GODIAG GT107+

Contents

GODIAG GT107+ ECU Prog Adapter and DSG Gearbox Universal Jumper User Manual

1. Introduction

The GODIAG GT107+ DSG Plus Gearbox Data Adapter is a specialized tool designed for automotive maintenance engineers. It facilitates the connection to DSG gearbox Electronic Control Units (ECUs) for various tasks including cloning, diagnosis, repair, and data manipulation. This adapter supports reading, writing, and adjusting data for DSG gearbox ECUs using software such as PCMFlash, PCMTuner, and Kessv2.

The GT107+ features both automatic and manual selection modes for PCMFlash software, allowing flexibility for data reading/writing and diagnostic operations. It also enables direct reading and writing of DSG gearbox data using car battery power, providing clear communication status during the process.

GODIAG GT107+ ECU Prog Adapter and DSG Gearbox Universal Jumper kit

Image: The GODIAG GT107+ ECU Prog Adapter and DSG Gearbox Universal Jumper kit, showing the main adapter unit, the DSG adapter cable, and a probe.

2. Safety Information

Please read and understand all safety instructions before using the GODIAG GT107+ adapter. Failure to follow these instructions may result in electric shock, fire, or serious injury.

  • Always ensure the device is connected correctly according to the wiring diagrams provided. Incorrect wiring can damage the ECU or the adapter.
  • Do not operate the device in wet conditions or expose it to water.
  • Use only the specified power supply (12V 2A DC) or vehicle battery for operation.
  • Avoid touching exposed wires or connectors while the device is powered on.
  • Keep the device away from children and unauthorized personnel.
  • If any unusual behavior (e.g., smoke, strong odor, excessive heat) is observed, immediately disconnect power and cease operation.

3. Package Contents

Verify that all items listed below are included in your package:

  • 1pc x Godiag GT107+ ECU Prog AD
  • 1pc x DB9 DSG Gearbox Universal Conversion Jumper
  • 1pc x Power Cord with Battery Clips
  • 1pc x Probe
  • 1pc x DC power adapter (5.5*2.1mm female to 5.5*2.5mm male)
  • 1pc x Manual (PDF version available online)
GODIAG GT107+ package contents

Image: Contents of the GODIAG GT107+ package, including the adapter, cables, and accessories.

4. Product Features

The GODIAG GT107+ offers a range of features designed for efficient and safe ECU programming and diagnosis:

  • Wide Compatibility: Suitable for connecting VAG series gearbox ECUs, supporting models such as DQ250, DQ200, VL381, VL300, DQ500, DL501, as well as Benz and BMW ECUs.
  • Voltage Display: Provides real-time display of the current operating voltage of the gearbox ECU. A severe voltage drop can indicate a short circuit or incorrect wiring.
  • Current Display: Shows the current working current of the gearbox ECU, useful for assessing the ECU's operational status.
  • Communication Indicator: Displays the CANbus K-Line communication status, helping to determine if diagnostic programming is functioning correctly.
  • Analog Ignition Switch: Features a manual and automatic power switch, along with a 120 ohm switch.
  • Detachable DB9 Interface: Gold-plated DB9 connection interface allows users to create custom connection ports for DIY development.
  • Flexible Power Supply: Equipped with a power cord that includes battery clips, enabling power draw directly from the vehicle battery.
GODIAG GT107+ detailed view with labels and pinout diagrams

Image: Detailed view of the GODIAG GT107+ adapter with labels for its components and pinout diagrams for DQ200, DQ250, VL381, and DQ500.

5. Setup

5.1. GODIAG GT105 II ECU IMMO Prog AD (Optional Component)

The GODIAG GT105 II ECU IMMO Prog AD is an upgraded version of the GT105, offering additional functionalities that can be used in conjunction with the GT107+ for comprehensive diagnostic and programming tasks. Its features include:

  • Vehicle voltage display and alarm (for voltage below 11V).
  • Car remote control battery (CR2032) test.
  • TOYOTA steering angle matching and Lamborghini ID48 key IMMO auxiliary activation.
  • IMMO AD power adapter function for key programming (e.g., Ford all smart keys lost after 2016, with VVDI equipment).
  • Support for VAG 4th and 5th generation anti-theft, Toyota ECU synchronization, Mitsubishi all key lost matching, old Porsche Cayenne car IMMO key learning.
  • VPW, CANH, CANL, K-Line indicator lights to judge communication status.
  • On-site maintenance power supply (12V) from car battery for programming equipment (e.g., Xhorse Key Tool Plus Pad, VVDI Prog, CGDI Prog, IM608).
  • OBD Battery Replacement Tool for uninterruptible power supply during battery changes, preventing data loss.

5.2. General Connection Guidelines

Before connecting, ensure the vehicle's ignition is off and the adapter's function buttons are in the popped-up position (if applicable) before connecting the power supply.

  1. Identify the correct pinout for your specific gearbox ECU model. Refer to the pinout diagrams provided in this manual.
  2. Connect the DB9 DSG Gearbox Universal Conversion Jumper to the GODIAG GT107+ adapter.
  3. Carefully connect the wires from the DB9 jumper to the corresponding pins on the gearbox ECU according to the wiring definition.
  4. Connect the 12V 2A DC power adapter to the GT107+ or use the power cord with battery clips to draw power from the vehicle battery.

