Kunray 500W 25A Brushless Controller with LCD Display

Contents

Kunray 500W 25A Electric Bike Brushless Controller with LCD Display User Manual

For 36V/48V E-bikes and Scooters

1. Introduction

This manual provides comprehensive instructions for the installation, operation, and maintenance of your Kunray 500W 25A Electric Bike Brushless Controller and compatible LCD displays. Please read this manual carefully before use to ensure proper function and safety.

2. Safety Information

  • Always ensure the battery is disconnected before performing any installation or maintenance.
  • Incorrect wiring can damage the controller, display, or other components. Follow the wiring diagram precisely.
  • Ensure all connections are secure and waterproof where necessary.
  • Do not attempt to modify the controller or display. This may void the warranty and create safety hazards.
  • Keep the controller and display away from extreme temperatures and direct sunlight.
  • Some displays are IP65 rated (splash-proof) but are not submersible. Avoid submerging the display in water.

3. Package Contents

Your package should contain the following items:

  • Kunray 500W 25A Brushless DC Motor Controller
  • Selected LCD Display (e.g., S830U, S966, M5, etc.)
  • Associated wiring harnesses
  • Mounting hardware for display (if applicable)
Kunray 500W 25A Electric Bike Brushless Controller with various LCD displays
Overview of the Kunray 500W 25A Brushless Controller and various compatible LCD displays.

4. Specifications

4.1. 500W 25A Brushless DC Motor Controller

Dimensions of the 500W 25A controller
Dimensions of the 500W 25A controller: 125mm length, 50mm width, 30mm height.
ParameterValue
Rated Power500W
Rated Voltage36V/48V
Cutoff Voltage19/29/39V ±0.5
Current Output25A ±1A
Size125mm x 50mm x 30mm
WeightApproximately 250g (Note: Manual measurement may have 1-3mm error)
Mosfets9 mosfets
Brake InputLow-level

4.2. LCD Display Models (SM Connector)

Various display models are compatible. Ensure your chosen display uses the UART 2 protocol for optimal performance with this controller.

4.2.1. S830U Display

S830U LCD Display with dimensions and wiring
S830U LCD Display: Product shell ABS, Net weight 210g, Gear mode 1-5, Voltage rating 24/36/48V, Waterproof rating IP65. Dimensions: 90mm (height) x 54mm (width) x 22mm (mount diameter).
  • Product Name: S830
  • Product Shell: ABS
  • Net Weight: 210g
  • Gear Mode: 1-5
  • Voltage Rating: 24/36/48V
  • Waterproof Rating: IP65
  • Dimensions: 90mm x 54mm x 22mm
  • Features a USB charging port for mobile devices.

4.2.2. S966 Color LCD Display

S966 Color LCD Display with key interpretation
S966 Color LCD Display: Features Battery display, Speed display, Assist state & Light, Multifunctional display, Power Assist Status, Vehicle Mode display. Key interpretation for parameter setting, function selection, light on/off, power on/off, push forward, and PAS gear.
  • Voltage: 24/36/48/52/60/72V
  • Features: Power display, Speed display, Mileage display.
  • NFC Function: Keyless start and lock the display.

4.2.3. LED-G20 Display

LED-G20 Display with specifications
LED-G20 Display: IP65 rated (not submersible). Features Battery Level Indicator, Power Assist Level, On/Off Switch. Dimensions: 48mm x 50mm x 22.2mm. SM length 164.5cm, Weight 98.8g, Plug 5pin+2pin, Voltage 36V/48V.
  • Model: LED-G20
  • Operating Temperature: -20~70°C
  • Dimensions: 48mm x 50mm x 22.2mm
  • SM Length: 164.5cm / 64.8in
  • Weight: 98.8g
  • Plug: 5pin+2pin
  • Voltage: 36V/48V
  • Waterproof Rating: IP65 (Not Submersible)

4.2.4. EN06 Display

EN06 Display with specifications and USB charging port
EN06 Display: Features USB charging port. Dimensions: 60mm x 46mm x 22.2mm. SM length 167cm, Weight 87g, Plug 5pin, Voltage 24V-48V.
  • Model: EN06
  • Operating Temperature: -20~60°C
  • Dimensions: 60mm x 46mm x 22.2mm
  • SM Length: 167cm / 65.74in
  • Weight: 87g
  • Plug: 5pin
  • Voltage: 24V-48V
  • Features a USB charging port.

