NJTY JD04

Contents

NJTY JD04 Infrared Thermometer User Manual

Model: JD04

1. Important Safety Information

Kindly Reminder: To avoid personal injury, please adhere to the following guidelines:

  • Do not point the laser at people or animals.
  • Children should not operate the infrared thermometer's laser.
  • Do not use the laser in explosive gas or other potentially explosive areas.
  • Keep the infrared thermometer away from high-temperature objects.
  • Electromagnetic fields from arc welders and induction heaters can affect test results.
  • Avoid using the laser on shiny or polished metal surfaces as temperature readings might be inaccurate and could cause burns.
  • The infrared thermometer measures surface temperature, not internal temperature; do not use it for body temperature measurement.
  • Steam, dust, and smoke can affect measurement accuracy.
  • Before use, check the casing for damage and do not use if damaged or missing parts.
  • Replace the battery when the battery icon appears on the display.
  • If the infrared thermometer malfunctions, do not use it; it may no longer be protective. For concerns, send the infrared thermometer for repair.
  • Allow 30 minutes for the infrared thermometer to stabilize if subjected to thermal shock due to significant temperature changes.
  • Remember that objects with high emissivity will have temperature readings lower than the actual temperature.
  • Failure to use the device as specified in this manual may impair the protective features of the equipment.

Note: This device emits Class 2 laser radiation. Use caution during operation. Do not look directly at the laser beam or observe it with optical instruments. Do not aim the laser at others or animals as laser radiation can damage your eyes.

2. Product Overview

The NJTY JD04 Infrared Thermometer uses non-contact infrared sensor technology to safely, accurately, quickly, and reliably measure target temperatures. It is widely used for measuring temperatures in industries such as machinery, chemicals, ceramics, light industry, food, metallurgy, power, and heat treatment.

Working Principle

Any object with a temperature above absolute zero emits infrared energy. This energy travels at the speed of light. The lens of the infrared thermometer collects and focuses the infrared energy onto a sensor. The sensor generates a low voltage output proportional to the target's temperature. This voltage is processed and displayed as a temperature reading.

NJTY JD04 Infrared Thermometer highlighting key features like sound switch, laser switch, temperature range, two-point laser, industrial/household use, adjustable emissivity, HD LCD/backlit display, and high/low temperature alarm.

Figure 2.1: Key Features of the NJTY JD04 Infrared Thermometer

3. Setup

3.1. Package Contents

Before starting, ensure all items are present in the package:

  • 1 x Infrared Thermometer
  • 1 x User Manual (this document and PDF)
  • 1 x Storage Bag
Package contents showing the infrared thermometer, user manual, and a storage bag.

Figure 3.1: NJTY JD04 Package Contents

3.2. Battery Installation

The thermometer uses a 9V (6F22) battery.

  1. Slide down the battery compartment cover located at the bottom of the handle.
  2. Connect the new 9V (6F22) battery to the battery clip, ensuring correct positive and negative polarity.
  3. Insert the battery into the compartment.
  4. Close the battery compartment cover.

Note:

  • If the instrument is not used for a long time, remove the batteries to prevent leakage.
  • If the low battery icon appears on the display screen, replace the batteries as soon as possible.

Video 3.2: Product demonstration including battery installation and various operational features.

4. Operating Instructions

4.1. Power-on and Basic Measurement

  1. Press the power button (J, refer to Figure 1 in the PDF manual) to turn on the thermometer.
  2. Aim the laser (K, refer to Figure 1 in the PDF manual) at the target to be measured. The device features two-point laser positioning for higher accuracy.
  3. For a single measurement, press and release the trigger. For continuous measurement, press and hold the trigger. (Note: For accurate single measurements, the trigger should be held for at least 0.5 seconds).
  4. The measured temperature value will appear on the backlit HD LCD display.
Infrared thermometer showing two laser points converging on a target, indicating precise positioning.

Figure 4.1: Two-point laser positioning for precise targeting.

Multiple views of the thermometer's HD LCD display from different angles, showing clear visibility.

Figure 4.2: HD LCD Display with clear visibility from various angles.

