ETAxopowo SLC1.5-C

Contents

User Manual: 1.5 inch Transparent OLED Display

Model: SLC1.5-C | Brand: ETAxopowo

1. Introduction

This manual provides detailed instructions for the setup, operation, and maintenance of your ETAxopowo 1.5 inch Transparent OLED Display, model SLC1.5-C. This display features a 128x64 dot matrix, 65K (5:6:5) color depth, and utilizes SPI communication with an LD7138 control chip. It is designed for integration into various electronic projects and equipment, including professional audio, stage, recording, and general display applications.

2. Safety Information

  • Handle the display with care to avoid physical damage, especially to the transparent screen and flexible flat cable (FFC).
  • Ensure proper electrostatic discharge (ESD) precautions are taken when handling the module to prevent damage to sensitive electronic components.
  • Do not expose the display to extreme temperatures, humidity, or direct sunlight for prolonged periods.
  • Verify power supply voltage and polarity before connecting to prevent irreversible damage.
  • Keep out of reach of children.

3. Package Contents

Your package should contain the following item:

  • 1 x ETAxopowo 1.5 inch Transparent OLED Display (SLC1.5-C)

Note: Additional components such as connecting cables, development boards, or power supplies are not included unless specified by your vendor.

4. Setup and Connection

4.1 Physical Dimensions

The display module has the following approximate dimensions:

  • Overall Size: 29.0mm (W) x 48.5mm (H) x 1.01mm (D)
  • Active Area: 24.73mm (W) x 30mm (H)
Diagram showing the physical dimensions of the 1.5 inch OLED transparent screen: 29.0mm width and 36.0mm height.
Figure 1: Display Dimensions (29.0mm x 36.0mm outline)
Detailed engineering diagram showing the front and rear views of the OLED display, including panel outline, transparent area, active area, and protection film details.
Figure 2: Display Front and Rear Diagram with detailed measurements

4.2 Pinout and Connections

The display uses a 15-pin flexible flat cable (FFC) for connection. Refer to the pinout table below for detailed descriptions:

Table detailing the 15-pin interface of the OLED display, including pin numbers, names, descriptions, and types.
Figure 3: 15-Pin Interface Pinout
Pin No. Pin Name Descriptions Type
1VSSAnalog ground.P
2VDDLInternal Logic Power. Capacitor is connected between VDDL and Ground.P
3VDDInterface Power & Analog PowerP
4PSELThis pin enable/disable internal logic power regulator. When this pin is tied with VDD pin, it is the internal logic power regulator enabled.I
5VSSDLogic GNDP
6RSTBReset (Active Low)I
7CSBChip Select (Active Low)I
8A0Address (L: Command, H: Parameter)I
9SCLKSerial clock inputI
10SDINSerial data inputI
11FSYNCFrame Signal & Oscillator Clock output, Kept NCO
12PREColumn Driver Pre-Charge Power for RGB.P
13VCC_CColumn Driver PowerP
14VCC_RThis pin is the power output pin of internal row power regulator. A 4.7uF capacitor is recommended to connect between VCC_R and GND. If Internal row power regulator is disabled, It must be connected to the external high voltage source.P
15VSSAnalog ground.P

General Connection Guidelines:

  1. Connect the VDD (Pin 3) and VDDL (Pin 2) to the appropriate power supply (e.g., 2.8V for VDD, and internal logic power for VDDL, typically connected to VDD if internal regulator is enabled via PSEL).
  2. Connect VSS (Pin 1, 15) and VSSD (Pin 5) to ground.
  3. Connect SCLK (Pin 9), SDIN (Pin 10), CSB (Pin 7), RSTB (Pin 6), and A0 (Pin 8) to your microcontroller's SPI interface and GPIO pins.
  4. Ensure a 4.7uF capacitor is connected between VCC_R (Pin 14) and GND. If the internal row power regulator is disabled, VCC_R must be connected to an external high voltage source.
  5. PSEL (Pin 4) controls the internal logic power regulator. Tie it to VDD to enable the internal regulator.