4.2.5. M5 Display

M5 Display with specifications
M5 Display: Features Power display, Speed display, Mileage display. Line length 1685mm, Plug 5 pin SM plug.
  • Line Length: 1685mm
  • Plug: 5 pin SM plug
  • Features: Stable performance, accurate and sensitive, quality assurance, intimate service.
  • Full screen backlight for day and night visibility.

4.2.6. M9 Display

M9 Display with specifications
M9 Display: IP65 rated (not submersible). Dimensions: 111mm x 63mm x 22.2mm. SM length 163.5cm, Weight 268g, Plug 5pin+2pin, Voltage 24V-72V.
  • Model: LCD-M9
  • Operating Temperature: -20~70°C
  • Dimensions: 111mm x 63mm x 22.2mm
  • SM Length: 163.5cm / 64.37in
  • Weight: 268g
  • Plug: 5pin+2pin
  • Voltage: 24V-72V
  • Waterproof Rating: IP65 (Not Submersible)

4.2.7. UKC1 Color LCD Display

UKC1 Color LCD Display with USB charging port
UKC1 Color LCD Display: Features USB charging port (5V 500mA). Voltage: 24/36/48/52/60/72V. Displays RT Speed, TRIP, ODO, ASSIST, POW, CLK.
  • Voltage: 24/36/48/52/60/72V
  • Features: Power display, Speed display, Mileage display.
  • USB Charging Port: 5V 500mA.

4.2.8. S800 LED Display

S800 LED Display with dimensions and functions
S800 LED Display: Horn light double in one, bifunctional, double button, waterproof. Dimensions: 80mm (length) x 40mm (width) x 22.2mm (mount diameter). Functions include Data Display, Intelligent Power, Stalls Setting, Parameter Setting, Data View, Vehicle Boosting, Cruise And Constant Speed, Night Driving, Password Setting, Automatically Prompt.
  • Features: Horn light double in one, bifunctional, double button, waterproof.
  • Dimensions: 80mm x 40mm x 22.2mm.
  • Functions: Data Display, Intelligent Power, Stalls Setting, Parameter Setting, Data View, Vehicle Boosting, Cruise And Constant Speed, Night Driving, Password Setting, Automatically Prompt.

4.2.9. S866 Display

S866 Monochrome and Color Displays with specifications
S866 Display: Available in Monochrome and Color versions. Dimensions: 80.5mm x 47.5mm. SM Length 1700mm, Material Plastic, Weight 200g, Plug 5Pin Female SM Plug, Voltage 24V, 36V, 48V. Holder Diameter: φ22mm.
  • Type: LCD S866 Display (Monochrome and Color options)
  • Dimensions: 80.5mm x 47.5mm
  • SM Length: 1700mm
  • Material: Plastic
  • Weight: 200g
  • Plug: 5Pin Female SM Plug
  • Voltage: 24V, 36V, 48V
  • Holder Diameter: φ22mm

4.2.10. UKS6 Color LCD Display

UKS6 Color LCD Display
UKS6 Color LCD Display: Voltage 24V-72V. Features Power display, Speed display, Mileage display.
  • Voltage: 24V-72V
  • Features: Power display, Speed display, Mileage display.

4.2.11. S869 LCD Display

S869 LCD Display
S869 LCD Display: Features Battery Indicator, Assist gear, Speed, Single Mileage/Total mileage. Built-in intelligent chip, integrated gear switching, real-time cycling data, heart backlight design.
  • Features: Battery Indicator, Assist gear, Speed, Single Mileage/Total mileage.
  • Built-in intelligent chip, integrated gear switching, real-time cycling data, heart backlight design.

5. Installation and Wiring

Proper installation is crucial for the safe and correct operation of your e-bike system. Refer to the wiring diagram below and follow the steps carefully.

Wiring diagram for Kunray 500W 25A Brushless Controller
Detailed wiring diagram for the 500W 25A Brushless Controller. Connections include Battery+-, Self study, PAS sensor, Headlight power, Throttle, Brake, Hall, Display, and Motor phase.

