ANYFAR RM-LX2522F

Contents

ANYFAR Wireless Carplay/Android Auto Smart Module User Manual

Model: RM-LX2522F

1. Introduction

Preface

Thank you for choosing this Intelligent Car Information System. Our product adds CarPlay and Android Auto to vehicles lacking these features, letting you use them for music, navigation, and more—all via your car's original screen. A seamless upgrade, it bridges your smartphone and in-car display, bringing familiar interfaces without altering your vehicle's factory setup. Easy to integrate, it enhances connectivity safely, turning your existing infotainment system into a smart, intuitive hub. Modernize your drive affordably, leveraging what your car already has.

Safety Precautions

  • Install only by qualified professionals to avoid damaging vehicle electrical systems.
  • Disconnect car battery before installation to prevent short circuits.
  • Ensure all connections are secure and insulated to avoid fire hazards.
  • Do not block airbags, driver visibility, or vehicle controls during installation.
  • Avoid modifying essential vehicle safety systems or wiring.
  • Operate connected devices only when parked; never distract from driving.
  • Regularly check for loose connections or overheating during use.
  • Stop using immediately if unusual smells, sounds, or malfunctions occur.
  • Ensure product usage complies with local traffic laws and regulations.
  • Keep product away from water, extreme temperatures, and direct sunlight when not in use.

2. Product Overview

Key Features

  • Apple CarPlay: Connects iPhones to car systems, mirroring key apps for navigation, music, calls, and messages via screen or voice commands. Enables hands-free operation, syncing contacts and playlists, enhancing driving safety and convenience.
  • Android Auto: Connects Android phones to car displays, bringing essential apps safely. Access navigation, music, calls, and messages via voice or touch. Prioritizes driving-focused features for hands-free use, enhancing convenience and safety.
  • Front/Rear/360 Input: The intelligent module supports video decoding and can be equipped with frontview, rear view (with intelligent dynamic trajectory display and radar support), as well as a 360° panoramic view.

Wireless CarPlay Smart Module features
Figure 1: Wireless CarPlay Smart Module features including Bluetooth, CarPlay, Android Auto, Factory Protocol, Lossless Installation, Voice Control, Live Map, and Online Entertainment.

Compatibility

This module is designed for specific Land Rover and Jaguar models. Please verify your car's infotainment system type and screen size for compatibility.

Screen Type Identification:

  • Bosch System: The time is displayed in the upper right corner of the menu page. This system is generally compatible.
  • Harman System: The time is displayed in the middle of the menu page. This module is not compatible with Harman systems.

Bosch vs Harman system identification
Figure 2: Visual guide to distinguish between Bosch (compatible) and Harman (not compatible) infotainment systems based on time display location.

Compatibility guide for Land Rover/Jaguar
Figure 3: Compatibility guide showing screen styles (Bosch vs Harman) and OEM monitor details for Land Rover/Jaguar vehicles.

Compatible Model List (8-inch screens):

BrandCar ModelYearsScreen Size
Land RoverRange Rover Evoque2012-20168 inch
Range Rover2013-2016
Discovery 42012-2016
Discovery Sport2013-2016
Freelander 22011-2014
JaguarXE/XF2012-2014
XJL2012-2015
F-TYPE2013-2016

Compatible Model List for 8-inch screens
Figure 4: Table detailing compatible Land Rover and Jaguar models with 8-inch screens.

Compatible Model List (10.25-inch screens):

Car ModelYearScreen Size
E/F-PACE201910.25inch
XEL/XFL/XJL2016-201910.25inch
Discovery 52017-201810.25inch
Discovery Sport/Evoque201910.25inch
F-TYPE2017-201910.25inch

3. Setup

Installation Manual

Installation of this module requires technical expertise and disassembly of vehicle components. It is recommended that installation be performed by qualified professionals.

Note: Installation involves mounting a circuit board inside the car's screen, acting as a bridge to the CarPlay control module. This is not a simple plug-and-play process and requires confidence with torx drivers and car interior disassembly.

Main installation wiring diagram
Figure 5: Main installation wiring diagram showing connections between the ANYFAR module, factory LVDS harness, and factory power harnesses.

The product comes with three CAN-bus adapter harnesses. Choose the one that matches your vehicle model—preferably the connector behind the center-console A/C control panel. If the first two harnesses don't fit, use the main-unit connector located under the front passenger seat instead.

Module dimensions and cable types
Figure 6: Dimensions of the ANYFAR module and identification of included cables: Power cable, LVDS OUT, LVDS IN, RCA & USB cable.

LVDS connections on the module
Figure 7: Close-up of the ANYFAR module showing LVDS-IN and LVDS-OUT ports with connected cables.

Factory LVDS Harness connection
Figure 8: Diagram illustrating where the factory LVDS harness connects to the car's display and then to the ANYFAR module.

Connecting factory LVDS
Figure 9: Hand connecting the factory LVDS cable (pink connector) into the car's existing wiring.

Installation diagram from manual
Figure 10: Installation manual diagram showing connections from the head unit, original car fiber optic cable, factory power harness, and factory LVDS harness to the ANYFAR module and car display.

DIP Settings & Switch

The DIP switch settings are crucial for proper functionality based on your car model and screen size. Please adjust according to the table below.

Car ModelYearScreen SizeDIP Setting
E/F-PACE201910.25inch1347 ON
XEL/XFL/XJL2016-201910.25inch1257 ON
Discovery 52017-201810.25inch12347 ON
Discovery Sport/Evoque201910.25inch157 ON
F-TYPE2017-201910.25inch

Note: Please note that the dial is down to "ON". Since screen configuration cannot be obtained directly from the original system, we have provided all DIP options. Please try them one by one in order. After switching the DIP, be sure to restart the decoder for the changes to take effect.

