FGHGF B29C-DC7-24V TYPE-C AIR780E-4G

Contents

User Manual: B29C-DC7-24V TYPE-C AIR780E-4G 4-Channel Relay Module

Bluetooth WiFi Development Board with Case

1. Introduction

This manual provides detailed instructions for the B29C-DC7-24V TYPE-C AIR780E-4G 4-Channel Relay Module. This development board integrates Bluetooth and WiFi capabilities with an AIR780E-4G module, designed for users to develop applications using AT commands or directly on the AIR780E.

Key Features:

  • Development based on AT commands or directly on the AIR780E.
  • Onboard AIR780E module with low power consumption, down to 600uA in sleep mode.
  • Flip-top nano SIM card holder for easy installation and removal.
  • Onboard blue AIR780E network status indicator (GPIO27).
  • Supports USB-C power supply and 2.54mm pin header for 5V power.
Top-down view of the AIR780E 4-Channel Relay Module without its case, highlighting the 4G network and four 5V relays.
Figure 1: Top view of the AIR780E 4-Channel Relay Module (without case)
Detailed view of the 4G network 4-channel relay module, emphasizing the four 5V relays.
Figure 2: Detailed view of the 4G Network 4-Channel Relay Module

2. Safety & Warnings

Warning!

  • This product is only for adult use.
  • Please keep out of reach of children and pets to avoid accidental injury or ingestion.
  • Check if the installation is correct before use.
  • If there is abnormal noise or equipment error after installation, please stop the device immediately.
  • Follow all instructions for proper use; misuse may cause harm.
  • Please store in a dry and shady place, away from high temperatures, humidity, and direct sunlight.

3. Package Contents

The package includes the following items:

  • 1 * Relay Module with Case

Note: Only the above package content is included. Other products shown in images are for illustration purposes only and are not included.

Top view of the relay module with its protective case.
Figure 3: Relay Module with Case

4. Specifications

Attribute Value
Product Name AIR780E 4-Channel Relay Module Bluetooth WiFi Development Board with Case DC7-24V TYPE-C AIR780E-4G Module
Brand Name FGHGF
Type ESP Series
Origin Mainland China
High-concerned chemical None
Specification 1 Relay Module
Specification 2 4CH Relay Module
Specification 3 AIR780E Relay Module
Specification 4 AIR780E4G Relay Module
Specification 5 4G Relay Module
Color As Shown
Material Plastic
Dimensions (L x W x H) 15 cm x 15 cm x 2 cm
Weight 0.153 kg

5. Setup Instructions

5.1. Preparations

Before you begin, ensure you have the following:

  • TYPE-C cable (with data function)
  • Windows system computer (Windows 10 or above recommended)
  • Nano SIM card
  • 4G antenna
  • Jumper cap

Connect the SIM card and 4G antenna into the board. Plug in a jumper cap.

5.2. LuaTools Installation

  1. Download the latest version of LuaTools. After decompression, locate the executable file named Luatools_v3.exe.
  2. Create a new folder named "LuaTools" and copy or move Luatools_v3.exe into this folder.
  3. Double-click Luatools_v3.exe to start the installation. If a security warning appears, click "More Information" and then select "Still Want to Run" to complete the installation.
  4. After running LuaTools, a prompt may appear to start an upgrade. Click "Start" to proceed with the upgrade. Once the upgrade is complete, the tool can be used normally.
Screenshot showing detailed LuaTools installation instructions.
Figure 4: LuaTools Installation Steps

5.3. Burning Test Firmware

To burn the test firmware:

  1. Click the "Project Management" Test button in LuaTools.
  2. Click "Create Project" at the lower left corner to create a new item.
  3. Select the firmware for the chip and the script. For demo scripts, refer to the official LuaOS repository and find them in the demo folder.
  4. If the current firmware version of the chip has been burned and is the same as the firmware selected, it is acceptable.
  5. Click "Download Script" to download only the script. For a full refresh, it is recommended to click to download the underlying layer and script.
  6. Only by holding down the BOOT key and powering on can the download be done automatically.
  7. After the download is complete, power on again and the program will run automatically.
Screenshots showing firmware burning and AT firmware flashing procedures in LuaTools.
Figure 5: Firmware Burning and AT Firmware Flashing Procedures

5.4. Flashing AT Firmware to Test Network Status

To flash the AT firmware:

  1. In LuaTools, navigate to the AT firmware flashing section.
  2. Click to download the AT firmware.
  3. Hold down the BOOT key to power on the module. The serial port will be automatically recognized and downloaded.

6. Operating Instructions

6.1. Development with AT Commands

The module supports development using standard AT commands. Connect the module to your computer via the TYPE-C port and use a serial terminal program to send AT commands for controlling the module's functions, including network communication, relay control, and other features of the AIR780E-4G module.

6.2. Direct Development on AIR780E

For advanced users, direct development on the AIR780E module is possible. This allows for more customized and complex applications by programming the module directly.

6.3. Network Status Indicator (GPIO27)

The onboard blue LED connected to GPIO27 indicates the network status of the AIR780E module. Observe this indicator to monitor connectivity and operational status.

7. Maintenance

  • Store the product in a dry and shady place.
  • Avoid exposure to high temperatures, humidity, and direct sunlight.
  • Keep the module clean and free from dust and debris.

8. Troubleshooting

  • Abnormal Noise or Equipment Error: If you encounter any abnormal noise or equipment errors after installation or during operation, immediately stop using the device and disconnect power. Review your connections and software configuration.
  • Installation Issues: Double-check all connections, especially the SIM card, 4G antenna, and jumper cap, to ensure they are correctly installed.
  • Software/Firmware Issues: Ensure LuaTools is correctly installed and updated. Verify that the correct firmware and scripts are being used for your application. Refer to the LuaOS repository for up-to-date resources.

9. User Tips

No specific user tips were available from reviews or Q&A at this time. Always refer to the latest documentation and community forums for advanced usage and best practices.

10. Manufacturer & EU Representative Information

Manufacturer:

Taiyuan aopusite electronic commerce co., ltd
Room 1302, 13th floor, Unit 3, Building 6, Hengda Yayuan Community,
Wanbailin District, Taiyuan City, Shanxi Province Code: 030000
Email: yishun225@outlook.com
Phone: +86 15360170591

EU Authorized Representative:

Outong GmbH
Brehmstr, 56, 40239 Duesseldorf
Email: info@outong.de
Phone: +49 21131054698

11. Compliance

CE Mark

This product bears the CE mark, indicating compliance with relevant European health, safety, and environmental protection legislation.

CE

12. Additional Resources

A comprehensive user manual in PDF format is available for download. This document may contain further details and advanced topics not covered in this summary.

You can view the official PDF user manual here.

© 2024 FGHGF. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.