in real-time two-way audio communication with the visitor through the indoor station or your mobile device.
3.3 Access Control with Card Reader
Present a pre-registered access card to the built-in card reader area on the door station to unlock the connected door. Ensure your cards are properly enrolled in the system during configuration.
3.4 Mobile Control (Hik-Connect APP)
The Hik-Connect app allows you to:
- Receive calls from the door station anywhere.
- View live video feed from the camera.
- Communicate with visitors.
- Remotely unlock the door.
- Manage device settings and users.
3.5 Camera Features
The door station features a 2 Megapixel wide-angle lens with IR supplement for high-quality images, even in low-light conditions.
4. Maintenance
4.1 Cleaning
- Regularly clean the camera lens and the front panel with a soft, damp cloth.
- Do not use harsh chemicals, abrasive cleaners, or solvents, as these can damage the surface.
- Ensure the device is powered off before cleaning if possible, or exercise caution around electrical connections.
4.2 Firmware Updates
Periodically check the Hikvision official website or the Hik-Connect app for available firmware updates. Keeping your device's firmware up-to-date ensures optimal performance, security, and access to new features.
5. Troubleshooting
5.1 Device Not Powering On
- Ensure the Ethernet cable is securely connected.
- Verify that the PoE switch or injector is functioning correctly and providing power.
- Check the network cable for any damage.
5.2 No Video/Audio During Call
- Check network connectivity for both the door station and the indoor monitor/mobile device.
- Ensure the door station is properly configured and linked to the indoor monitor/app.
- Verify microphone and speaker settings in the device configuration.
5.3 Admin Password Prompted on Connection
If the device prompts for an admin password upon initial connection or setup, and you do not know it:
- Default Password: Hikvision devices typically require activation with a new password during initial setup. There is no universal default password once activated.
- Seller-Set Password: If the device was pre-configured by the seller, you must contact the seller directly to obtain the password.
- Password Reset: For security reasons, password reset procedures usually involve physical access to the device or specific software tools. Refer to the official Hikvision support documentation or contact Hikvision technical support for assistance with password recovery.
5.4 Door Not Unlocking
- Check the wiring between the door station's LOCK terminals and the electronic lock.
- Verify the lock type and settings in the device configuration.
- Ensure the access card is correctly registered and authorized.
6. Specifications
| Category | Parameter | Value |
|---|---|---|
| System | Operation System | Linux |
| ROM | 32 MB | |
| RAM | 256 MB | |
| Video | Lens | 1 |
| Resolution | Main stream: 1920 x 1080p; Sub stream: 640 x 480p | |
| FOV | Horizontal: 124°, Vertical: 75° | |
| Supplement Light | IR light, up to 3 m | |
| Audio | Audio Input | 1 built-in omnidirectional microphone |
| Audio Output | 1 built-in loudspeaker | |
| Audio Quality | Noise suppression and echo cancellation | |
| Capacity | User Capacity | 2000 |
| Card Capacity | 10000 | |
| Network | Network Protocol | TCP/IP, RTSP, IPv6, ONVIF |
| Wi-Fi | IEEE802.11b/g/n (2.4G) | |
| Card Reading Freq. | 13.56 MHz | |
| Interfaces | Alarm Input | 4 |
| Network Interface | 1 RJ-45, 10/100 Mbps self-adaptive | |
| Lock Control | 2 relays, Max. 30 VDC 2 A | |
| Door Contact Input | 2 | |
| General | Protective Level | IP65, IK08 |
| Working Temperature | -40 °C to 53 °C (-40 °F to 127.4 °F) | |
| Dimensions (W x H x D) | 174 mm x 91 mm x 29 mm (6.9" x 3.6" x 1.1") | |
| Weight | Net: 0.370 kg; Gross: 0.637 kg | |
| Power Consumption | < 10 W |
7. User Tips
- Admin Password: Always ensure you record the admin password set during the initial activation. If the device was pre-activated, request the password from your seller immediately upon receipt to avoid setup delays.
- Network Stability: For optimal performance, especially for video and audio quality, ensure a stable and strong Wi-Fi or wired Ethernet connection.
- Hik-Connect App: Utilize the Hik-Connect app for remote access and control. It significantly enhances the convenience and functionality of your intercom system.
8. Warranty and Support
For warranty information, technical support, or service inquiries, please contact your original point of purchase or visit the official Hikvision website for regional support contacts.
Please have your product model number (DS-KV8113-WME1(C)) and serial number ready when contacting support.