4.2. Button Functions and Display Symbols

The device features several buttons and display symbols for various functions:

  • Sound/SET Setting/+ Button: Single press to turn off the sound.
  • MODE Function Key: Short press to switch between MAX (Maximum), MIN (Minimum), DIF (Difference), AVG (Average), HAL (High Alarm), and LAL (Low Alarm) modes.
  • °C/°F/- Key: Short press to switch between Celsius (°C) and Fahrenheit (°F). In HAL/LAL mode, press SET to enter data setting.
  • Laser/Emissivity Adjustment Key: Short press to turn the laser on/off. Long press for about 3 seconds to enter Emissivity (EMS) adjustment mode.
  • Record Query/Clear Key (STO): Short press to view measurement history. Long press for about 3 seconds to clear all recorded values (if applicable to your model).
  • SCAN Symbol: Indicates the instrument is in testing status.
  • Laser Pointer Symbol: Indicates laser aiming is active.
  • Backlight Symbol: Indicates backlight is on.
  • Sound Symbol: Indicates the buzzer/voice prompt is on.
  • Low Battery Symbol: Appears when the battery is low.
  • HOLD Symbol: Indicates the measured temperature value is locked and held.

4.3. Setting High/Low Temperature Alarms (HAL/LAL)

  1. Press the MODE button to select either the "HAL" (High Alarm) or "LAL" (Low Alarm) symbol on the display.
  2. Press and hold the SET button for approximately 5 seconds until the first digit of the corresponding HAL or LAL setting value begins to flash.
  3. Use the + key to increase the value or the - key to decrease it.
  4. Press the MODE button to move to the next digit for adjustment.
  5. Repeat steps 3 and 4 to adjust all desired digits.
  6. Once adjustments are complete, press the MODE button to confirm.

Note:

  • If the thermometer continuously emits a "BiBi" sound during testing, check if the HAL or LAL setting values are too high or too low.
  • When the temperature exceeds the set HAL value or falls below the set LAL value, the buzzer will emit a continuous "BiBi" sound, and the respective HAL/LAL symbol will flash.

4.4. Adjusting Emissivity

Emissivity (Σ) is a measure of an object's ability to emit infrared energy. Different materials have different emissivity values. The thermometer's default emissivity is 0.95, suitable for most organic materials and painted/oxidized surfaces.

  1. Press and hold the EMS button for approximately 5 seconds to enter emissivity adjustment mode.
  2. The tenth decimal place digit of the emissivity value will start flashing. Use the + key to increase the value or the - key to decrease it.
  3. Press the EMS button again. The hundredth decimal place digit will start flashing. Use the + key to increase the value or the - key to decrease it.
  4. Press the EMS button to confirm and complete the adjustment.

Tip for reflective surfaces:

For accurate temperature measurements on shiny or polished metal surfaces (which have low emissivity), it is recommended to adjust the emissivity value using the provided Emissivity Reference Chart. Alternatively, place a piece of masking tape on the surface, wait about 30 minutes for the surface temperature to stabilize, and then measure the temperature of the taped area. This can improve reading accuracy.

Emissivity Reference Chart

MaterialFeatureEmissivityMaterialFeatureEmissivity
AluminiumOxidized0.20-0.40Humanskin0.98
Polished0.02-0.04GraphiteOxidized0.20-0.60
BrassOxidized0.40-0.80PlasticTransparency >0.5mm0.95
Polished0.02-0.05Rubber0.95
Gold0.01-0.10Plastic cement0.85-0.95
IronOxidized0.60-0.90Concrete0.95
SteelOxidized0.70-0.90Cement0.96
Asbestos0.95Soil0.90-0.98
Plaster0.80-0.90Mortar0.89-0.91
Asphalt0.95Brick0.90-0.96
Rock0.70Marble0.94
Wood0.90-0.95TextileAll kinds0.90
Charcoalpowdered0.96PaperWithcolor0.95
Carbon0.85Sand0.90
Lacquerworklackluster0.97Clay0.92-0.96
Carbon Cement0.90GravelTableware0.95
SoapBubble0.75-0.80Glass0.85-0.92
Water0.93Textile0.95
Snow0.83-0.90Heatedfood0.95
Ice0.96-0.98Plastic0.95
Frozen Foods0.95Oil0.94
Ceramics0.95Steelandiron0.80
Limestone0.98WoolNatural0.94
Paint0.93LeadOxidized0.50

4.5. Object Distance Ratio (D:S)

The object distance ratio (D:S) determines the accuracy of measured temperature readings. It describes the relationship between the distance to the target (D) and the diameter of the measurement spot (S).

