UKGF USB BBS36 BBS48 BBS52 Battery

Contents

UKGF Hailong E-Bike Battery User Manual

Model: USB BBS36 BBS48 BBS52 Battery

Brand: UKGF

1. Introduction

Thank you for choosing the UKGF Hailong E-Bike Battery. This manual provides essential information for the safe and efficient use, installation, and maintenance of your new battery. Please read this manual thoroughly before using the battery and keep it for future reference.

This battery is designed for electric bicycles and scooters, offering reliable power with various voltage and capacity options. It features an integrated Battery Management System (BMS) for optimal performance and safety.

2. Safety Instructions

Always follow these safety guidelines to prevent injury or damage to the battery and your e-bike:

  • Do not immerse the battery in water or expose it to extreme moisture.
  • Keep the battery away from heat sources, open flames, and direct sunlight.
  • Do not short-circuit the battery terminals.
  • Do not disassemble, crush, or puncture the battery.
  • Use only the charger provided or a charger specifically approved for this battery.
  • Keep the battery out of reach of children.
  • If the battery emits an odor, generates heat, changes color, or appears abnormal during use or charging, discontinue use immediately and contact support.
  • Avoid dropping the battery or subjecting it to strong impacts.
  • Do not connect the battery in reverse polarity.
  • Ensure the battery is securely mounted to prevent it from falling during operation.

3. Package Contents

Please check the package for the following items:

  • 1 x UKGF Hailong E-Bike Battery (selected voltage and capacity)
  • 1 x Battery Install Plate
  • 1 x Charger (US/EU/AU/UK plug type)
  • 1 x Motor Battery Connection Cable (XT60 or T-plug, depending on selection)
  • 2 x Keys for Anti-theft Lock

4. Setup & Installation

Follow these steps to install your battery onto your electric bicycle:

  1. Attach the Battery Base: Securely mount the battery install plate (base) to your e-bike's down tube using appropriate screws and tools. Ensure it is firmly attached and does not wobble.
  2. Slide the Battery On: Align the battery with the installed base plate and slide it into place until it clicks securely.
  3. Lock the Battery: Use the provided key to lock the battery onto the base plate. This prevents theft and ensures the battery remains in place during riding.
  4. Connect to Motor: Connect the battery's discharge cable (XT60 or T-plug) to your e-bike's motor controller. Ensure the connection is firm and secure.
Battery Installation Steps
Figure 1: Battery Installation Steps. Step 1: Attach the battery base to the bike frame. Step 2: Slide the battery onto the base. Step 3: Lock the battery with the key.

5. Operating Instructions

5.1. Product Functions Overview

Product Functions
Figure 2: Product Functions. Includes Power indicator, USB port, ON/OFF switch, Anti-theft Lock, XLR charging port, and Customized discharge port.

5.2. Charging the Battery

Before first use, fully charge the battery. Always use the provided charger.

  1. Ensure the battery is turned off.
  2. Connect the charger's output plug to the battery's XLR charging port.
  3. Plug the charger into a standard AC power outlet.
  4. The charger's indicator light will typically show red during charging and turn green when fully charged.
  5. Once fully charged, disconnect the charger from the battery and then from the power outlet.

Note: The battery supports various charging head types. The default universal plug is typically number 4 (DC head).

Battery with Charger and Charging Heads
Figure 3: Battery with included charger and various charging head options.

5.3. Power On/Off

Locate the ON/OFF switch on the battery. Press it to turn the battery on or off. Ensure the battery is on before operating your e-bike.

5.4. Power Indicator

The battery features LED power indicators to show the remaining charge level. Press the button next to the LEDs to check the current charge status. Typically, more lit LEDs indicate a higher charge.

5.5. USB Port

A USB port is integrated into the battery, allowing you to charge external devices like smartphones while on the go.

5.6. Anti-theft Lock

Use the provided keys to lock the battery to its mounting plate. Turn the key to secure or release the battery.

5.7. Product Features Demonstration

Video 1: Demonstration of battery features including power indicator, lock mechanism, USB port, and charging port.