6. Operation

6.1. Using with PCMtuner (Bench Mode)

  1. Connect the Godiag GT107+ to the gearbox ECU (VAG DQ250, DQ200, VL381, VL300, DQ500, DL501, Renault DC0/DC4 Gen2, Honda LUK UDCT, etc.) according to the specific gearbox ECU wiring definition.
  2. Connect the 12V 2A DC power supply. Ensure function buttons are popped up before connecting power.
  3. Observe the GODIAG GT107+ analog ignition switch:
    • If not pressed (Auto mode), the voltage and current data displays 0V 0A.
    • If pressed (Manual mode), the adapter displays the current working voltage of the power supply and the current working current of the gearbox ECU.
    Note: Select 'Auto' or 'Manual' analog ignition mode based on the requirements of your data reading/writing software.
  4. Connect your PCMFlash, PCMTuner, or J2534passthru device to the GT107+.
  5. Perform data reading and writing operations using your software.

6.2. Using on the Car (OBD Mode)

  1. Connect the Godiag GT107+ to the gearbox ECU (VAG DQ250, DQ200, VL381, VL300, DQ500, DL501, Renault DC0/DC4 Gen2, Honda LUK UDCT, etc.) according to the specific gearbox ECU wiring definition.
  2. Connect the 12V 2A DC power supply. Ensure function buttons are popped up before connecting power.
  3. Observe the GODIAG GT107+ analog ignition switch:
    • If not pressed (Auto mode), the voltage and current data displays 0V 0A.
    • If pressed (Manual mode), the adapter displays the current working voltage of the power supply and the current working current of the gearbox ECU.
    Note: Select 'Auto' or 'Manual' analog ignition mode based on the requirements of your data reading/writing software.
  4. Connect your PCMFlash, PCMTuner, or J2534passthru device to the GT107+.
  5. Perform data reading and writing operations using your software.

6.3. Using with KESSV DQ200, DQ250, DQ500

  1. Connect the Godiag GT107+ to the gearbox ECU (VAG DQ250, DQ200, VL381, VL300, DQ500, DL501, Renault DC0/DC4 Gen2, Honda LUK UDCT, Benz, BMW, etc.) according to the specific gearbox ECU wiring definition.
  2. Connect the 12V 2A DC power supply. Ensure function buttons are popped up before connecting power.
  3. Press the GODIAG GT107+ analog ignition switch to put it in “manual” mode. The adapter will display the current working voltage of the power supply and the current working current of the gearbox ECU.
  4. Connect your OBD2 data reading/writing device or diagnostic device to the GT107+.
  5. Perform Gearbox ECU data reading, writing, or diagnostic operations.

7. Pinout Diagrams

Refer to the following diagrams for correct wiring connections to various DSG gearbox ECUs:

Pinout diagrams for DQ200, DQ250, VL381, DQ500

Image: Pinout diagrams for DQ200 (0AM, 0CW), DQ250 (02E, 0D9), VL381 (0AW), and DQ500 (0BT, 0BH) ECUs.

Pinout diagrams for DL382, DL501, DC0/DC4 Gen2, LuK-UDCT, V30, VL300

Image: Pinout diagrams for DL382 (0CK), DL501 (0B5), DC0/DC4 Gen2 (Renault), LuK-UDCT (Honda), V30 (01J), and VL300 (01J) ECUs, along with an example connection to a gearbox ECU.

8. Maintenance

  • Keep the adapter and cables clean and dry. Avoid exposure to dust, dirt, and moisture.
  • Store the device in its original packaging or a protective case when not in use to prevent damage.
  • Regularly inspect cables and connectors for any signs of wear, damage, or loose connections. Replace damaged components immediately.
  • Clean the gold-plated DB9 interface with a soft, dry cloth if necessary to ensure optimal conductivity.

9. Troubleshooting

  • No Power/Device Not Turning On:
    • Ensure the 12V 2A DC power adapter is securely connected and functioning, or that the battery clips are properly attached to a charged vehicle battery.
    • Check the DC power adapter for any damage.
  • Voltage Display Shows 0V 0A in Manual Mode:
    • Verify that the analog ignition switch is pressed down for manual mode.
    • Check all wiring connections to the gearbox ECU for correctness and ensure there are no short circuits. A severe voltage drop indicates a wiring issue.
  • No Communication with ECU:
    • Check the communication indicator lights on the GT107+. If they are not active, there might be a communication problem.
    • Ensure the correct pinout is used for your specific ECU model.
    • Verify that your diagnostic/programming software is correctly configured and compatible with the ECU and the GT107+.
    • Ensure the analog ignition mode (Auto/Manual) on the GT107+ matches the requirement of your software.
  • Software Errors During Read/Write:
    • Confirm that the software (PCMFlash, PCMTuner, Kessv2, etc.) is up-to-date and correctly installed.
    • Ensure the J2534passthru driver is installed and recognized by your computer.
    • Check for stable power supply during the entire operation.

10. Specifications

Attribute Value
Brand Name GODIAG
Model Name GODIAG GT107+
Function DSG Gearbox Data Adapter
Origin Mainland China
High-concerned chemical None
Is Batteries Included No
Product Length 15 cm
Product Width 5 cm
Product Height 5 cm
Product Weight 0.4 kg

11. User Tips

  • Check Connections Carefully: Some users have noted that screws on the plug where wires attach to the adapter might be slightly twisted upon arrival. Always double-check and tighten all connections to ensure proper contact and prevent issues during operation.
  • Verify Pinouts: Always confirm the correct pinout for your specific ECU model before making any connections. Refer to the provided diagrams and any additional documentation for your ECU.
  • Stable Power Supply: Ensure a stable 12V power supply throughout the entire programming or diagnostic process to avoid interruptions and potential data corruption.

12. Warranty & Support

For detailed warranty information and technical support, please refer to the official GODIAG documentation. A comprehensive user manual in PDF format is available for download and further reference. You can access the PDF manual here.

For any issues not covered in this manual, please contact your vendor or GODIAG customer support.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.