NEEWER TT560

Contents

Neewer TT560 Flash Speedlite User Manual

Model: TT560

1. Introduction

Thank you for purchasing the Neewer TT560 Flash Speedlite. This on-camera flash features a high-performance CPU control circuit for accurate power output, achieving a minimum flash power of 1/128. It includes an advanced light-controlled flash mode and an anti-pre-flash function, allowing compatibility with cameras that have pre-flash capabilities. Its controllable flash photography enables greater creative freedom.

Package Contents

  • TT560 Speedlite Flash
  • Storage Bag
  • Mini Stand
Package contents of Neewer TT560 Flash Speedlite, showing the flash unit, a storage bag, and a mini stand with dimensions.
Figure 1: Package Contents and Dimensions (Flash: 7.5cm x 19cm, Weight: 0.45kg)

2. Safety Precautions

  • Do not use the flash near chemicals, special substances, or flammable gases. These substances may react to the strong light emitted by the flash, causing fire or electromagnetic interference.
  • Avoid placing the product in environments exceeding 40 degrees Celsius (e.g., a car trunk), as this may damage components.
  • This product is not waterproof. Take precautions in rainy or humid environments.
  • Remove batteries when the unit is not in use for extended periods and store in a cool, dry place.
  • Do not expose this product to rain or moisture to avoid fire or electric shock. Contains high-voltage components; do not disassemble or repair the product yourself. If repair is needed, send it to a designated professional service center.
  • If the product is dropped or subjected to a strong impact, do not continue to use it if the casing is broken, to avoid contact with internal electronic components and potential electric shock.
  • Do not flash the flash head directly into human eyes (especially infants' eyes) at close range, as this may cause visual impairment. When photographing infants, ensure the flash is at least 1 meter away, or use bounce flash to reduce potential harm to vision.
  • Store batteries and small parts away from children to prevent accidental swallowing. If an object is swallowed, seek immediate medical attention.

3. Product Overview

Familiarize yourself with the components of your TT560 Flash Speedlite:

Diagram of the Neewer TT560 Flash Speedlite with labels for its various parts.
Figure 2: Flash Speedlite Components
  1. Built-in Wide Panel
  2. Reflection Board
  3. Flash Head
  4. Socket Cover
  5. Optic Control Sensor
  6. PC Sync Socket
  7. Lock Ring
  8. Hot Shoe Stand
  9. Dedicated Hot Shoe Contact
  10. Battery Cover
  11. Power Switch
  12. Charging Indicator
  13. Test Button
  14. Mode Select Indicator
  15. Output Level Indicator
  16. Flash Power Level Button
  17. Mode Select Button

4. Setup

4.1 Battery Installation

The TT560 Flash Speedlite uses 4x AA batteries (Alkaline or Ni-MH rechargeable batteries are usable).

  1. Open the battery cover by sliding it in the arrow direction and then opening it with your thumb.
  2. Insert the batteries according to the direction indicated by the sticker inside the battery holder. Ensure the positive (+) and negative (-) ends are correctly inserted.
  3. Close the battery cover by sliding it back into place along the arrow direction until it clicks, indicating it is locked.

Attention:

  • Take care when changing batteries after continuous flashes, as they may be hot.
  • Remove batteries when the unit is idle to prevent leakage that could damage the flash unit.

4.2 Mounting the Flash on the Camera

The TT560 is compatible with DSLR cameras that have electrical contacts on their hot shoe. Please confirm your camera model has electrical contacts before use.

Image showing compatible camera hot shoe with electrical contacts and incompatible hot shoe without electrical contacts.
Figure 3: Hot Shoe Compatibility
  1. Slide the flash mount fully into your camera's hot shoe socket.
  2. Tighten the knob on the flash holder until the flash is securely locked in place.
  3. To remove the flash, loosen the knob and slide the flash out of the hot shoe.
Neewer TT560 Flash Speedlite mounted on a DSLR camera, ready for use.
Figure 4: Flash mounted on a DSLR camera

5. Operation

5.1 Power Management

  • Turn the power switch to "ON". The charging indicator light will initially be dim while charging. After a few seconds, it will light up red, indicating the flash is ready for shooting.
  • To test the flash, press the "TEST" button. Remember to turn the power switch to "OFF" after use.
  • If the charging indicator light flashes with a cycle of 1 second, it indicates low battery power. Please replace the batteries.

5.2 Power Selection

The TT560 offers 8 levels of power output, indicated by 8 LEDs. Use the '+' and '-' buttons to adjust the power:

  • Press the '+' key to increase power gradually: 1/128 → 1/64 → 1/32 → 1/16 → 1/8 → 1/4 → 1/2 → 1/1.
  • Press the '-' key to decrease power.

5.3 Flash Modes

Press the MODE button to cycle through the available flash modes:

  • M Mode (Manual): The flash can be used on-camera or with a hot shoe trigger. Set the desired flash brightness and adjust your camera settings. The flash will fire synchronously with the camera's shutter signal.
  • S1 Mode (Optical Slave): Use as a secondary light for various lighting effects. The flash will trigger synchronously with the first flash of a main flash. This mode mimics a wireless flash trigger.
  • S2 Mode (Pre-flash Cancel Slave): Also for use as a secondary light. This mode ignores the pre-flash of a main flash and triggers synchronously with the second flash of the main flash, making it suitable for cameras with pre-flash functions.