6. Maintenance

  • Cleaning: Wipe the battery with a soft, dry cloth. Do not use water or other liquids directly on the battery.
  • Storage: If storing the battery for an extended period, ensure it is charged to about 50-60% capacity. Store it in a cool, dry place, away from direct sunlight and extreme temperatures. Recommended storage temperature: -20°C to 35°C.
  • Charging Frequency: For long-term storage, check the battery charge every 2-3 months and recharge to 50-60% if necessary.
  • Temperature: Avoid operating or charging the battery in temperatures below -15°C or above 65°C.
  • Cycle Life: The battery is designed for more than 1000 charging cycles without significant capacity loss. After approximately 300 cycles, the capacity may reduce to 80% of its original rating.

7. Troubleshooting

If you encounter issues with your battery, refer to the following common problems and solutions:

ProblemPossible CauseSolution
Battery not chargingCharger not connected properly; Charger malfunction; Battery BMS protection activated.Check all connections; Try another outlet; If charger is faulty, replace it; Contact support if BMS is suspected.
E-bike not powering onBattery turned off; Low battery charge; Loose connection to motor; Battery BMS protection activated.Turn battery on; Charge battery fully; Check motor connections; Contact support.
Battery power drops quicklyOver-discharge; Aging battery; Extreme cold weather.Avoid deep discharges; Battery may need replacement if old; Operate in recommended temperature range.
Battery gets hot during use/chargingOverload; Internal short circuit; Faulty charger.Reduce load on e-bike; Discontinue use immediately and contact support.

7.1. BMS Protection Features

Your battery is equipped with an advanced Battery Management System (BMS) that provides multiple layers of protection:

  • Over Voltage Protect: Prevents overcharging.
  • Over Discharge Protect: Prevents excessive discharge that can damage cells.
  • Over Charge Protect: Ensures safe charging levels.
  • Over Current Protect: Protects against excessive current draw.
  • Temperature Protect: Monitors and protects against extreme temperatures.
  • Balance Protect: Balances cell voltages for optimal performance and longevity.
BMS Protection Features
Figure 4: BMS Protection Features for battery safety and longevity.

8. Specifications

The UKGF Hailong E-Bike Battery is available in various configurations. Please refer to the specifications for your specific model:

Feature36V Models48V Models52V Models
Nominal Voltage36V48V52V
Nominal Capacity12Ah, 20Ah, 30Ah12Ah, 20Ah, 30Ah12Ah, 20Ah, 30Ah
Battery Cell TypeA+ 18650/21700
Battery Size (L*W*H)360mm * 90mm * 110mm
Max Constant Discharge Current25A30A
Peak Current60A
Charge Voltage42V54.6V58.8V
Discharge Cut-off Voltage28V36.4V39.2V
Cycle Life>1000 times (to 80% capacity after 300 cycles)
Charge Temperature-15°C to 65°C (Recommended 0°C to 45°C)
Discharge Temperature-15°C to 65°C (Recommended -20°C to 60°C)
Protection FunctionOver charge, Over discharge, Over current, Short circuit, Balance
Battery Overview Specifications
Figure 5: Detailed Battery Overview and Specifications.

9. User Tips

  • Pre-shipment Confirmation: Some sellers may contact you to confirm battery style and size for compatibility. This is a good practice to ensure you receive the correct battery for your e-bike.
  • Included Accessories: Check if the battery package includes a charger and additional power cords, as these can add significant value.
  • Performance Testing: After installation, perform test rides to evaluate the battery's range and performance. Many users report good results for distances of 50 kilometers or more.
  • Plug and Play: The battery is designed to be compatible and easy to install, often described as 'plug and play' with existing e-bike models.
  • Cost-Effectiveness: Users often find these batteries to be cost-effective, offering good performance for the price.

10. Warranty & Support

Your UKGF Hailong E-Bike Battery comes with a 12-month warranty from the date of purchase. This warranty covers manufacturing defects and malfunctions under normal use.

For any issues, questions, or support needs, please contact your seller or the manufacturer's customer service. When contacting support, please provide your purchase details and battery model information.

Customer Service and Warranty
Figure 6: Customer Service and Warranty Information. Includes 24-hour message reply, customized service, and 12-month warranty.

11. Battery Disposal

Do not dispose of the battery with household waste. Lithium-ion batteries contain materials that can be harmful to the environment if not disposed of properly. Please recycle the battery at an authorized recycling facility or return it to your dealer for proper disposal.

© 2025 UKGF. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.