1. Important Safety Information
Please read all instructions carefully before installation and use. Failure to follow these instructions may result in property damage or personal injury.
- Always wear appropriate safety gear during installation.
- Ensure the vehicle is clean and free of debris before installation.
- Do not overtighten screws or clamps, as this may damage the windshield or vehicle.
- Verify proper fitment and security of the windshield before operating the vehicle.
2. Product Information
The KEMIMOTO Rear Full Windshield is designed to provide protection and enhance the riding experience for compatible CFMOTO ZFORCE models. Made from hard-coated polycarbonate, it offers superior durability and clarity.
2.1 Package Contents
Verify that all parts are present before beginning installation.
| Item | Quantity |
|---|---|
| Upper Part of Windshield | 1 |
| Lower Part of Windshield | 1 |
| Foam Pad | 1 |
| M6*25 Screw | 4 |
| M6 Washer | 4 |
| M6 Flange Nut | 4 |
| M6 Wrench | 1 |
| Clamp | 6 |
The windshield measures approximately 44.89 inches (114 cm) in width and 25.79 inches (65.5 cm) in height.
3. Installation Instructions
Please read the installation instructions carefully before you start. For your safety and to ensure a satisfactory installation, please complete all the installation steps in the order shown below.
- **Prepare the Windshield:** Peel off the protective film from both the front and back surfaces of the upper and lower windshield parts.
- **Assemble Windshield Sections:**
Note: You will need to drill four holes on the foam pad to allow the M6*25 screws to pass through.
Place the foam pad between the upper part of the windshield (1) and the lower part of the windshield (2). Secure them together using the four M6*25 screws (4), four M6 washers (5), and four M6 flange nuts (6).
Figure 8: Foam Pad Placement - **Remove Factory Roof (if applicable):** Carefully remove the original factory roof of your UTV.
- **Position and Secure Windshield:**
Place the assembled windshield onto your UTV. Insert the six clamps (8) into the six designated slots on the upper windshield part. Wrap the clamps tightly around the UTV's roll cages to securely fix the windshield in place.
- **Final Steps:** Reinstall the factory roof (if removed) and ensure all components are securely fastened.
For a visual guide and detailed diagrams, please refer to the official user manual PDF: KEMIMOTO Rear Full Windshield User Manual (PDF).
4. Operating and Features
The KEMIMOTO Rear Full Windshield is designed to enhance your UTV experience with several key features:
4.1 Year-Round Protection
This windshield provides effective protection against various elements, keeping the UTV interior dry and clean. It prevents wind, leaves, dust, and debris from entering the cabin, ensuring a more comfortable ride in all seasons.
4.2 Enhanced Durability and Safety
Constructed from hard-coated polycarbonate, the windshield offers exceptional strength and impact resistance. It is 250 times stronger than glass and 20 times stronger than PMMA (acrylic), making it highly resistant to impacts from flying rocks, branches, and debris encountered during off-road driving.
4.3 Optimal Visibility and UV Protection
The windshield boasts a light transmittance of over 88%, ensuring clear vision and improving driving safety. Additionally, it features strong UV resistance with 0% UV transmittance, protecting occupants from harmful sun exposure.
4.4 Noise Reduction
The firmly mounting clips and integrated seal effectively isolate external noise, providing a quieter and more comfortable riding experience, even at high speeds.
5. Maintenance
To ensure the longevity and clarity of your KEMIMOTO Rear Full Windshield, follow these maintenance guidelines:
- **Cleaning:** Use a soft cloth or sponge with mild soap and water to clean the windshield. Avoid abrasive cleaners, harsh chemicals, or stiff brushes, as these can scratch the hard coating.
- **Drying:** Gently dry the windshield with a clean, soft microfiber cloth to prevent water spots.
- **Inspection:** Periodically inspect the windshield and mounting hardware for any signs of wear, damage, or looseness. Tighten any loose fasteners as needed.
- **Storage:** When not in use for extended periods, store the UTV in a covered area to protect the windshield from prolonged exposure to harsh weather conditions.
6. Troubleshooting
If you encounter any issues with your KEMIMOTO Rear Full Windshield, consider the following common troubleshooting steps:
- **Poor Fitment:** Double-check the compatibility list to ensure the windshield is designed for your specific UTV model and year. Re-examine the installation steps to ensure all parts are correctly aligned and secured.
- **Vibration or Rattling:** Ensure all clamps and screws are tightened securely. The foam pad should be correctly positioned between the windshield sections to reduce vibration.
- **Reduced Visibility:** Clean the windshield thoroughly using the recommended cleaning methods. If scratches are present, they may affect visibility.
- **Wind or Debris Leakage:** Verify that the rubber strip and foam pad are properly seated and that the clamps are tightly secured to create a good seal against the roll cage.
If problems persist, please contact KEMIMOTO customer support for further assistance.
7. Specifications
| Feature | Detail |
|---|---|
| Item Type | Rear Full Windshield |
| Material | Hard-coated Polycarbonate (PC) |
| Thickness | 5 mm |
| Color Options | Clear, Tinted |
| Dimensions (Approx.) | Width: 44.89 inches (114 cm), Height: 25.79 inches (65.5 cm) |
| Item Weight | 6.35 kg (14 lbs) |
| Light Transmittance | > 88% |
| Impact Resistance | 250x stronger than glass, 20x stronger than PMMA |
| UV Resistance | 0% UV transmittance |
| Special Features | Windproof, Noise Reduction, Scratch Resistant, Corrosion Resistant, Stretching Resistant |
7.1 Compatibility
This rear full windshield is compatible with the following CFMOTO ZFORCE models:
- ZFORCE 950 SPORT 2020-2022
- ZFORCE 950 H.O. SPORT 2022+
- ZFORCE 950 H.O. EX 2022+
- ZFORCE 1000 SPORT 2022+
It is a replacement for part number 5BYV-805300-1000.
Note: This product is NOT compatible with ZFORCE 950 Sport/ZFORCE 950 Trail/ZFORCE 800 Trail 2023-2024 models.
8. User Tips
- **Pre-Installation Check:** Before starting, ensure all parts are accounted for and the vehicle's roll cage area is clean.
- **Ease of Assembly:** The design, including pre-installed rubber strips, aims for straightforward assembly. Follow the steps sequentially for best results.
- **Verify Fit:** After installation, double-check that the windshield fits perfectly and securely to prevent rattling or gaps during operation.
9. Frequently Asked Questions (FAQ)
- Q: How can I ensure the product fits my vehicle?
- A: Please refer to the "7.1 Compatibility" section above to verify if your CFMOTO ZFORCE model and year are listed as compatible. If your model is not listed or is specifically mentioned as incompatible, this windshield will not fit.
10. Warranty and Support
For information regarding product warranty, returns, or technical support, please contact the seller directly through your purchase platform. Keep your order details handy for faster service.
This item is not a licensed product of Honda, Yamaha, Polaris, Can-Am, Kawasaki, CF Moto, or BRP. KEMIMOTO is an independent brand. Any references to third-party trademarks are for compatibility identification only.