4. Operating Instructions

Wireless Connection

The latest technology currently in use is a wireless CarPlay and Android Auto solution that supports audio and video separation. Before using the wireless connection, please pair your device via Bluetooth and ensure that the vehicle's audio system is set to Bluetooth music mode for optimal connection and audio performance.

Wireless CarPlay Connection Steps:

  1. Turn on your phone's Bluetooth and Wi-Fi, and keep them on.
  2. Go to Bluetooth settings on the Smart Box.
  3. Select the Bluetooth Device name as "CAR Audio_XXXX".
  4. Pair your phone and select "Use CarPlay" when prompted.

Wireless Android Auto Connection Steps:

  1. Turn on your phone's Bluetooth and Wi-Fi, and keep them on.
  2. Go to Bluetooth settings on the Smart Box.
  3. Select the Bluetooth Device name as "CAR Audio_XXXX".
  4. Pair your phone. After successful Bluetooth pairing, follow the on-screen Android Auto connection process.

Audio Source:

Please check on your iPhone whether the sound source is set to the original car radio for optimal audio output.

Control Functions

Control via Steering Wheel Buttons, Central Control Panel, and Touch Screen
Figure 11: Demonstrates how the module retains original car functions, allowing control via Steering Wheel Buttons, Central Control Panel, and Touch Screen.

Steering Wheel Button Control:

Button IconOperationFunction
📞Short pressAnswer the phone
☎️Short pressHang up the phone
⏭️Short pressNext song
⏮️Short pressPrevious song
+Short pressIncrease the volume
-Short pressDecrease the volume

Central Control Panel & Touch Screen Control:

Button/ActionOperationFunction
Power Button (on car display)Double ClickSwitch between OEM screen and interface screen (CarPlay/Android Auto)
Hazard Lights ButtonDouble ClickSwitch between OEM screen and interface screen (CarPlay/Android Auto)
Touch ScreenTouch/SwipeControl function within CarPlay/Android Auto interface

Switching between OEM and CarPlay/Android Auto
Figure 12: Diagram showing how to switch between OEM Car System and Apple CarPlay/Android Auto by long-pressing the "back" button on the car knob.

5. External Settings

Rear View Camera Input

This CarPlay interface supports camera input for clear rearview imagery. Connect the camera as per the guide below.

Rear view camera wiring diagram
Figure 13: Wiring diagram for connecting a rear view camera to the ANYFAR module.

Radar and Trajectory

If the aftermarket camera you are installing also supports the reversing trajectory line, please uncheck the A1 box in the MCU Setup to display the reversing trajectory line. The A2 box is for the aftermarket radar option; uncheck it to use it. If you want to connect the front camera, please choose the "A3" option.

MCU Setup for Radar and Trajectory
Figure 14: Screenshot of the MCU Setup menu for configuring radar and trajectory display.

6. User Tips

  • Installation Complexity: Be aware that installation is involved, requiring disassembly of the car interior and screen to mount a circuit board. Ensure you are confident with torx drivers and car electronics.
  • Time Commitment: A first-time installation might take around 3 hours. With familiarity, this can be significantly reduced.
  • Cable Management: Double-check that all cables are correct for your specific unit location (e.g., under seat vs. near screen) and fit properly. Some users reported issues with bent or incompatible cables.
  • Compatibility Verification: Carefully verify compatibility with your exact car model, year, and infotainment system (e.g., 10.25-inch InControl Touch). Incompatibility can lead to screen flickering or black screens.

7. Troubleshooting

Why will the Box's Bluetooth disconnect?

The working principle of wireless CarPlay involves Bluetooth for initial device information confirmation, after which a Wi-Fi connection is established to transmit data. To avoid interference, the Bluetooth connection will then disconnect. This is normal behavior.

I cannot connect CarPlay, but Bluetooth is already paired.

Please forget the device Bluetooth and reset Wi-Fi on your iPhone. Navigate to: Settings > General > Transfer or Reset [Device] > Reset > Reset Network Settings.

Why is the wireless CarPlay connection not stable?

  1. Ensure that the mounted position of the CarPlay box is not blocked by metal components, as this may impair Wi-Fi signal transmission.
  2. Switch the Wi-Fi channel. Enter the CarPlay box settings: Factory Mode > Connectivity Settings > Hotspot Band. Select channel 1, 6, or 11, depending on your current region, to find the most stable connection.

Compatibility Issues (Flickering/Black Screen)

  • If your screen flickers or goes black after installation, double-check compatibility with your specific car model, year, and infotainment system (e.g., 10.25-inch InControl Touch).
  • If cables do not fit or reach, ensure you have the correct kit for your unit's location (under seat vs. near screen) and contact support with photos for assistance.

8. Specifications

ParameterValueParameterValue
Operating voltage9-16V, 14.4V (rated)Storage temperature-30 ~ +85°C
Operating temperature-30 ~ +75°CAmbient humidity≤98% (at 45°C), 65±5% (rated)
Power consumption current1A (rated), 3A (Max)Shutdown currentCurrent: 300mA (Clock is on)
Quiescent currentless than 3mA
Charging current≤2A; when the USB charging current >1A, the host machine should activate the circuit protect function to control the current within 15A and avoid products burning.

9. Support

For technical assistance or any inquiries regarding your ANYFAR Wireless Carplay/Android Auto Smart Module, please contact our support team:

© 2024 ANYFAR. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.