Note:

  • In M mode, the flash light control triggering function is turned off.
  • In S1 and S2 modes, the hot shoe trigger function of the flash is disabled.

5.4 Shutter Synchronization Function

To trigger the flash in sync with the camera's shutter, connect the camera to the flash using a flash cable.

5.5 Power Saving Function

  • In M mode, the flash will automatically enter power-saving state after approximately 30 minutes of inactivity. Press any button to wake it up.
  • In wireless flash modes (S1 or S2), it will enter power-saving state after 60 minutes of inactivity. Press any button to wake it up.
  • In power-saving mode, the charging indicator light flashes every 3 seconds, while other lights are off.

6. Photography Tips

6.1 Reflective Photography

If direct flash light is too harsh, point the flash head towards a wall or ceiling. The light will reflect off the surface before illuminating your subject, reducing harsh shadows and creating a more natural, softer look.

6.2 Shooting with a Reflector

Pull out the built-in reflector and wide-angle diffuser from the flash head, then push the wide-angle diffuser back in. This technique creates a highlight in the subject's eyes, known as 'eye lights', making them more captivating. This effect is best achieved when the flash head is tilted appropriately.

6.3 Using the Wide-angle Diffuser

Pull out the wide-angle diffuser to expand the flash range. This results in a softer and more evenly spread flash effect.

Diagram illustrating the multi-angle rotation capabilities of the flash head, showing vertical rotation from 0-90 degrees and horizontal rotation from 0-270 degrees.
Figure 5: Multi-Angle Rotation for Flexible Lighting

7. Maintenance

7.1 Continuous Flash Protection

To prevent overheating and damage to the flash head, avoid performing more than 20 rapid flashes at 1/2 and 1/1 power. After 20 consecutive flashes, allow the flash to cool down for at least 30 minutes. If you continue to flash immediately after 20 consecutive flashes, the internal overheating prevention function may be damaged. If this occurs, the charging time will increase to approximately 10-25 seconds. Allow the flash to cool for about 10 minutes, and it will return to normal operation.

Continuous Flash Protection Correspondence Table

Power Times (approximate value)
1/1 20
1/2 30
1/4, 1/8 40
1/16, 1/32 60
1/64, 1/128 160

7.2 System Overheating Protection

If the internal system overheats due to overuse, the internal circuit will automatically shut down the power supply. Wait for the system temperature to drop (approximately 10 minutes), and the flash will return to normal.

8. Troubleshooting

  • Flash not firing: Ensure batteries are correctly installed and charged. Check that the power switch is ON. Verify the flash is securely mounted on the camera's hot shoe and that the camera has electrical contacts.
  • Flash overheating: If the flash becomes hot or charging time increases significantly after continuous use, allow it to cool down for at least 10-30 minutes, depending on usage intensity. Refer to the Continuous Flash Protection table.
  • Charging indicator flashing (every 1 or 3 seconds): This indicates low battery power. Replace or recharge the batteries.
  • Flash not compatible with camera: Ensure your camera has a standard hot shoe with electrical contacts. Note that the TT560 does not support TTL and is not compatible with certain Canon EOS Rebel models (SL3/250D, T7/1500D/2000D, T100/3000D/4000D) that lack electrical contacts.

9. Specifications

Feature Specification
Model TT560
Guide Number 38 (ISO 100, 35mm)
Flash Mode M, S1, S2
Vertical Rotation Angle 0-90 degrees
Horizontal Rotation Angle 0-270 degrees
Power Source 4x AA batteries (Alkaline or Ni-MH)
Lighting Times 100-1500 times (with alkaline batteries)
Recycle Time Approx. 0.1-5s (with alkaline batteries)
Color Temperature 5600K ± 200K
Flash Duration 1/300s - 1/20000s
Dimensions 190 x 75 x 55mm
Weight 0.45kg
High-speed synchronous (HSS) Yes
TTL No
Display No
Certification CE, RoHS

10. User Tips

  • Always confirm your camera model's hot shoe type and electrical contacts for compatibility before use.
  • For Sony cameras, ensure your model uses the Mi Hot Shoe for proper functionality.

11. Frequently Asked Questions (FAQ)

Q: Is the Neewer TT560 compatible with Canon R100?
A: The TT560 is compatible with Canon DSLR cameras that have electrical contacts on their hot shoe. However, it is explicitly NOT compatible with Canon EOS Rebel SL3/250D, Rebel T7/1500D/2000D, Rebel T100/3000D/4000D, which lack these contacts. Please check your Canon R100 for electrical contacts on its hot shoe.
Q: Is the Neewer TT560 compatible with Sony a6400?
A: Yes, the TT560 is compatible with Sony cameras using the Mi Hot Shoe, including models like a6000, a6300, and a6500. The Sony a6400 is generally compatible.

12. Warranty and Support

For warranty information, technical support, or service inquiries, please refer to the official Neewer website or contact your retailer. Keep your purchase receipt as proof of purchase.

A detailed user manual in PDF format is available for download: View User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.