5.1. Controller Wiring Connections

  1. Battery Power (XT60 Connector): Connect the XT60 connector from the controller to your e-bike battery. Ensure correct polarity (Battery+-).
  2. Motor Phase Wires: Connect the three thick wires from the controller to the corresponding motor phase wires.
  3. Hall Sensor Wires: Connect the Hall sensor wires from the controller to the motor's Hall sensor wires.
  4. Display Connection: Connect the display cable from the controller to your LCD display.
  5. Throttle: Connect the throttle cable to the controller.
  6. Brake Levers: Connect the brake lever cables to the controller.
  7. PAS Sensor: Connect the Pedal Assist System (PAS) sensor cable to the controller.
  8. Headlight Power: Connect your headlight (Black: GND, Yellow: Power+).
  9. Self-Study Wires: These are typically two white wires. Connect them together briefly for initial motor learning, then disconnect.

Important: Always double-check all connections before powering on the system. Incorrect wiring can cause damage.

5.2. Display Installation

Mount the display securely on your handlebars using the provided bracket. Ensure it is positioned for easy viewing and access to buttons while riding.

Product installation diagram for a display
General product installation showing display mounting on handlebars.

6. Operating Instructions

6.1. General Display Operation (Example: S966)

S966 Color LCD Display key interpretation
Key interpretation for S966 display: Parameter setting, function selection, light on/off, power on/off, push forward, and PAS gear.
  • Power On/Off: Long press the 'M' key for 3 seconds.
  • Light On/Off: Long press '+' key for 3 seconds.
  • PAS Gear Selection: Short press '+' or '-' keys.
  • Push Forward Mode: Long press '-' key for 3 seconds.
  • Function Selection: Short press 'M' key.
  • Parameter Setting: Long press '+' and 'M' keys simultaneously.

6.2. NFC Function (S966-NFC, GD02, UKC1)

Some displays, like the S966-NFC, GD02, and UKC1, feature an NFC function for keyless start and locking.

S966-NFC display open ways: NFC card, password, mobile phone
S966-NFC Open Ways: Power on by tapping an NFC card twice, entering a password (e.g., 2023), or using NFC on a mobile phone.
  1. NFC Card: Turn on the power and tap the screen twice with the NFC card to turn it on/off.
  2. Password: After turning on the power, briefly press the up or down key and enter the default password (e.g., 2023) to open it.
  3. Mobile Phone: After copying the card using NFC on your phone, the display panel can be opened through the phone.

6.3. USB Charging Port (S830U, EN06, UKC1)

Displays like S830U, EN06, and UKC1 include a USB charging port for convenient mobile phone charging (5V 500mA output for UKC1).

UKC1 Color LCD Display showing USB charging a phone
UKC1 Color LCD Display with USB charging port, providing 5V 500mA output.
Video demonstrating the NFC keyless start function on the S966-NFC display.

7. Maintenance

  • Regularly check all electrical connections for tightness and corrosion.
  • Keep the controller and display clean and dry. Wipe with a soft, damp cloth. Do not use harsh chemicals.
  • Avoid exposing the components to heavy rain or water immersion, especially for displays not rated for full waterproofing.
  • Inspect wiring for any signs of wear or damage. Replace damaged wires immediately.

8. Troubleshooting

ProblemPossible CauseSolution
Display not turning onLoose power connection, battery low, display fault.Check battery connection and charge level. Ensure display cable is securely connected. If using NFC, ensure card is tapped correctly.
Motor not respondingLoose motor phase/Hall sensor wires, throttle issue, controller fault.Verify all motor and Hall sensor connections. Check throttle cable. Perform self-study if applicable.
Inaccurate speed/mileageIncorrect wheel diameter setting in display parameters.Access display settings (refer to specific display manual) and adjust wheel diameter.
Error code on displaySystem malfunction.Refer to your specific display's manual for error code interpretations and solutions. Common issues include motor, Hall sensor, or brake faults.

9. User Tips

  • Compatibility: Always ensure your display and controller are compatible, especially regarding communication protocols (e.g., UART 2). It's recommended to purchase them together.
  • Battery Voltage: Double-check that the motor's voltage matches your battery's voltage to prevent damage.
  • Wiring: Take your time with wiring. A clear wiring diagram is provided; follow it meticulously.
  • PDF Manual: A detailed user manual in PDF format is available for download. It contains additional information and specific details for various display models. View User Manual (PDF)

10. Warranty and Support

The motor comes with a one-year warranty period. Accessories have a three-month warranty for quality problems, with free replacement. If the product is damaged or parts are lost in transit, the seller will take full responsibility.

For any questions or support, please contact the seller directly. They will assist you in resolving any issues.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.