Jonsbo M201/M202

Contents

JONSBO M201/M202 M.2 SSD Heatsink User Manual

Model: M201 / M202

1. Introduction

Thank you for choosing the JONSBO M201/M202 M.2 SSD Heatsink. This manual provides essential information for the proper installation, operation, and maintenance of your heatsink to ensure optimal performance and longevity of your M.2 Solid State Drive.

Safety Warnings & Precautions

  • Do not use this product in humid environments.
  • Do not disassemble internal components without authorization.
  • Ensure adequate ventilation around your system to prevent overheating.
  • Handle with care to avoid bending or damaging the aluminum components.

2. Package Contents

Please verify that all components are present in your package:

  • Aluminum alloy heat sink (Top Fin)
  • Stainless steel brushed base (Bottom Plate)
  • Thermal Conductive Silicone Pads (1.0mm thickness)
  • Heat sink screws (x4)
  • M.2 SSD (purchased separately)
Exploded view of JONSBO M.2 SSD Heatsink components
Figure 2.1: Exploded view of the JONSBO M.2 SSD Heatsink showing all included components.

Note: The M.2 SSD is not included and must be purchased separately.

3. Setup Instructions

Follow these steps carefully to install the JONSBO M.2 SSD Heatsink onto your M.2 2280 solid-state drive.

  1. Prepare the Bottom Plate: Tear off the thin protective film from one thermal pad and carefully stick it into the designated slot on the stainless steel brushed base (bottom plate).
  2. Position the SSD: Insert your M.2 SSD PCB into the card slot of the bottom plate, ensuring the SSD chip is flush against the thermal pad. Adjust the SSD's position so that its gold fingers and screw holes are exposed.
  3. Prepare the Top Fin: Tear off the thin protective film from the second thermal pad and stick it onto the inside surface of the aluminum alloy heat sink (top fin).
  4. Assemble the Heatsink: Carefully combine the top fin with the bottom plate, ensuring a tight fit.
  5. Secure the Assembly: After pressing the components together firmly, use the provided screws to fix the side screws, tightening them diagonally and evenly to avoid excessive force on one side.
  6. Install onto Motherboard: Insert the assembled M.2 SSD with the heatsink into the appropriate M.2 slot on your motherboard.
  7. Final Securement: Secure the M.2 SSD to the motherboard using the hard drive screw typically included with your motherboard.
Step-by-step installation diagram for JONSBO M.2 SSD Heatsink
Figure 3.1: Visual guide for heatsink installation and mounting onto the motherboard.

4. Operating Principles

The JONSBO M201/M202 M.2 SSD Heatsink is designed to effectively dissipate heat generated by high-performance M.2 SSDs, preventing thermal throttling and maintaining optimal drive performance.

  • Efficient Heat Transfer: The heatsink utilizes high-quality thermal conductive silicone pads to efficiently transfer heat from the SSD's controller and NAND chips to the aluminum alloy body.
  • Passive Cooling Design: The all-aluminum construction, featuring a grille-style fin design, maximizes the surface area for heat dissipation. This passive cooling method relies on natural convection to draw heat away from the SSD and into the surrounding air, ensuring smooth airflow and rapid heat dissipation.
  • Performance Preservation: By keeping the SSD's operating temperature within optimal limits, the heatsink prevents performance degradation, data transmission loss, and potential long-term damage caused by overheating during intensive read/write operations.
Grille style design of the heatsink for improved airflow
Figure 4.1: Grille style design promoting efficient heat dissipation through increased surface area and smooth airflow.
All-aluminum heatsink with thermal pad for superior heat conduction
Figure 4.2: Guided all-aluminum heatsink with high-quality thermal conductive silicone pad for effective heat transfer.

5. Maintenance

The JONSBO M.2 SSD Heatsink requires minimal maintenance to ensure continued performance.

  • Dust Removal: Periodically inspect the heatsink fins for dust accumulation. Use a can of compressed air or a soft brush to gently remove any dust, ensuring optimal airflow.
  • Thermal Pad Integrity: If you ever need to remove the heatsink, inspect the thermal pads for any damage or degradation. If they appear worn or torn, replace them with new thermal pads of appropriate thickness.
  • Environmental Conditions: Ensure your PC case has adequate airflow to assist the passive cooling of the heatsink.

6. Troubleshooting

If you encounter issues, refer to the following common problems and solutions:

Problem: Damaged SSD particles/controller after installation.
Possible Causes & Solutions:
  • Screws too tight or uneven force: Ensure screws are tightened diagonally and evenly, applying moderate force. Over-tightening can damage the SSD.
  • Silicone sheet too thick: Use the provided thermal pads or ensure replacement pads are of the correct thickness to avoid excessive pressure.
Problem: Heatsink buckle/bottom plate deformation or loose fit.
Possible Causes & Solutions:
  • Forceful bending: The aluminum material is soft. Avoid forcefully bending the heatsink components during installation or handling.
Problem: SSD temperature is higher than expected after heatsink installation.
Possible Causes & Solutions:
  • Protective film not removed: Ensure that the protective films on both sides of the thermal conductive silicone pads have been completely removed before installation.
  • Improper contact: Re-check installation steps to ensure the thermal pads make full and even contact with both the SSD chips and the heatsink surfaces.

7. Specifications

FeatureJONSBO M201JONSBO M202
TypeM.2 SSD Cooler
BrandJonsbo
MaterialAluminum Alloy (Heatsink), Stainless Steel (Base)
Dimensions (L x W x H)74.7 x 23.4 x 30 mm76.0 x 23.8 x 10.4 mm
Height above M.2 surface26.7 mm7 mm
WeightApprox. 0.1 kg
Applicable SSDM.2 2280 Solid State Drive (Single/Double-sided Particle)
Cooling MethodPassive Heat Dissipation
RGB SupportNo RGB
Power InterfaceNone (Passive)
Dimensional diagram for JONSBO M201 heatsink
Figure 7.1: JONSBO M201 Dimensional Specifications.
Dimensional diagram for JONSBO M202 heatsink
Figure 7.2: JONSBO M202 Dimensional Specifications.

8. User Tips

  • Remove Protective Films: Always ensure all protective films are removed from both sides of the thermal pads before assembly for effective heat transfer.
  • Gentle Handling: The aluminum components are designed for heat dissipation and can be delicate. Handle them gently to avoid deformation.
  • Even Screw Tightening: When securing the heatsink, tighten screws gradually in a diagonal pattern to ensure even pressure and prevent damage to the SSD or heatsink.
  • Case Airflow: While the heatsink is passive, good airflow within your PC case will significantly enhance its cooling performance.
  • Realistic Expectations: While effective, passive heatsinks provide a reduction in temperature rather than active cooling. For extreme workloads, monitor your SSD temperatures to ensure they remain within acceptable limits.

9. Warranty and Support

Warranty Information

The JONSBO M201/M202 M.2 SSD Heatsink comes with a 1-year warranty from the date of purchase. This warranty covers manufacturing defects under normal use. It does not cover damage resulting from misuse, accident, modification, or improper installation.

Customer Support

For any questions, technical assistance, or warranty claims, please contact your retailer or the official JONSBO support channel.

© 2024 JONSBO. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.