5. Operating Instructions

The SLC1.5-C OLED display is controlled via a Serial Peripheral Interface (SPI) using the LD7138 control chip. To operate the display, you will need to send commands and data via the SPI bus from a microcontroller or other compatible device.

5.1 Initializing the Display

Before sending display data, the LD7138 controller needs to be initialized. This typically involves:

  1. Powering up the display (VDD, VDDL, VCC_C, VCC_R).
  2. Asserting the RSTB (Reset) pin (active low) to reset the controller, then de-asserting it.
  3. Sending a sequence of configuration commands via SPI to set up parameters like display mode, contrast, segment re-map, and common scan direction. Refer to the LD7138 datasheet for specific command sequences.

5.2 Displaying Graphics and Text

Once initialized, you can send pixel data to the display's internal Graphics Display Data RAM (GDDRAM). The display supports 65K colors (5:6:5 RGB format). Data is typically sent in pages or columns, depending on the chosen addressing mode.

  • SPI Communication: Use the SCLK (Serial Clock) and SDIN (Serial Data Input) pins. The CSB (Chip Select) pin should be asserted (low) during communication.
  • Command/Data Selection: The A0 pin determines whether the data being sent is a command (A0 low) or display data (A0 high).
  • Color Format: Ensure your image data is converted to the 5:6:5 RGB format (5 bits for Red, 6 bits for Green, 5 bits for Blue) before sending it to the display.
1.5 inch OLED transparent screen held in hand, showing a phone number display.
Figure 4: Example of display in operation

6. Maintenance

  • Cleaning: Gently wipe the transparent screen with a soft, lint-free cloth. For stubborn smudges, use a small amount of isopropyl alcohol on the cloth. Avoid abrasive cleaners or excessive pressure.
  • Storage: Store the display in a cool, dry place, away from direct sunlight and extreme temperatures. Keep it in its original anti-static packaging if possible.
  • Handling: Always handle the FFC connector and the display edges carefully. Avoid bending or creasing the FFC.

7. Troubleshooting

Display is blank or shows garbled characters:
  • Check all power connections (VDD, VDDL, VCC_C, VCC_R, VSS, VSSD) for correct voltage and polarity.
  • Verify that the SPI communication lines (SCLK, SDIN, CSB, A0) are correctly wired and that your microcontroller's code is sending the correct initialization sequence.
  • Ensure the RSTB pin is properly toggled during initialization.
  • Confirm that the PSEL pin is tied to VDD if you intend to use the internal logic power regulator.
  • Check the 4.7uF capacitor on VCC_R.
Display shows incorrect colors:
  • Verify that your image data is correctly converted to the 5:6:5 RGB color format before being sent to the display.
  • Check the display's initialization commands for any color-related settings.
Display is dim or uneven:
  • Adjust the contrast setting in your initialization code.
  • Ensure the power supply is stable and providing sufficient current.

8. Specifications

Feature Detail
Product ModelSLC1.5-C
Display TypeTransparent PMOLED
Display Size1.5 inch (Diagonal)
Resolution128 x 64 dots
Display Color65K Colors (5:6:5 RGB)
Control ChipLD7138
Communication MethodSPI (Serial Peripheral Interface)
Power Supply (VCC/VDD)16V (VCC) / 2.8V (VDD)
Voltage Range (Input)USB (5-20V DC)
Physical Dimensions29.0mm x 48.5mm x 1.01mm
Battery IncludedNo
High-concerned chemicalNone
Compatible Equipment StyleProfessional Audio Equipment, Stage Equipment, Recording Equipment, Display Equipment

9. User Tips

  • When prototyping, use a breadboard-friendly FFC connector breakout board to simplify connections.
  • Always double-check your wiring before applying power to avoid damaging the display or your development board.
  • Consider using existing open-source libraries for OLED displays with the LD7138 controller as a starting point for your software development.
  • For optimal transparency, ensure the area behind the display is clear and well-lit.

10. Warranty and Support

For detailed warranty information and technical support, please refer to the official product documentation or contact your point of purchase. A comprehensive user manual in PDF format is available for download, which may contain additional technical details and programming examples.

You can find the official user manual (PDF) at: View User Manual (PDF)

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.