1. Introduction
This manual provides essential information for the safe and efficient use of your BRS-TS20 Reactor Head Outdoor Heat Collection Pot. Please read all instructions carefully before use and retain this manual for future reference.
The BRS-TS20 is designed for outdoor use, offering high thermal efficiency for heating and boiling water, and can also function as a heater. It is compatible with various heat collection pots.
For a detailed user manual in PDF format, please refer to the official document: User manual (PDF).
2. Safety Warnings
General Safety Precautions:
- This product is intended for outdoor use or in a well-ventilated environment only. It is strictly prohibited to use in tents, cars, rooms, or any other closed environments.
- Avoid use in direct sunlight or other high-temperature environments.
- Stop using immediately if any gas leakage is detected.
- The structure of this product is precise; do not attempt to modify it yourself to avoid danger.
- It is strictly prohibited to disassemble and install the gas tank while the fire is not extinguished, and it is strictly prohibited to do so near an open flame.
- Keep away from flammable and explosive materials during use.
- Do not place your head or hands directly above the stove when lighting to avoid burns.
- The metal part of the furnace head, during use or within 5 minutes after completion, will be very hot. Do not touch it.
- Pay special attention: gas tanks should not be refilled, as this may lead to accidents!
- Children under 12 years of age should not use this product unsupervised.
Important Announcements:
- Keep the stove dry, clean, and free from corrosion.
- Discoloration of the furnace surface during use is a normal phenomenon.
- Before use, check whether the O-seal rubber ring in the connection between the valve body and the gas tank is present and intact.
- Keep the connection between the valve body and the tank clean to avoid blocking the airway.
- When storing, always separate the stove from the gas tank.
- A small amount of gas leakage may occur during the installation and disassembly of stoves and gas tanks. Do not install and disassemble in places with open flames or no air circulation.
3. Product Overview and Components
The BRS-TS20 Reactor Head is designed for versatility and high performance in outdoor conditions.
Figure 3.1: BRS-TS20 Reactor Head (gas tank not included)
The product consists of the following main components:
- Metal Net: Top protective mesh.
- Metal Wool: Special heating element for high thermal efficiency.
- Valve Switch: Controls gas flow.
- Valve Body: Connects to the gas tank and houses the valve switch.
Figure 3.2: Product Diagram showing components and gas tank connection.
The furnace head bracket is a separate component that can be used with the reactor head.
Figure 3.3: Furnace head bracket.
4. Specifications
| Feature | Specification |
|---|---|
| Ignition Mode | External ignition source (Not Included) |
| Fuel Type | Butane gas, propane gas |
| Combustion Power | 1.1 kW |
| Gas Consumption | Approx. 79 g/h |
| Material | Stainless steel, Aluminum alloy, Copper |
| Heat Efficiency | Up to 70% (CE standard not less than 50%) |
| Weight | 0.214 kg |
| Storage Size | Φ105 x H75 mm |
| Type | Other Stove |
| Disposable | No |
| Origin | Mainland China |
Package Dimensions:
- Length: 32 cm
- Width: 23 cm
- Height: 16 cm
- Weight: 0.566 kg
5. Setup
Gas Tank Installation:
- Ensure the valve is closed by turning it clockwise (refer to Figure 3.2, step 2.1).
- Connect and tighten the valve body to the gas tank (refer to Figure 3.2, step 2.2).
NOTICE:
Before ignition, always check for gas leakage. If you detect any odor (e.g., onion-like smell), stop immediately and do not attempt to ignite.
6. Operation
Igniting the Stove:
- Turn the valve switch counter-clockwise. Do not open it too wide initially.
- Use an external fire source (e.g., lighter) to ignite the furnace head.
NOTICE:
- Do not place your head or any other body parts directly above the stove during ignition.
- When using a new gas tank or in high-temperature environments, the gas pressure might be too high, causing flames to float above the metal net, and the metal sponge body may not glow red.
Using as a Heater:
The reactor head can be used as a flameless infrared radiant heater, providing good heating effect.
Figure 6.1: The BRS-TS20 functioning as a heater, emitting infrared radiant heat.
Figure 6.2: Close-up of the integrated reactor, highlighting infrared combustion and high thermal efficiency.
The special heating metal wool can reach temperatures up to 800°C, contributing to its high thermal efficiency.
Figure 6.3: Thermal efficiency up to 70%, with gas consumption around 79g/h. Can boil 1L of water in approximately 3 minutes.
Using with Heat Collection Pots:
The BRS-TS20 is compatible with various sizes of heat collection pots, suitable for different group sizes.
Figure 6.4: Compatible heat collection pots: 1L (1-2 people), 1.7L (2-3 people), 2.5L (4-5 people).
Closing the Stove:
- Turn the valve clockwise to extinguish the flame.
- Allow the stove to cool completely for at least 5 minutes.
- Unscrew the stove head from the gas tank.
7. Maintenance
- Keep the stove dry and clean to prevent corrosion.
- Regularly inspect the O-seal rubber ring in the connection between the valve body and the gas tank for presence and integrity.
- Ensure the connection area between the valve body and the gas tank is clean to avoid blocking the gas flow.
- For storage, always detach the stove from the gas tank.
8. Troubleshooting
Problem: Flames floating above the metal net or metal sponge not glowing red (when using new gas tank or in high-temperature environment).
Solution:
- Turn down the valve and wait 1-3 minutes for the flame to burn into the net.
- Reduce the amount of gas and attempt ignition within the network.
Problem: Gas leakage detected (odor).
Solution:
- Immediately stop using the product.
- Check all connections for tightness.
- Ensure the O-seal rubber ring is correctly seated and undamaged.
- Move to a well-ventilated area and do not attempt to ignite until the leak is resolved.
9. User Tips
No specific user tips were available from reviews or Q&A for this product at this time. Always follow the safety guidelines and operating instructions provided in this manual for the best experience.
10. Warranty and Support
For any product inquiries, technical support, or warranty claims, please contact the seller or manufacturer directly. Keep your purchase receipt as proof of purchase.
Ensure you register your product if a registration process is available to receive updates and support.