  • The smaller the measurement spot, the closer you need to be to the surface.
  • The larger the measurement spot, the farther you can be from the surface.

For example, a D:S ratio of 12:1 means that at a distance of 600 mm, the measurement spot diameter is 12 mm. The thermometer will display the average temperature of this 12 mm diameter area.

4.6. Automatic Power Off

To conserve battery life, the infrared thermometer will automatically power off after approximately 15 seconds of inactivity.

5. Maintenance

5.1. Cleaning the Lens

  1. Use a dust blower to remove any loose particles.
  2. Gently brush away any remaining debris with a soft brush.
  3. Carefully wipe the lens with a wet cotton ball (moistened with water).

Note: Do not use solvents to clean the lens.

5.2. Cleaning the Shell

Wipe the exterior of the thermometer with a soft cloth dampened with soapy water.

Note: Do not immerse the thermometer in water.

5.3. Battery Care

If the instrument is not used for a long time, remove the batteries to prevent potential damage from battery leakage.

6. Troubleshooting

  • Continuous "BiBi" Sound: If the thermometer continuously emits a "BiBi" sound when turned on or during testing, check if the High Temperature Alert (HAL) or Low Temperature Reminder (LAL) settings are too high or too low. Adjust them as described in Section 4.3.
  • Inaccurate Readings:
    • Ensure the target is not behind glass, as the thermometer measures surface temperature only.
    • Verify that steam, dust, or smoke are not affecting the measurement area.
    • If measuring reflective surfaces, adjust the emissivity setting or use the masking tape method described in Section 4.4.
  • Device Malfunction: If the infrared thermometer malfunctions or appears damaged, do not use it. Contact customer support or send the device for repair as per the safety guidelines.
  • Low Battery Indication: If the low battery symbol appears on the display, replace the 9V (6F22) battery immediately.

7. Specifications

AttributeValue
Product NameInfrared Thermometer
Model NumberJD04
TheoryMultifunctional Thermometer
StyleHandheld
UseHousehold
Temperature Range-50°C~800°C (-58°F~1472°F) / -50°C~1500°C (-58°F~2732°F)
Max Measuring Temperature49°C & Under (Note: This likely refers to a specific setting or default, as the device supports much higher ranges)
Temperature Accuracy≥100°C, ±2% / ≤100°C, ±2°C
Response Time0.5 seconds
Adjustable Emissivity0.1-0.99
Distance to Spot Ratio (D:S)12:1/16:1 / 30:1/50:1
Resolution0.1°C (0.1°F)
Display TypeDIGITAL
Display Size2.0 - 3.9 Inches
Backlight DisplayYes
LaserTwo-point laser positioning
Operating Temperature0°C-50°C (32°F-122°F)
Operating Humidity10-95% RH (non-condensing)
Storage Temperature-20°C~50°C (-4°F-122°F)
Battery Type9V6F22 battery
Battery IncludedNo
Automatic Shutdown1 minute (after 15 seconds of inactivity)
CertificationCE, RoHS
OriginMainland China

8. User Tips

Based on user feedback, here are some helpful tips for using your NJTY JD04 Infrared Thermometer:

  • Users appreciate the fast delivery and good quality of the product, indicating reliable performance.
  • The device is generally found to work well, suggesting user-friendly operation and accurate readings for common tasks.
  • Many users find it a great item for their needs.

9. Warranty and Support

For any malfunctions or concerns, please refer to the safety information section (Section 1) regarding sending the infrared thermometer for repair. For detailed warranty information, please consult the official product documentation or contact the seller directly.

A comprehensive user manual in PDF format is available for download: Download User Manual (PDF)

© 2024 NJTY. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.