SWEVY SW-360

Contents

SWEVY Portable Phase Sequence Tester

Model: SW-360

3-Phase AC Rotation Meter, Voltage/Current Detector, Phase Rotation Indicator

Introduction

This manual provides instructions for the safe and effective use of the SWEVY SW-360 Portable Phase Sequence Tester. This device is designed for professional use in electrical systems to measure phase sequence, detect phase loss, and indicate phase rotation direction.

SWEVY LCD Phase Rotation Indicator SW-360 showing key features
Figure 1: SWEVY SW-360 LCD Phase Rotation Indicator highlighting Phase Sequence Measurement, Phase Loss Detection, Voltage: 40-600V, and Cable Length: 800mm.

Safety Information

WARNING: During testing, do not touch any test pencil on any phase or any bare metal probe to avoid electric shock.

Always adhere to local safety regulations and practices when working with electrical systems. Ensure the device is in good working condition before use.

Product Features

  • Convenient and practical design with a compact and aesthetically pleasing appearance.
  • Constructed with a durable and safe PC material shell.
  • Protection level: CATIII 600V.
  • Automatic low voltage reminder and automatic shutdown if there is no operation, conserving battery life.
SWEVY SW-360 showing wide voltage range and quiescent current
Figure 2: Device detail showing wide voltage range (40-600V) and low quiescent current (less than 3mA).

Product Components

The SWEVY SW-360 includes the main unit and three test clips. Refer to the diagram below for component identification:

Diagram of SWEVY SW-360 with numbered parts
Figure 3: Diagram of the SW-360 Phase Sequence Tester.
  1. Connecting wire for testing
  2. LCD display
  3. Phase sequence indicator
  4. Battery voltage status indicator
  5. Battery compartment
  6. Test clips

Setup

Battery Installation

The device requires three AAA batteries for operation. To install the batteries:

  1. Locate the battery compartment (5) on the back of the instrument.
  2. Open the battery compartment cover.
  3. Insert three AAA batteries, ensuring correct polarity.
  4. Close the battery compartment cover securely.

After battery installation, ensure the yellow, green, and red test clips (6) are reliably connected to the corresponding three-phase electrical terminals to be tested.

Operating Instructions

Once the batteries are installed and the test clips are connected to the three-phase electrical terminals, the device will automatically begin testing.

LCD Display Indications

LCD screen prompt examples for no input, low voltage, and phase loss
Figure 4: Examples of LCD screen prompts for various conditions. Note: This model does not have a backlight function.
  • No Input or Voltage Below 40V: The LCD will have no display.
  • Phase Loss Detection: If one of the three phases is missing, the LCD will display the corresponding phase loss, for example, "L.L.1", "L.L.2", or "L.L.3".
  • Clockwise Phase Rotation: When the phase sequence rotation direction is clockwise, the LCD will display "L.L.L" along with a clockwise arrow symbol.
  • Anti-Clockwise Phase Rotation: When the phase sequence rotation direction is anti-clockwise, the LCD will display "L.L.L" along with an anti-clockwise arrow symbol.

After Testing

After completing the testing, always disconnect the input terminals (test clips) from the testing terminals.

Maintenance

Battery Replacement

During testing, observe the battery voltage status indicator (4) on the LCD display. If a low voltage indicator appears, it signifies that the battery voltage is below the normal operating level. This can affect the instrument's function and measurement accuracy, and may even prevent the instrument from starting. In such cases, replace the three AAA batteries promptly.

General Care

  • Keep the instrument clean and dry.
  • Avoid exposing the device to extreme temperatures or humidity outside of its specified operating and storage environments.
  • Store the device in its carrying case when not in use to protect it from damage.

Troubleshooting

Problem Possible Cause Solution
LCD has no display No input voltage or voltage is below 40V. Batteries are dead or incorrectly installed. Ensure the device is connected to a three-phase system with voltage within 40-600V. Check and replace batteries if necessary.
Low voltage indicator appears Battery voltage is low. Replace all three AAA batteries.
Instrument fails to start Severely low battery voltage. Replace all three AAA batteries.
Incorrect phase sequence reading Improper connection of test clips. Ensure test clips are securely and correctly connected to the L1/A, L2/B, and L3/C phases.

Specifications

Characteristic Detail
Display Three-digit LCD display with 18mm text height
Sampling Rate 3 times/second
Operating Voltage Range 40-600V AC
Working Environment Temperature 0°C to +40°C
Working Environment Humidity 0-80% RH
Storage Environment Temperature -10°C to +60°C
Storage Environment Humidity 0-85% RH
Quiescent Current Less than 3mA
Power Supply Three (3) AAA batteries
Instrument Size (H×W×D) 116mm × 66mm × 26mm
Wire Length 800mm
Accessories 1 carrying case, 3 test clips
Certifications CE, RoHS

User Tips

  • Users have noted that the device performs as described, indicating reliable functionality for its intended purpose.

Warranty and Support

For detailed warranty information, technical support, or further inquiries, please refer to the official product documentation or contact SWEVY customer service.

A comprehensive user manual in PDF format is available for download: View User Manual (PDF).

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.